JTAG Emulators
Exercise a processor's (DUT) on-chip debug services to perform JTAG emulation and debug.
See Also: JTAG, JTAG Controllers, JTAG Debuggers, iJTAG, P1687
-
Product
Portable JTAG Boundary-Scan Controller with USB (1.1 and 2.0 High Speed), Ethernet & Firewire Interfaces
JT 37x7/TSI
Controller
High speed and performance portable JTAG Boundary-scan controller, containing three interfaces to the test system: USB (1.1 and 2.0 high speed), Ethernet and FirewireThe controllers are targeted at demanding manufacturing test applications, fast in-system flash memory programming and programmable logic configuration. The JT 37×7 is available in different operating levels (memory options) to suit your specific environment and application. Each unit is supplied with a four TAP port signal conditioning module the JT 2147 ‘QuadPOD‘The JT 37×7 DataBlasters are a family of high speed and performance, up to 40 MHz TCK, boundary-scan controllers. Besides being available as bench-top unit with USB/E-net/FireWire interface, these controllers also come as 19″ rack-mountable instrument with the same three interafces and as plug-in cards in PXI(e)and PCI(e) formats.
-
Product
PoE LLDP Emulation (PSE) & Analysis for 802.3at & 802.3bt
-
The IEEE 802.3 specifications require that Type 2, Type 3, and Type 4 PDs implement PoE LLDP and use the Power via MDI TLV for power negotiation. This requirement therefore applies to any PD that draws more than 13 watts. The PDA-600 family includes an option to flexibly emulate any PSE while capturing and analyzing the LLDP power negotiation protocol from a PD.
-
Product
Network Delay Emulator
-
BGP Network Delay Emulator. The Border Gateway Protocol or BGP is at the core of the modern Internet. Large corporate and government enterprise networks are increasing their use of BGP to interconnect different administrative and country specific regions
-
Product
JTAG Debug Probe for Cortex-M
J-Trace PRO
-
SEGGER Microcontroller GmbH & Co. KG
J-Trace PRO for Cortex-M is setting a new standard for trace probes. It enables continuous streaming trace via its Gigabit Ethernet interface, lifting the limitations by internal buffers and slow data transmission.J-Trace PRO can capture omplete traces over long periods - thereby enabling the recording of infrequent, hard-to-reproduce bugs. This is particularly helpful when the program flow 'runs off the rails' and stops in a fault state. It also supports extended trace features, such as code coverage (so engineers have visibility of which parts of the application code have been executed) and execution profiling (providing visibility as to which instructions have been executed and how often - so hotspots can be addressed and optimization opportunities identified).
-
Product
Network Emulator
Calnex SNE-X
-
A multi-port, high-performance network emulator to drive product/application quality and reduce the cost of test with rigorous, scalable test capability.
-
Product
EPC Emulators
-
The EPC Emulators consist of the MME Emulator, HSS Emulator, SGW Emulator, PDN-GW Emulator, and the PCRF Emulator, which can be used together to simulate the complete LTE Packet Core or individually to create a combination of real and simulated Core Network elements. These Emulators includes all the network interfaces and implements all the communication protocols required for core network equipment to operate in an LTE/SAE network.
-
Product
IMS-SIP Network Emulator Software
E6966B
-
Wireless telephony networks are increasing capacity for high throughput Internet Protocol (IP) packed-data by utilizing radio access technologies such as LTE and HSPA. Session Initiation Protocol (SIP) and IP Multimedia Subsystem (IMS) are progressively being adopted as part of the network infrastructure to carry traditional wireless telephony services over an all-IP network. SIP provides control of communication sessions whilst IMS is the framework that allows delivery of multimedia services over IP. With this new capability comes the need for developers and operators to move their focus to testing user equipment (UE) in this new network environment.
-
Product
eNodeB Emulator
-
The eNodeB Emulator includes UE simulation, and can be used to test the complete LTE Packet Core or individual Core Network elements, MME, SGW, PGW. It implements all the required protocols - S1AP/SCTP to communicate with MMEs over S1-MME interface and GTP-u to communicate with S-GW over S1-U interface.
-
Product
Fading Emulator
RI 241
-
RI 241 Fading Emulator is a radio channel emulator designed to replace the obsolete Agilent 11757B Multipath Fading Simulator.
-
Product
Mixed Signal JTAG Tester
JT 5705
-
The JT 5705 series offer a unique combination of JTAG TAP controller (tester) interfaces plus digital and analog I/O in compact desktop package.Use the ‘mixed-signal’ features to measure power supplies, clock frequencies or test DACs and ADCs. Add your own capability through use of CoreCommander FPGA our generic bridge/translator system.
-
Product
High-Performance LAN & USB JTAG Controller
NetUSB II™
Controller
Boundary-scan has proven itself time and again to be a truly versatile interface for structural test, embedded functional test, built-in self-test (BIST), software debug, and in-system programming. Supporting such diverse applications requires a controller with high performance specifications and diverse features.
-
Product
Boundary Scan Test and JTAG Programming Tool Set
onTAP® Series 4000
-
onTAP is a comprehensive boundary scan testing and JTAG programming tool set that bolsters the most accurate possible fault coverage in an affordable and expedient manner, while providing support for the entire product life cycle.
-
Product
HEV / EV / Grid Emulators and Test Systems
-
With Scienlab test systems and test software, Keysight offers customized test environments for the development and testing of electronic components according to hybrid and electric vehicle testing standards. Our solutions help you to accelerate your e-mobility applications from the battery, Battery Management System (BMS), inverter, the charging interfaces of Electric Vehicle (EV), and Electric Vehicle Supply Equipment (EVSE).
-
Product
4 TAP JTAG Boundary-scan Controller for Teradyne Systems
QuadTAP/CFM
Controller
The Corelis QuadTAP/CFM high-speed multi-TAP boundary-scan system makes advanced, multi-TAP boundary-scan testing within ICT systems a reality. By combining ICT and boundary-scan, test engineers gain benefits from both technologies for the highest possible test coverage, speed, and capability.Specifically designed for integration into Teradyne TestStation and GR228x testers, the QuadTAP/CFM and QuadTAP/CFM Expander enable a clean, convenient multi-TAP boundary-scan solution.
-
Product
Surface Mount Package Emulation
SMT Adapters
-
Ironwood’s SMT package emulation adapters are often called “surface mount feet” or “emulator bases”. These adapters provide access and interconnections to surface mount lands. Typically, the adapters are soldered to the target board in place of the IC device and provide a pluggable array of pins interface for sockets, probing adapters, package converters, and even board-to-board connections. These adapters are often utilized as a base for many of our probing adapter products. We constantly innovate to provide the most reliable, cost effective interfaces available. For example, many of our PLCC, QFP and SOIC emulation bases use our proprietary shaped solder techniques, replacing expensive, and often fragile, J-lead and Gull Wing leads. Shaped solder parts are easily fluxed and reflowed onto the target system. Our emulator bases can present either a male or female interface at 1.27mm or 1mm or 0.8mm pitch gold plated array pins for pluggable connection.
-
Product
In-Circuit Emulator
DS-XA
-
* Emulates XA Derivatives * 2MByte Code and Data Memory * Memory With Mapping Capabilities * Real-Time Trace * Frequency Range up to 30MHz @ 5V * Source-Level Debugger For C And Assembler * MS-Windows Debugger Software for Windows NT and 95 or Later * 3.3V And 5V Emulation Support * Support for ROMless and ROM Microcontrollers * PLCC Emulation headers
-
Product
Emulation Adapters
-
With some of the more advanced 32-bit microcontrollers and SoCs, the full program and data trace capabilities of the device are not made available on production silicon. Instead, semiconductor vendors provide special 'emulation devices'. These typically feature more pins than the production device, thereby providing the interface to the trace interface.
-
Product
Basic Protocol Multi-Terminal Emulation
Sy629PMC-BPT
-
The Sy629PMC-BPT card provides a convenient means for transmitting and receiving data over an ARINC 629 bus in accordance with the transmit and receive programme defined by data written into the XPP and RPP memory. In particular, this product can emulate up to 120 terminals transmitting on an ARINC-629 data bus whilst correctly maintaining the Basic Protocol.
-
Product
Live PD Emulation for the PSL-3424A/L
-
Flexibly Mimic Class 0 to Class 8 Powered Device Per PSL-3424 Test Port. Configure up to 96 IEEE 802.3 PD’s on Any Combination of 2-Pair and 4-Pair PSE Ports with Loading up to 100W on Every Port. Emulated PD’s Automatically Handle PSE Power Demotions (Assigned Class). User-Defined Powered Device Load with Optional Cable Loss Modeling. Emulate 802.3at and 802.3bt PoE-LLDP* Negotiations and Power Adjustments (PSL-3424L). Monitor Multi-Port Live Emulation Status.
-
Product
JTAG Isolation Protection
-
Our line of JTAG isolators help protect your investment in computers, development boards, debug probes, and lab equipment. Each model connects easily between your target board and debug probe.
-
Product
Dual Mobile Comm DC Source w/ Battery Emulation
66319B
DC Power Supply
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections. The Keysight 66319B dual output mobile communications dc source provides two outputs for testing both the main battery power and the battery charger circuitry, allowing customers to test phones and chargers with the same equipment. This feature helps save on rack space (2 outputs in a rack box) and eliminates the need for two separate power supplies.
-
Product
high-speed JTAG debugger
Bus Blaster v4
-
Bus Blaster is an experimental, high-speed JTAG debugger for ARM processors, FPGAs, CPLDs, flash, and more. Thanks to a reprogrammable buffer, a simple USB update makes Bus Blaster v2 compatible with many different JTAG debugger types in the most popular open source software.
-
Product
10M/100M/1G Ethernet Network Emulator
VirtualNetTM GE
-
VirtualNet-1G is a high-performance Network Emulator that replicates real world Ethernet network effects such as latency and errors on user traffic in a controlled environment. The VirtualNet-1G emulator uses customized ICs to support full line rate performance at all frame sizes and impairment settings. The emulator can be transparently installed in-line as shown in the diagram below. VirtualNet-1G emulator has an intuitive and easy to use GUI interface and a very powerful TCL based CLI to aid in configuration and testing.
-
Product
HPGL Plotter Emulator software
Plottergeist
-
Plottergeist "the phantom plotter" emulates all the common HPGL plotters. It runs on a standard PC equipped with a GPIB card or using RS-232, and connects to test equipment or another computer. The software behaves like a real plotter, with the exception that the PC screen is the paper.
-
Product
Car-to-X Signal Strength Emulator
-
Qosmotec Software Solutions GmbH
QPER-C2X is a special adaptation of the signal strength emulator QPER, designed for mobile and Vehicular Ad-hoc Networks (MANet and VANet). Every radio devices in such an infrastructure-less network acts as a sender, receiver, and forwarder (router). Therefore, the ports of the QPER-C2X hardware are fully connected with each other by dynamically controllable attenuators. The system is fully designed for frequencies up to 6 GHz, since wireless communication for Intelligent Transport Systems (ITS) is based on the WLAN standard IEE 802.11p from 5.850 MHz to 5.925 MHz. The connected ITS stations can be either on-board units, as they are built into cars, or road side units that are used by road infrastructure (traffic lights, road work area delimiters, velocity signs). For tests in the lab, radio modules of such ITS stations are each kept in a shielding box that prevents any unwanted radiation over the air.
-
Product
BGAN Network Emulator
BNE
-
Square Peg Communications Inc.
The Gatehouse BGAN Network Emulator (BNE) is a test tool developed and optimized to work in concert with the Square Peg BPLT to provide end-to-end emulation of the BGAN Network. The combination of the BPLT and BNE provides an on-the-bench emulation of the I4 satellites, the BGAN Radio Access Network (RAN) and the Core Network (CN). It is a very powerful test solution that enables terminal manufacturers, system integrators and application developers to test their applications thoroughly and consistently and to verify that applications are optimized to work under any network condition thereby providing the best possible user experience.
-
Product
JTAG Test Software
-
JTAG Technologies software has been subject to a program of continuous development for over 20 years. The first products, launched in 1991 formed the start of our 'Classic' range of software and featured the first automatic boundary-scan test program generator (ATPG) for PCB interconnects plus associated test execution and diagnostics software. In 2006 JTAG Technologies launched it's new flagship tools platform JTAG ProVision.
-
-
Product
Chromatic Dispersion Emulator
CS-CDE
-
The ClearSpectrum™-CDE is a chromatic dispersion emulator suited for test and measurement. This 1U half 19-inch rack-mountable module is designed to emulate tens of thousands of picoseconds per nanometer in a compact unit while maintaining very low insertion loss. It is a passive, ready-to-use emulator which can be cascaded several times to achieve higher levels of dispersion.
-
Product
JTAG Software
-
Looking for flash programming or JTAG test utilities, we have them. Our software ranges from basic command line utilities to applications that extend the emulator's use in the field or the lab.
