Thermocouples
Thermocouples are junctions of two dissimilar metals that produce a very small voltage proportional to the temperature of the junction.
-
Product
PXI Millivolt Thermocouple Simulators
Series 41-760
-
This series of PXI Thermocouple Simulator Modules is available in a choice of 32, 24, 16 or 8 channelseach channel providing a low-voltage output across two connector pins capable of providing 20mV with 0.7V resolution, 50mV with 1.7V resolution and 100mV with 3.3V resolution, covering most thermocouple types. These thermocouple simulators use two wire outputs with a remote output reference sense to ensure the modules deliver accurate low-level voltages, even if the system has common mode voltages present. In addition, each simulation channel is also able to provide an open circuit setting to simulate faulty wiring connections to a sensor.
-
Product
Precision RTD Simulator
RTD Series
-
The RTD Series Precision RTD (Resistance Temperature Detector) Simulator provides a very broad-range of absolute resistance values that replace RTD's and thermocouples. Thermocouples present a resistance that depends on the temperature. The RTD simulator effectively replaces an RTD to test, analyze, and calibrate RTD measuring systems. The RTD Series simulator is a precision resistance source with excellent characteristics of accuracy, stability, temperature coefcient, and power coefcient. All these features serve to make it a laboratory resistance standard, exceeded in performance only by stand-alone standard resistors. The special design of the RTD Series provides absolute accuracy, and requires no zero resistance subtraction from any setting Special design of the RTD virtually eliminate zero resistance and switch contact variations, providing the specified absolute accuracy over the entire range.
-
Product
Dataloggers
-
Data loggers with one or more signal channels for DC and AC voltages and currents, thermocouples, Pt thermometers, process signals and serial data interfaces RS232 / RS485 are designed for industrial use. They can also be used as monitors or process controllers with additional data and signal outputs for control purposes. The devices are designed for panel construction and have communication software for Windows applications.
-
Product
MAX31855 T-Type Thermocouple Arduino Shield
SEN-30004-T03
-
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino.Each order comes with one board and a set of four female, long extension, headers that can be soldered to the board. If stacking two of these modules on top of each other, please order both a Ch 0-3 and a Ch 4-7 board, as well as an additional set of headers for stacking. We're working on sourcing even longer headers, but the ones currently available are not long enough to stack as-is (they need to be double-stacked).The MAX31855T supports a measured temperature range of -270C-400C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or MegaNote: we also offer a universal version of this board in a smaller for factor, the SEN-30003-T.FeaturesType-specific, miniature-sized vertical thermocouple connectors (vertical flat blades, see pics)Measures four (4) thermocouple channels, full extended range.Boards are stackable. Up to 8 thermocouple channels may be connected to an Arduino.14-bit SPI interfacePlugs directly into an Arduino Uno or Mega form factor with built-in voltage level translation on-board.Standard Arduino female headers required for easy configuration, one set included with order (1-6x1, 2-8x1, 1-10x1 0.1" female stackable headers), not soldered on.Detects shorts to GND or VccDetects open thermocoupleOther versions available (K, J, and T stocked). Contact Customer Service to place a custom order.Mounting holes for 4-40 sized screwsConnections are spaced for 0.1" pin headerDesigned, manufactured, tested and shipped from the USA The MAX31855T supports a measured temperature range of -270C-400C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
-
Product
MAX31856 Thermocouple Sensor Arduino Shield
SEN-30007-T
-
Quad channel thermocouple Arduino shield based on the MAX31856 universal digital thermocouple interface IC. This is an exciting update of the MAX31855, with improvements in resolution (19 vs 14 bits), on-board temperature reference (6 vs 4 bits), and compensation (fully compensated vs nonlinear correction required). The MAX31856 is interfaced via 4-wire SPI with options for interrupt triggering. An LDO and a high-speed level shifter are included on ALL device pins to allow interfacing with to any Arduino - both 3.3V and 5.0V variants - without sacrificing device performance in any operating condition.
-
Product
REM-11120, 4-Channel Thermocouple, 1-Channel Voltage, Temperature Input Module for Remote I/O
784750-01
-
4-Channel Thermocouple, 1-Channel Voltage, Temperature Input Module for Remote I/O - The REM‑11120 is a temperature input module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the REM‑11120 from a real-time controller such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. The REM‑11120 also has an adjustable filter time for improved measurement quality and optional external cold junction compensation (CJC) or PT100 resistance temperature detector (RTD) measurements.
-
Product
LED Driver Aging Rack
LEDRACK-100W192P
-
• Application range: LED driver and multi channel driver power aging. It has equipped with computer operation and monitor system. The working condition can be set by the computer, and the computer will record real time data to do statistical analysis. • The parameters of load can be set freely on the software, to monitor the real time voltage, current, and power etc • Load mode: CC, CV, CR, CP, and LED • Aging Control System includes: ON/OFF control signal output; Signal of relay switch control; K type thermocouple temperature acquisition • The channels are parallel connected under arbitrary load mode, which can allow product power expansion • The LED Driver Aging rack will design according to customer’s LED driver power and aging quantity per time • Automatic current switching function (optional) • AC power meter to measure modules, and test power input characteristics (optional) • Temperature monitoring function at product zone (optional) • PWM dimming and two sets of logic control signal function (optional)
-
Product
Cable Assembly, Receiver, Thermocouple, 36", TB-4353
540291010262
-
Cable Assembly, Receiver, Thermocouple, 36", TB-4353
-
Product
Cooking Alarms
-
High quality, accurate cooking alarm thermometers (sometimes called leave-in probe oven alarms) are critical to the success of any process that requires maintaining a target temperature over time, including grilling, smoking, and roasting meats, baking breads and pastries, candy making, home brewing and much more. Choose from two-button simplicity, high and low alarms, continuous min/max display, single or dual channel, trim cal features, and thermocouple or Pro Series® probes.
-
Product
Gauge Type T Thermocouple Wire
W-TW-20
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Wideband True RMS AC Voltmeter
323
-
The Ballantine 323 True RMS analog ac voltmeter uses advanced true rms circuitry to achieve square law response from rugged, fast responding silicon diode detectors with no thermal lag and overload vulnerability inherent in thermocouple devices.
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J0
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Temperature Module
U1586B
-
The U1586B temperature adapter expands the capabilites of your handheld oscilloscope or handheld digital multimeter to measure temperature, either in °C of °F. To be used with a K-type bead thermocouple, and with approximately 1600 hours battery life with an alkaline battery, this adapter ensures you get the most out of your handheld scope or DMM purchase.
-
Product
Scienlab Measurement & Control Module
SL1062A
-
The Measurement & Control Module SL1062A is portable temperature measuring module for record thermocouple - temperature sensors of type K for a temperature range of -100 to +1300 °C and with 16 channels. The module can be used either as a stand-alone device or as extension for a Scienlab Battery Test System.
-
Product
Condition Monitoring
-
m+p Coda is a versatile monitoring system that captures and records signals coming from sensors such as accelerometers, thermocouples, strain gauges, and pressure transducers. Limit checking and alarm monitoring is provided for every active channel. The active channels are clearly displayed in a separate window, out-of-limit data can be seen at a glance. Alarm events are entered into a log file and can be reviewed at any time. You have the option to change the alarm limits online at any time without stopping the data acquisition.
-
Product
Thermal Profiler
MEGAM.O.L.E.® 20
-
Do you demand the highest density of thermocouples placement possible on your Hi-Reliability, High-Value PCB? ECD's got your Spec! Do you expect a software package that flexes with your workflow, providing customizable data extractions, Imports of your .MDM M.O.L.E. libraries and compatibility with your intranet, Excel, and all ECD M.O.L.E. profilers?
-
Product
Thermocouple Vacuum Gauge Tubes for Medium Vacuum
DV-6 Series
-
Teledyne Hastings, manufacturer of the original DV-4, DV-5, and DV-6 thermocouple vacuum gauge tubes, produces vacuum measurement equipment with exceptional stability, accuracy, and reliability under the most demanding conditions.The Teledyne Hastings’ DV-6 series thermocouple vacuum gauge tube acts as a localized sensor which is then paired with a selection of meters or controllers to provide reliable, cost-effective measurements in diverse applications. The robust sensor gauge tube is easily installed into vacuum systems and when properly excited, generates a thermoelectric voltage to provide a vacuum pressure measurement based on gas density. The DV-6 thermocouple vacuum gauge tube fully compensates for temperature and rate of temperature change.Thermocouple gauge tubes are calibrated on vacuum systems that contain N2 or Air, but can be used with other gases. Additionally, thermocouple gauges and their controllers can be recalibrated when a replacement thermocouple gauge tube is installed, following instructions in the manual. However, our DB-20 reference tube is available to confirm meter/controller performance. A complete line of installation accessories are also available to simplify the integration of our thermocouple gauge tubes into a variety of vacuum systems. Our goal is to provide “one less thing to worry about”, when performance matters! With a wide range of meter, fitting, relay and output options, the DV-6 series provides a reliable pressure measurement in numerous industries and applications.
-
Product
ATEX, IECEx Dual Channel Universal Temperature Transmitter With HART Protocol
SEM310X MKII
-
The SEM310X is an ATEX, IECEx approved universal programmable HART temperature transmitter which accepts most commonly used Pt100, thermocouple, mV and slide-wire sensors and generates an industry standard (4 to 20) mA transmission signal
-
Product
Handheld Economic Process Calibrator
VA702
-
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
This Multifunction calibrator combined voltage. current .resistance .thermocouple temperature .RTD in one device.
-
Product
Thermometers
-
The palm-sized Sauermann Si-TT3 dual input thermometer easily measures K thermocouple temperature.
-
Product
Compact USB Data Logger with Display
DW-USB-LCD
-
The Portable Series DW-USB-LCD USB Data Loggers displays and records temperature, humidity and dew point. The easy-to-read LCD display shows the current temperature or humidity along with the minimum and maximum reading since last reset. For applications that require more accuracy, a high accuracy temperature and humidity model is available. Thermocouple models can accept any J, K, or T type thermocouple with a mini-plug connector.
-
Product
8 Channels Thermocouple, LV A/D
TC1
-
A thermocouple is a temperature-measuring device typically consisting of two dissimilar conductors that contact each other at one or more spots. It produces a voltage when the temperature of one of the spots differs from the reference temperature on other parts of the circuit. Thermocouple temperature sensors are widely used for measurement and control, and can also convert a temperature gradient into electricity.
-
Product
Thermocouple Contact, ITA, Constantan, Type T(°C)
610113149
-
Primary mating contact 610113148.
-
Product
Vacuum Sensor, Thermocouple Vacuum Gauge for High Vacuum
DV-5 Series
-
Teledyne Hastings, manufacturer of the original DV-4, DV-5, and DV-6 thermocouple vacuum gauge tubes, produces vacuum measurement equipment with exceptional stability, accuracy, and reliability under the most demanding conditions.
-
Product
Signal/Thermocouple, Module, Receiver, TriPaddle/ Thermocouple, 84/12 Position
510104261
-
Signal/Thermocouple, Module, Receiver, TriPaddle/ Thermocouple, 84/12 Position
-
Product
Thermocouple Extension Lead
EXT-6
-
The EXT-6 - 6 foot, Type T Thermocouple Extension Lead. Flexible vinyl covered.
-
Product
Data Acquisition Recorders & Loggers
DAS1800
-
The DAS1800 can be configured for a wide variety of applications with slots for 10 input modules each supporting 4 or 8 measurement channels. Acquire data from any sensor with a voltage or current output (with shunt), or directly measure voltage, resistance, or temperature using thermocouples or resistance temperature detectors (RTDs).
-
Product
Digital Telemetry Solutions
-
For measurements on rotating components and moving machinery, imc offers modern telemetry systems for a wide variety of tasks: whether single-channel torque monitoring of a rotating shaft, multi-channel strain gauge and temperature measurements on a train wheel-set or non-contact power measurement on a vehicle drivetrain in harsh environments. There are transmission electronics available for a large variety of sensors, such as strain gauge (quarter-, half- and full-bridge), thermocouples, PT100/1000, as well as IEPE sensors and voltage signals.
-
Product
Temperature Sensors
-
We offer a variety of models of type-K temperature sensors / thermocouples. There is a standard temperature sensor, such as: surface sensor, penetration sensor, immersion sensor or special sensor with an adhesive tape, a patch, a Temperature Sensor overview screw, or a flexible cable. Consider the different combinations of materials and measurement ranges of a temperature sensor. With the help of thermal elements, temperature measurement problems can be solved in industrial processes, in machines and installations, such as in the environmental sector, and reliable results obtained.
-
Product
MAX31855 J-Type Thermocouple Sensor Breakout
SEN-30001-JDP
-
Breakout board for the MAX31855J digital thermocouple interface IC. Measured temperature range is -210C-1200C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header and four mounting holes for standoffs and 4-40 screws. It does not contain a mini thermocouple connector.
