Product

1 Channel, MIL-STD-1553, Dual Redundant, Transformer Coupled, Assisted Mode Capable (AMC)

FTA

-

North Atlantic Industries

FTA - North Atlantic Industries

MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).

Product

High Voltage Switching Systems

HXV Series

-

Cytec Corp.

HXV Series - Cytec Corp.

HXV products are high voltage systems intened for Hi-pot / IR or High voltage switching. They can be configured to drive from 32 to 128 switch points per chassis and can be configured as multiplexer (1xN) or Matrix (NxM) configurations. Stand HXV chassis are used for signals up to 5000 VAC rms ( 7400 V peak ) and can carry up to 5 amps of current. Custom systems can be built up to 25KV. Most of the modules used in these systems are 1xN multiplexers or 2x4 matrix modules that can be combined to form larger multiplexers or matrices. Connector options for standard HXV include 5 way banaba jacks / binding posts, Shrouded Banana Jacks or SHV ( High voltage BNC) if you need to use a high voltage cable with a grounded shield for safety applications. Control options include 10/100BaseT Ethernet LAN, RS232, GPIB or optional manual control. Standard HXV systems use high voltage reed relays. Custom HXV systems up to 25KV use application specific relays and connectors from a variety of vendors based on required specifications.

Product

RF Filters

-

Smiths Interconnect

Smiths Interconnect

Smiths Interconnect is committed to providing technically advanced, high quality “state-of-the-art” RF Filters, Multiplexers, Switched Filter Banks, and Integrated assemblies, from 100 KHz to 65 GHz. All products are subject to the same rigorous design, manufacturing, and inspection criteria. Regardless of the application, our internal process and procedures help ensure that all products are fully compliant to all specifications. Our R & D activities are constantly evaluating new materials, plating techniques, and manufacturing processes to offer the highest performing components available today.

Product

With SAT-IF input EDFA

HA4600/IF

-

Hangzhou Huatai Optic Tech. Co., Ltd.

HA4600/IF - Hangzhou Huatai Optic Tech. Co., Ltd.

Huatai HA4600/IF series, is narrow-band multiplexing EDFA suitable for L-Band fiber link application. With build-in 1550nm Internal Modulation SAT-IF optical transmitter, used for inter-cutting DBS. The WDM inside will multiply the signal from TX and main line signal that is inputted from outside, then the combined signal will enter EDFA to be amplified to serve the local subscribers. To avoid the interferes caused by mismatching of the optical output power between TX and main line signal from outside, output power of the TX can go through a VOA, thus, it can be adjusted or set from the front panel. This unit is simple and clear, easy to be installed and tested. It offers a high quality and cost-effective solution for inter-cutting DBS into full optic relay 1550nm fiber CATV system and second-stage service area.

Product

Reverse Transcription and Polymerase

ThermaStop-RT

-

ThermaGenix Inc.

ThermaStop-RT - ThermaGenix Inc.

RNA oligonucleotides from cells and viruses can be amplified for detection using the methods of Reverse Transcription and Polymerase Chain Reaction (RT-PCR).  In a first step, a complementary strand of DNA (cDNA) is synthesized using a primer and reverse transcriptase.  The cDNA is then amplified using standard PCR techniques.  This can be accomplished by taking an aliquot from the reverse transcription reaction and adding a DNA-dependent DNA polymerase (e.g. Taq) and other reagents and then doing PCR.  That method is commonly called "Two-step RT-PCR", or "Two-tube RT-PCR".  Alternatively, all reagents, including both enzymes and gene-specific primers can be included in a single tube in order to do both reverse trancription and PCR without the need to open the tube between those reactions.  That method is commonly called "One-Step RT-PCR" or "One-Tube RT-PCR".  Both methods can include primers for a single target or for multiple targets (i.e. multiplex RT-PCR).

Product

Video Multiplexer

RVG-VM1

-

Curtiss-Wright Defense Solutions

RVG-VM1 - Curtiss-Wright Defense Solutions

The proliferating number of sensors on-board todays ISR platforms increases video management system complexity. As mission complexity increases so does the number of sensors on-board todays platforms. Because each sensor provides different critical information, its imperative that operators have the ability to view multiple sensor outputs on a single display.

Product

Relay Card

MRM16 / MRM04

-

Digitaltest GmbH

MRM16 / MRM04 - Digitaltest GmbH

Our MRM is a relay card for universal connection of many kinds of signals. It serves as a basic module and is available as a variant with 16 NO relays or as a variant with 4 x (7:1) multiplex structure.

Product

Multiplexer

LI-8250

-

Li-Cor Environmental, Inc.

LI-8250 - Li-Cor Environmental, Inc.

Central to a LI-COR long-term system is the LI-8250 Multiplexer. The LI-8250 acts as a single point of access to interact with and control a LI-COR gas analyzer and up to 36 chambers or flasks.