-
Product
NITlab Chassis Manager Card
-
NITLAB designed and implemented a Chassis Manager(CM) card to control and monitor NITOS nodes. CM card is comprised of a general-purpose microcontroller, an ethernet microcontroller and a relays circuit. General-purpose microcontroller supports a tiny web server and can serve http requests such as power on/off and reset. Furthermore, it returns the operation status of the node and can support a temperature & humidity sensor and a light sensor as well.
-
Product
Semiconductor Testing
-
Teradyne’s semiconductor test portfolio is transforming the way you test chipsets for automotive, industrial, communications, consumer, smartphones, and computer and electronic game applications. Semiconductor devices span a broad range of functionality, from very simple low-cost devices such as appliance microcontrollers, operational amplifiers or voltage regulators to complex digital signal processors and microprocessors as well as memory devices.
-
Product
Microcontrollers (MCUs)
8-bit
-
An innovative 8-bit chip design provides a fully-integrated experience. Silicon Labs' 8-bit MCUs are ideal for IoT applications and beyond, delivering the industry's fastest speeds and lowest power.
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Renesas Synergy™ Microcontrollers
S3 Series - High Efficiency
-
Stretch application efficiency with optimized power for performance in the S3 Series. Handle data-intensive operations with minimal CPU clock cycles and a built-in Floating -Point Unit for data security with features such as Advanced Encryption Standard (AES), True Random Number Generator (TRNG), and Memory Protection Unit (MPU).
-
Product
Unclamped Inductive Load Tester
ITC55100C
-
The system has been designed around a very powerful micro-controller that gives it a timing resolution of 40ns, twenty times faster than the previous model. Its response time to the peak and zero current is improved ten times. Combined this gives greater accuracy for the charging and avalanche times and for the reported peak drain current.
-
Product
Development System
FE-51MX
-
* Emulates Philips P8xC51MA/B/C , P89C669 Microcontrollers * 1MByte Code Memory * Based on bond-out Technology * Frequency up to 24MHz 3V / 5V Operation * Huge Real Time Trace Memory * Windows Debugger for C/C++ and Assembler * Target Board Included * RS-232 or USB Interface * 64K C/ASM and 8K C++ Included
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
RL78 Family Of 8/16-bit Ultra-Low Energy MCUs
RL78/H1x
-
The RL78/H1x microcontroller family is a peripheral rich family of true low power microcontrollers integrating analoig functions, suitable for healthcare applications.
-
Product
Development System
FE-SND2
-
* Emulates Atmel AT89C51SND2 Microcontrollers * 62K Code Memory * Real-Time Emulation * Frequency up to fmax * ISP and X2 Mode Support * Windows Debugger For C, C++ and Assembler * USB or RS-232 Linked to PC * C Compiler and Assembler
-
Product
32-bit Microcontrollers (MCUs)
EFM32™
-
The energy-friendly EFM32 MCUs are ideal for ultra-low power applications. Based on ARM Cortex-M0+, Cortex-M3 and Cortex-M4 cores, EFM32 MCUs also include the most energy-friendly peripherals and energy modes to enable design of highly functional low power systems.
-
Product
MAX31855 J-Type Thermocouple Sensor Breakout
SEN-30003-J
-
Breakout board for the MAX31855J digital thermocouple interface ICs by Maxim. Measured temperature range is -210C-1200C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 2x5 pin header (8-pins used), has four vertical mini thermocouple connectors and four mounting holes for standoffs and 4-40 screws. The SEN-30003 is interfaced via 3 or 4-wire SPI with a data-ready output for specific operating modes. An LDO and a high-speed level shifter are included to allow interfacing with microcontroller devices between 3.0V and 5V (all Arduinos, Raspberry PI, etc) without sacrificing device performance (many other level shifters reduce data rates to below 500 kHz).
-
Product
Universal, Production In-System Programmer
FlashRunner Series
-
FlashRunner is a universal, production In-System Programmer.It is the result of many years of experience in developing programmingand debugging solutions for microcontrollers.
-
Product
Electricity Metering Device- Residential
ES-12B
-
Designed for the residential smart meter rollout in Great Britain, this 5 terminal single phase electricity meter is an addition to our range of SMETS2 compliant solutions.With two 100A main disconnect relays, dedicated secure microcontroller and multiple communications interfaces including Zigbee and DLMS, the ES-12B is accurate and can operate in prepayment mode.
-
Product
ST VL53L0X Time-of-Flight Range/Distance Sensor
SEN-36003
-
Highly integrated breakout board for the ST Micro VL53L0X Time of Flight (ToF) range finder sensor, which builds on the absolute ranging technology introduced with the VL6180X. The VL53L0X drops the ambient light sensing capability of it's predecessor for a 10X improvement in absolute ranging capability, bringing the maximum possible range to 2 meters! As a result, this sensor has even more uses in the robotics, cell phone and gesture recognition space. The SEN-36003 includes the VL53L0X IC mounted between two 4-40 sized mounting holes with on board 2.8V LDO and high-speed signal translation to handle interface voltages from 3V to 5V. The board is interfaced via an I2C interface and function pins have been broken out to a 0.1" pin header. All pins are translated to allow interfacing with any microcontroller in the 3V to 5V operating range.
-
Product
Multi-Axis Stage Controller
MS-2000-WK
-
Applied Scientific Instrumentation
*100 MHz Microcontroller for faster command processing and servo control.*Closed-loop DC servo control of up to four motorized axes.*Firmware upgradeable via serial connection.*0-10V DAC for single piezo axis control.*Remembers last position on power down/up.*LCD display shows axes coordinates and status.*"Zero" and "Home" buttons for simple stand-alone operations.*USB or RS232 serial control with baud rates to 115200 Baud.*Compact ergonomic tabletop control unit 6"D x 9"W x 3"H (16 x 23 x 9 cm).
-
Product
Microcontrollers
-
Frontgrade offers highly integrated, full-featured SPARC and Arm®-based Rad Hard microcontrollers ideal for system-on-chip (SoC) applications. These small footprint, low power devices are augmented with integrated analog front-end components making them ideal for mixed signal processing.
-
Product
NITOS Wireless Sensor Platform
-
The NITOS prototype wireless sensor mote, is comprised of open-source and configurable modules. NITOS mote features the ATmega32u4 microcontroller running at 8MHz and operating at 3.3V. The aforementioned microcontroller is fully compatible with the Arduino platform that enables ease of software development and provides compatibility with several commercial sensing modules. Moreover, the platform is equipped with an Xbee radio interface that enables communication with the respective gateway. The Xbee module is a tiny device ideal for setting up mesh networks and has a defined rate of 250 kbps. This module uses the IEEE 802.15.4 stack which is the basis for theZigbee protocol. Apart from the Xbee module, NITOS mote can also feature a WiFi wireless interface in order to communicate with WiFi gateways. The developed mote currently features specific sensing modules, an air temperature and humidity sensor, a light intensity sensor and a human presencesensor. Various types of sensing modules and actuators can be further integrated exploiting existing Arduino software that implements several existing communications protocols. The firmware can be easily uploaded through the on-board USB connection. Figure 1 illustrates the developed NITOS mote and the respective gateway node.
-
Product
Evaluation Kits:
Grid-EYE® AMG8834EVAL Evaluation Kit
-
Panasonic Industrial Devices Sales Company of America
Panasonic is pleased to announce the availability of the Grid-EYE AMG8834EVAL Evaluation Kit featuring TrackMe Software for its' Grid-EYE Infrared Array Sensor, which integrates a ”nanopower” Bluetooth® Smart Module and a microcontroller. The AMG8834EVAL Kit is intended for prototyping the Grid-EYE Sensor which is a 64 pixel IR camera in a surface mount package measuring 11.6mm x 8mm x 4.3mm, which integrates the MEMS Sensor, lens and I2C interface.
-
Product
Low Cost Emulator
EB-51
-
# Emulates 80C51 Microcontrollers and Derivatives# Real-Time Operation up to 40 MHz# 3.3V or 5V Voltage Operation# Source-Level Debugger for C, PLM and Assembler# DOS and MS-Windows Software# Support for ROMless and ROMed Microcontrollers# 64K of Code and 64K of Data Memory# Data Memory with Mapping Capabilities# Performance Analyzer# Real-Time and Conditional Breakpoints
-
Product
Electricity Metering Device- Residential
ES-10B
-
Designed for the residential smart meter rollout in Great Britain, this 4 terminal single phase electricity meter is the second generation version within our SMETS2 compliant solution.Taking learnings from the first generation meter, the ES-10B is a more refined SMETS2 compliant electricity meter with 100A main disconnect relay, dedicated secure microcontroller and with multiple interfaces including Zigbee and DLMS.
-
Product
SparkFun Mini Breakout
SAMD21
-
If you’re ready to step your Arduino game up from older 8-bit/16MHz microcontrollers, the SparkFun SAMD21 Mini Breakout is a great landing spot. The SAMD21 Mini Breakout is a Pro Mini-sized breakout for the Atmel ATSAMD21G18, a 32-bit ARM Cortex-M0+ processor with 256KB flash, 32KB SRAM, and an operating speed of up to 48MHz. This mini breakout provides you with an Arduino hardware option that solves the problems of low storage limits and dynamic memory stack overflows that have plagued the previous iterations of the Arduino family. Yes, the SparkFun SAMD21 Mini Breakout is even fully supported in the Arduino IDE and libraries for the Arduino Zero!
-
Product
Combination Board Tester
ATE QT2256-640 PXI
-
Qmax Test Technologies Pvt. Ltd.
Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or micro controller based boards. ATE QT2256-640 PXI system is designed as a combination board tester capable of testing highly complex and PCBs employing various techniques on a single platform. It can be easily upgraded to 640 digital channels and with programmable UUT power supplies, IEEE or PXI external instrumentation, Bus cycle signature system, ICE and integrated Boundary scan Test AC/DC parametric testing. The ATE is interfaced to an external host PC using a PCI express interface card allowing a maximum data transfer rate. Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or microcontroller based boards.
-
Product
Dual MAX31865 PT-100 RTD to Digital Breakout
SEN-30202-PT100
-
Dual channel breakout board for the MAX31865 RTD-to-Digital converter from Maxim. Two breakout hardware configurations are available standard, designed to interface with either the PT100 or PT1000 platinum RTDs. For non-standard applications, including thermistors, custom hardware configurations can be accommodated. Contact Technical Support for more information. RTD devices may be wired in 2, 3 or 4-wire configurations using the 4-pin screw terminal input. The MAX31865 breakout is interfaced via 3 or 4-wire SPI with a data-ready output for specific operating modes. An LDO and a high-speed level shifter are included to allow interfacing with microcontroller devices between 3.0V and 5V (all Arduinos, Raspberry PI, etc) without sacrificing device performance.
-
Product
Software Test Tool
testIDEA
-
The basic premise behind the development of testIDEA was simple: if our development tools have access to the source code and binary code of an embedded application, and our debug hardware can access all of the internal workings of the microcontroller, surely we can simply test embedded software on the target microcontroller.
-
Product
SparkFun LiPo Fuel Gauge
-
LiPo batteries are a great way to power your projects. They're small, lightweight, and pack a pretty good punch for their size. Unfortunately, even the best batteries eventually run low on power and when they do it's often unexpected (and at the worst time). Don't be caught by surprise next time your board suddenly powers-down! The SparkFun LiPo Fuel Gauge connects your battery to your project and uses a sophisticated algorithm to detect relative state of charge and direct A/D measurement of battery voltage. In other words, it tells your microcontroller how much 'fuel' is left in the tank. The LiPo Fuel Gauge communicates with your project over I2C and an alert pin also tells you when the charge has dropped below a certain percentage.
-
Product
BeeProg2C Programmer
-
Universal Programmer memory, microcontrollers and PLDs. This supports systems 78324 Beeprog2c programmer Elnec company is an excellent choice for factories and businesses servicing the electronic devices
-
Product
Microprocessor & Microcontroller Trainer
-
8085/8086 Microprocessor based product designed to teach students about 8085/8086 architecture and its programming techniques & provides a very simple and user friendly platform for students so they can learn about 8085/8086 Microprocessor architecture and implement their own ideas with different peripherals provided on board. Practical experience on this board carries great educational value for science and engineering students.
-
Product
Single Board Computers
ITX-P-C444
-
The ITX-P-C444 is an industrial Pico-ITX single board computer (SBC) with NXP’s i.MX8M application processor and packed with dual Ethernet, industrial I/O, and expansion options. The processor supports industry-leading video processing along with an M4 microcontroller for real-time subsystems making it an ideal fit for industrial IoT applications requiring performance in harsh conditions such as digital signage, industrial automation, energy management, building automation, among others.
-
Product
Accelerometers
-
The unit is based on micro machined MEMS technology. The unit contains a 35g sensing element. The element is scaled to optimise the resolution to suit the g range of interest. An internal amplifier provides an output between 0 and 5 volts. The on board microcontroller and temperature sensor are used for offset drift compensation. This unit can be re-calibrated at the factory.
