Scan Converters
Transform scan rates of a signal to another format.
-
Product
Sample And Hold Converters
-
A critical part of most data acquisition systems, Renesas offers several sample and hold amplifiers for general purpose and military and defense applications that include precision data acquisition systems, synchronous sampling, wide bandwidth analog-to-digital (A/D) conversion, auto-zero circuits, digital-to-analog (D/A) converter deglitching, peak detection, and high-speed DC restore.
-
Product
Xineos Scanning
-
Teledyne DALSA's leadership in CMOS innovation lets our Xineos scanning products deliver three times more sensitivity and five times more signal-to-noise performance than other standard technologies at equal X-ray dose conditions. CMOS image detectors offer numerous advantages including the ability to record smaller image details with higher resolutions – allowing for the diagnostics of medical anomalies at earlier stages, and significantly increasing the probability of early intervention, patient recovery, and reduced treatment costs.
-
Product
Testing Hardtop Convertible
-
Magtrol designed this Custom Motor Test System for the testing of motors used in hydraulic systems in hardtop convertible roof drives.
-
-
Product
Audio A/D Converters
-
Analog Devices offers audio analog-to-digital converters (ADCs) for applications such as automotive, home theater, consumer audio, and PCs. These ADCs offer cost effective solutions and easy interfacing to ADI's SHARC® processor, Blackfin® processor, and SigmaDSP™ products.
-
Product
Time to Amplitude Converters and Calibrator
-
A Time-to-Amplitude Converter (TAC) can achieve exceptional precision by using an analog technique to convert small time intervals to pulse amplitudes. When a timing application demands picosecond precision, a time-to-amplitude converter is a prime candidate. A time-to-amplitude converter is a productive solution for measurements less than 10 μs when time resolutions from 10 ps to 50 ns are required.
-
Product
Frontends & Converter
FExx Series
-
R&S®FExx external frontends extend the frequency ranges of Rohde & Schwarz signal and spectrum analyzers and signal generators up to 170 GHz. The R&S®FExx enables the up and down-conversion of the signal directly at the DUT. In an OTA environment it lowers cable losses, increases sensitivity and delivers more power at the antenna.
-
Product
x1149 Boundary Scan Analyzer
N1125A
Analyzer
The x1149 is a tool for engineers to perform structural test such as opens and shorts tests on their PCBAs. It also performs In-System Programming for devices such as FPGAs and CPLDs.
-
Product
DC/DC Converter 2 W
REM2-153.3D
-
DC/DC converter 2 W from Recom | input ranges 13.5 - 16.5 VDC | outputs +/-3.3 V | operates in ambient temperature from -40 to +95 °C
-
-
Product
DC/DC Converter 2 W
R2SX-053.3/H
-
DC/DC converter with 2 W from Recom | input ranges 4.5 - 5.5 VDC | output 3.3 V | operates in ambient temperature from -40 to +100 °C | high isolation version
-
Product
Synchro/Resolver to Digital Converters
-
Resolvers and synchros are transducers that convert the angular position and/or velocity of a rotating shaft to an electrical signal. Both deliver signals proportional to the sine and/or cosine of the shaft angle. A resolver-to-digital or synchro-to-digital converter converts these signals to a digital output corresponding to the shaft angle and/or velocity. ADI’s family of RDCs and SDCs offer solutions for these applications.
-
Product
IRIG B to NTP/SNTP Converter
-
Signals & Systems India Private Limited
IRIG B TO NTP/SNTP CONVERTER – SPC-INS-1010 is a compact DIN rail mountable protocol converter unit which synchronizes and maintains the timing and frequency requirement of power and process industry equipment using IRIG-B signal obtained from GPS receiver. It provides nanosecond accuracy when external time references are not available. It has the storage facility to store the system log file. It delivers NTP, SNTP, PFC-Pulse, RS232 & RS485 outputs. The system enables configuration and monitoring through Web-based application. It supports a wide range of power supply input either 90V-260V AC/DC or 18-36VDC or 36V-72VDC.
-
Product
Quick Scanning Moisture Meter
L601-3
-
The rugged L601-3 is specifically designed for the demanding environment of the sawmill or wood products manufacturing plant where quick-scanning of lumber is a must. The L601-3''s "Wood-Friendly" electromagnetic waves penetrate beyond the surface into the wood to a depth of 1" and provides an instant averaged reading of the board''s moisture content in a 2.5" x 2.5" x1" scanning area.
-
Product
Interface Converter
ZET 7177
-
ZET 7177 CAN→GSM interface converter can be used under conditions when there is no access to a regular connection over Ethernet, or when you need to provide a redundant channel in case of Ethernet fouling.
-
Product
Antenna Impedance Converter
-
The low noise impedance matching equipment has a high impedance input with minimized capacity. With the 50 Ω output it can be used with common EMI receivers or spectrum analyzers to measure the emissions received by an antenna on a vehicle.
-
Product
DC/DC Converter 2 W
R2SX-2424
-
DC/DC converter with 2 W from Recom | input ranges 21.6 - 26.4 VDC | output 24 V | operates in ambient temperature from -40 to +100 °C
-
Product
IRIG-B TTL TO RS485 Converter
SPC - INS - 1010
-
Signals & Systems India Private Limited
The IRIG-B TTL signal is a time synchronization protocol that can be transmitted up to 50m maximum using coaxial cable. So the relay which is to be received the IRIG-B TTL signal may be far away from the IRIG-B source. The relay may be not able to synchronize with the GPS. To avoid such an incident in the field, some of the relays have provision to receive IRIG-B RS485 signal. The IRIG-B RS485 signal can able travel up to 1200m without any booster. All Time source equipment may not be supplied with IRIG-B RS485 signal output. The converter will act as a bridge between GPS Time source and Relays for time synchronization.
-
Product
Channelized Up/Down Converters
-
Teledyne Defence & Space (TDS) Flexible Channeliser has flexible channel frequenct allocation and integrated channel filtering. The Flexible Channeliser has been selected for supply to OneWeb for its satellite payload system designed to provide low earth orbit broadband internet access worldwide.TDS has uniquely proven experience in building solutions for RF & Microwave components, Sub-Systems & Payload integration working transparently to provide a complete payload for both high volume and bespoke mission designed products.
-
Product
Line Scan Camera
Linea SWIR
-
Teledyne DALSA’s short-wave infrared (SWIR) GigE line scan camera features a cutting-edge InGaAs sensor in a compact package for a wide variety of machine vision applications.This high speed, high resolution camera is the first product in DALSA’s SWIR family. Linea SWIR features a cutting-edge InGaAs sensor in a compact package that is suitable for a wide variety of applications. With exceptional responsivity and low noise, this camera allows customers to see their products like never before. Linea SWIR is available as a 1k resolution camera with highly responsive 12.5 µm pixels, or a 512 resolution camera with larger 25 µm pixels
-
-
Product
Charge Converter
CH-6130/6140
-
The CH-6130/6140 charge converter is a simplified type of charge amplifier converting charge signal to voltage.It can be connected directly to an input BNC connector of a CCLD applicable equipment such as FFT analyzer or vibration comparator, enabling direct connection of a charge output pickup without suing a box type amplifier.
-
Product
Synchro to Digital-Resolver to Digital Converters
MRDC
Digital / Synchro Converter
Computer Conversions Corporation
Computer Conversions’ MRDC64-3 is a miniature single chip solution for providing a complete 1 x 64 speed resolver interface into any demanding industrial or military application.
-
Product
Frequency Converters
-
CAES offers a full range of custom frequency converter solutions including narrowband, wideband and block upconverters and downconverters.
-
-
Product
Sensor-Over-Ethernet Converter
MIC-FG-HSB
-
The Sensor-over-Ethernet converter board powered by FPGA. Support MIPI camera converter board /8P GMSL board. Supports up to 4K, 30FPS camera. Ultra-Low Latency Real-Time Data Processing.
-
Product
Universal Converter
C8000
-
Multi channel converter for all optek photometric and conductivity sensors and electrochemical pH electrodes. Flexible configuration of sensors, measuring ranges, units and product specific setups make the C8000 converter series a powerful device in process monitoring in both conventional and single-use systems.
-
-
Product
Scanning Slit Beam Profiling
NanoScan
-
Measure your beam as never before with the NanoScan™ beam profiler. The advantage of scanning slit beam profiling is sub-micron precision for measuring beam position and size. Scan head configurations include Silicon, Germanium, and Pyroelectric versions for a wide range of wavelengths and laser power levels. The NanoScan software is available in two versions: Standard and Professional, and includes an extensive set of ISO quantitative measurements, an M2 Wizard, and the ability to measure laser power.
-
Product
Scanning X-Ray Detectors
Shad-o-Scan
-
Shad-o-Scan is a family of scanning X-ray detectors specifically designed for the challenging requirements of high-performance industrial and scientific X-ray applications. Industry-leading TDI CCD performance enables the ultimate sensitivity and highest resolution in the industry, and ensures long detector lifetime in even the harshest radiation environments.
