PXI Carriers
-
product
PXI 4x3 10GHz Matrix with Termination
40-787-518-4X3-T
The 40-787 Microwave BRIC platform is designed to provide a solution for complex RF matrix applications. Using a common mechanical platform the module can be constructed to provide scaleable non-blocking or blocking microwave matrix for frequencies to at least 20GHz.
-
product
PXI High Density MUX BRIC, 16-Chan, 40-Pole
40-570-214
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
product
Slave Dual Industry Pack Carrier
CPCI-SIP-3
The new CPCI-SIP-3Module provides a 3U high performance flexible I/Oscheme, that supports industry standard IndustryPacks. Choose from over a 100 different IndustryPacks from Alphi Tech and others. For applicationrequiring low cost, high density I/O or unique combinations, the CPCISIP-3 is the perfectsolution.
-
product
PXI 64 Channel Relay Driver Module
40-411-001
The 40-411 is the perfect solution for driving external relays from a PXI system or from Pickering Interfaces LXI modular chassis. Each module provides 64 channels of low side switching for external relays. Users need to simply connect a positive voltage source to one side of the relay coil and the other side to the 40-411 output. Each output is capable of sinking up to 1 Amp of continuous current.
-
product
3U CPCI Dual IP Carrier
CPCI-SIP
The CPCI-SIP module provides a 3U high performance flexible I/O scheme that supports industry standard Industry. PacksÔ. For application requiring low cost, high density I/O or unique combinations, the CPCI-SIP is the perfect solution. The CPCI-SIP is also available with the Industry Pack lines routed to the CompactPCI P2 connector for application that require rear panel I/O.
-
product
PXIe-8861, 2.8 GHz Quad-Core PXI Controller
787567-01
PXIe, 2.8 GHz Quad-Core PXI Controller - The PXIe‑8861 is an Intel Xeon 4‑Core embedded controller for PXI Express systems. You use it for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe‑8861 includes two 10/100/1000BASE‑TX (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, two Thunderbolt™ 3 ports, and other peripheral I/O. Thunderbolt and the Thunderbolt logo are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries.
-
product
Single-Channel USB Carrier Demodulator
CD17
The Validyne model CD17 is a USB-powered carrier demodulator for Validyne variable reluctance pressure sensors such as the DP15, DP45 and DP103. The CD17 allows any Validyne variable reluctance sensor to be used directly with a PC via the USB port. Communication and power via USB interface provides remote zero and span adjustment as well as digital pressure readings in mV/V. Drivers and software for the USB interface are included.
-
product
Time Interval Counter PXI Card
GTX2200 Series
The GTX22x0 family of PXI universal time interval counters offer many of the measurement and timing functions of high-end stand-alone frequency counters, including accumulate, auto ratio, frequency, fast frequency (GTX2220 and GTX2230 only), period, ratio, single period, test clock, time interval, time interval delay, totalize, totalize gated, totalize gated once, & pulse width.
-
product
PXI Single 33x8 Matrix 2-Pole 1A
40-581-002
The Worlds highest density 2-pole single slot 3U PXI Matrix Module, the 40-581has 264 crosspoints configured as a 2-pole 33x8 matrix. The use of high density electromechanical relays means that the 40-581 is a low cost high density matrix solution with current handling up to 1 Amp. The 40-581 module is suitable for matrix applications where two signals are required to be switched simultaneously, for example send and return signals in a telecoms system. It is also suitable for applications where reed relay based matrices do not have sufficient power handling capability.
-
product
PXI Signal Analyzer
PXI signal analyzers provide the building blocks for your single or multichannel modular test solution with a small footprint that is scalable and flexible. With a shared processor, frame or chassis, display, and interface, you can tailor your test rack to the needs of your lab. Keysight's PXI and PXIe signal analyzers are ideal for design validation and manufacturing applications that require fast measurements, quality control, product conformance, and test optimization.
-
product
PXI RTD Simulator Module, 24 Channel, PT500
40-263-002
The 40-263-002 is a 24-channel PT500 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
product
Mounting Ear Kit, VTI Instruments, SMP 1100 Carrier
510109355
Mounting Ear Kit, VTI Instruments, SMP 1100 Carrier (for use with Part # 510109202)
-
product
PXI High Voltage Amplifiers
Pickering's PXI High Voltage Amplifiers are ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test. Each amplifier can be independently programmed to a gain of 1, 2, 5, 10 or 20, enabling it to be used with modules with low output voltage capability. Inputs and outputs can be provided either on SMB connectors or on a D Type connector to suit the user’s wiring system.
-
product
PXI Chassis
PXI Chassis are compatible with PXI, PXI Express, and PXI hybrid modules and meet the cooling requirements of the most power-demanding PXI modules. You can also choose chassis options that minimize the overall system acoustic emissions. Chassis can provide up to 18 slots, with a mixture of both PXI and PXI Express module compatibility, and you can choose between AC and DC power options.
-
product
PXI High Density Multiplexer, 5-Bank, 16-Channel, 2-Pole
40-615A-006
The 40-615A-006 is a 5-bank, 16-channel, 2-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
product
PXI Multiplexer, Dual 32-Channel, 1-Pole
40-630A-022-D/32/1
The 40-630A-022-D/32/1 is a dual 32-channel, 1-pole PXI multiplexer and is part of our series of general purpose multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
product
PXI Dual 3-Channel 10A Solid State MUX
40-666-011
The 40-666 is a high current multiplexer available in dual 3-channel or single 6-channel configurations occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive. Note: The 40-666-011 supersedes the 40-666-001 which is functionally the same but with some changes in specification. A data sheet for the 40-666-001 can be found in the40-666/667 User Manual.
-
product
3U CompactPCI Serial 2.5" SATA Storage Carrier
cPCI-A3H10
- 3U 4HP CPCI-S.0 peripheral- One 2.5" SATA 6Gb/s drive slot- Status LEDs on faceplate: drive activity, hot-swap status, user-configurable- Hot swap support- Operating temperature: -40°C to 85°C with qualified com
-
product
PXI 3A Power MUX BRIC, 5-Channel, 48-Pole
40-571-005
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
PXIe-8240, 40 Gigabit PXI Ethernet Interface Module
784977-01
40 Gigabit PXI Ethernet Interface Module—The PXIe-8240 is a high-performance 40-Gigabit Ethernet QSFP+ interface for PXI Express based on the Intel XL710 40Gb Ethernet controller. It includes two 40-Gigabit Ethernet QSFP+ ports in a single-slot PXI Express module and is compatible with both copper and fiber optic cabling.
-
product
PXI 64x2 Matrix Module, 1-Pole, 2A, 60W
40-527-001
The 40-527, 40-528A and 40-529A are PXI single-pole matrices each supporting 128 cross points. The modules are designed for switching medium voltage and power signals. The user signal connection is via a robust 78, 50 or 37 pin D-Type connector that is fully supported by the wide range of Pickering Interfaces cable and connector accessories.
-
product
PXI 16x4 Signal Insertion and Monitor Matrix
40-525A-002
This is a PXI signal insertion and monitor matrix with switched pass thru connections on both X and Y axis. It is also available in a 34x4 format and can be used for signal insertion and monitoring purposes on connections between the UUT and test system.
-
product
PXI Precision Resistor Module 3-Channel, 2.5 to 1.51M
40-297-144
This 3-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PXI Semi-Dynamic Digital I/O Module, 64-Channel
40-419-001
The 40-419-001 is a 64-channel digital I/O module suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. It can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
product
83x SPDT High-Density PXI Relay Module
40-100-001
Configured with 83 SPDT relays, this high-density 2 Amp PXI Relay module was originally designed for applications in Aerospace and Defense requiring a higher density 2 Amp alternative to our current 52 SPDT module (model 40-139). This new Relay Module is suitable for applications requiring medium power switching with very high density. It features a 2 Amp current capacity and voltages to 200VDC/140VAC.
-
product
PXI Breadboard Module, 2-Slot, 37-Pin D-Type
40-220A-202
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
product
Dual 16x2 1-Pole High-Density PXI Matrix Module
40-520-501
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
product
PXI Pull-Thru Adapter, Wired, Pickering 40-161-003
510140173
PXI Pull-Thru Adapter, Wired, Pickering 40-161-003
-
product
PXI 16 x SPDT Reed Relays
40-110-021
The 40-110/115 range of switching modules are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 96 pin male micro-D connector. General purpose reed relays are used for the construction of small switching networks or for slaving up to larger switches.To simplify inter-relay wiring, interconnection points are built onto the circuit board thus easing the construction of complicated wiring.
-
product
PXI Very High Density Multiplexer, 10-Channel, 16-Pole
40-675A-002-10/16
The 40-675A-002-10/16 is a 10-channel, 16-pole MUX and is part of our range of PXI very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
