PXI Carriers
-
Product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781259-02
Signal Module
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
Product
PXI Express Optical FPGA Board
HSS-8324
FPGA Board
The Conduant HSS-8324 Optical FPGA board provides the user with a hardware platform that is able to sustain full-duplex high-bandwidth transfers through its 8-lane Gen3 PXI Express (PXIe) interface and its 24-lane optical interface. The PXIe interface provides a theoretical maximum throughput of 8GB/s (simultaneous in and out).
-
Product
PXIe-1066DC, 18-Slot, DC Power Supply PXI Chassis
781812-01
Chassis
PXIe, 18-Slot, DC Power Supply PXI Chassis—The PXIe‑1066DC adds high-availability features to the PXI Express platform to maximize system uptime. Built on the PXIe‑1065 backplane architecture, the PXIe‑1066DC incorporates hot-swappable, redundant DC power supplies as well as hot-swappable, front-accessible, redundant cooling fans. These high-availability features improve the mean time between failure (MTBF) and mean time to repair (MTTR) of the PXI system.
-
Product
PXI FPGA & Measurement Accelerator
Measurement Accelerator
Keysight PXI FPGA & measurement accelerator provide digital-pre-distortion (DPD) and envelope tracking (ET) measurements that are embedded in high performance FPGA processing cards.
-
Product
PXI Single 32x8 Matrix, 1 Pole Screened
40-531-021-S
Matrix Switch Module
Model 40-531 very high density matrix modules are configured as a 32x8, while the 40-532 modules are configured as a Dual 16x8. Both modules are available in a choice of reed relay formats: 1-pole, 2-pole and 1-Pole screened. The screened version is suitable for switching coaxial signals up to 50MHz. Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability Sputtered Ruthenium Reed Relays, offering 109 operations to give maximum switching confidence with long life and stable contact resistance.
-
Product
PXI Solid State Switch Module, 6xSPST, 10 A
40-182A-011
Switch Module
The 40-182A-011 has 6 off high current SPST switches in two PXI slots and is part of our range of high power solid state switching solutions. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each SPST switch can support 10A of continuous current and switch up to 200V signals. The switch can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
PXI 20Amp 28Volt 2xSPDT Automotive Relay
40-181-011
Relay
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDC. The 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
-
Product
2 Amp PXI Large Matrix Modules
BRIC™
-
Our 2 Amp PXI Large Matrix Modules use high-quality electromechanical relays to achieve their 2A switch rating. The BRIC structure allows the creation of large PXI matrices over multiple slots without the use of expensive external cables. The fully integrated programming interface represents the matrix as a single entity, easing user programming and reducing the likelihood of user errors.
-
Product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781259-01
Signal Module
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
Product
PXI EMC Filler Panel Kit, 5 Slots
Y1213A
-
Provides five single-slot PXI filler panels with EMC gaskets
-
Product
PXI Versatile Multiplexer, Solid State, 350mA, 60V
40-681A-001
Multiplexer Module
The 40-681A-001 is a very high-density versatile PXI Multiplexer module featuring a wide range of selectable switching configurations with 350mA current and 60V voltage handling. The 40-681A is especially useful where a high-density MUX array is required that can adapt to different test configurations for different test targets, or where a test system may have to be reconfigured in the future.
-
Product
Tunable Laser Source - PXI
Laser 1000 Series
Laser Source
The Laser 1000 Series PXIe module is a Continuous Wave (CW), tunable laser source offering high-power output, narrow 100kHz linewidth and 0.01pm resolution tunability.With seamless PXI integration, it can be easily integrated into new or existing PXI test setups. Save space, lower your costs and improve testing efficiency while delivering reliable and repeatable results in production or research environments.
-
Product
PXI Express Data Acquisition Platform
Data Acquisition Module
PXI Express is the fastest data acquisition platform currently available with unmatched bandwidths in excess of 1 GB/s and latencies less than 1 µs. This makes PXI Express-based data acquisition systems ideal for data intensive applications like high-speed digitization, signal-generation, and communication interfaces where high sample rates and channel counts could choke other interfaces.
-
Product
PXI Precision Resistor Module 4-Channel, 2 to 102k
40-297-134
Programmable Resistor Modules
This 4-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Power Interface and Prototype PXI Card
GX7404
Interface
The GX7404 power interface board offers a low cost method for providing controlled power to UUT interface and test circuitry. The GX7404 provides +5 V, +3.3 V, +12 V, and -12 V voltage outputs which are present on the PXI motherboard to be switched through a DB25 connector for use by a UUT (unit under test) and / or interface circuitry.
-
Product
PXI Simulation Modules For Sensor Simulation
-
PXI simulation solutions for sensor simulation, including PXI Programmable Resistors—ideal for the simulation of resistive sensors and PXI Thermocouple Simulators—these provide multiple low-voltage sources ideal for simulating the operation of a thermocouple. Take a look below for all of our PXI Simulation Solutions, we also offer some of these in PCI format as well . All of our PXI simulation cards are supplied with comprehensive software drivers for Windows® XP/Vista/7/8, Lab Windows / CVI and LabView. The Pickering IVI drivers also fully support National Instruments' Switch Executive.
-
Product
PXI Load Resistor Module 10 Ohm to 2.56k
40-292-012
-
A simple solution for applications requiring a programmable load resistor with up to 15W power handling. It is able to simulate the common short circuit and open circuit conditions that can be experienced in a system due to faulty wiring or sensors.
-
Product
PXI Express Board Virtex-5 ADC Module
SMT742
-
Sundance Multiprocessor Technology Ltd.
The SMT700 is one of the first of a new range of Sundance cards that includes a direct connection to SLB (Sundance Local Bus) compatible mezzanine card, without the need for a Sundance TIM. This enables a variety of cards to be added to a system, for example extra Ethernet ports, video in/out, High speed ADC / DAC etc. Data from these extra cards (along with data from the SMT700’s own inputs – up to 1Gb/s Ethernet, 2.5Gb/s optical links, and RSL links) can be processed via the Virtex 5, or by another linked card or module.
-
Product
PXI High Density Multiplexer, 10-Bank, 8-Channel, 1-Pole
40-615A-014
Multiplexer Module
The 40-615A-014 is a 10-bank, 8-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
Product
PXI 8x2 RF Matrix 1.5GHz 50 SMA
40-750-521
Matrix Switch Module
The 40-750-521 is an 8x2 RF Matrix Module suitable for switching frequencies up to 1000MHz. It has a 50Ω characteristic impedance with front panel mounted SMA coaxial connectors. The matrix intended for the easy construction of high performance bidirectional switching systems.
-
Product
PXI Automotive Switch Simulator Modules
-
Pickering's Switch Simulator Modules are designed for automotive test applications. These modules simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. They allow automotive I/O devices to be tested for correct operation under adverse conditions.
-
Product
PXI Network Analyzers
M983xA Series
-
Keysight’s M983xA PXIe vector network analyzer (VNA) combines all your measurements into a single instrument, enabling multisite, multi-DUT, multiport system characterization with faster speeds and greater flexibility.
-
Product
PXI Synchronization Module
Module
PXI Synchronization Modules use the trigger bus, star trigger, and system reference clock features of PXI to implement advanced multi-device synchronization. By using PXI Synchronization Modules, you can improve measurement accuracy, implement advanced triggering schemes, and synchronize multiple devices to act as one for high-channel-count applications.
-
Product
PXI 2 Amp Multiplexer, Quad 8-Channel, 1-Pole
40-635A-108
Multiplexer Module
The 40-635A-108 is a quad 8-channel, 1-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXI RF Multiplexer Modules
-
Pickering's PXI RF Multiplexer Modules are capable of providing economic switching for frequencies up to 6 GHz. They are available in 50 and 75, the 75 version are designed for Telecoms and high quality video switching. Our other PXI RF options include RF SPDT switches and RF matrices. For higher frequency applications or applications requiring high performance levels, please take a look at our Microwave Switching Modules.
-
Product
PXI 4x4 20GHz Matrix with Loop-Thru & Term
40-787-528-4X4-L-T
Matrix Switch Module
The 40-787 Microwave BRIC platform is designed to provide a solution for complex RF matrix applications. Using a common mechanical platform the module can be constructed to provide scalable non-blocking or blocking microwave matrix for frequencies to at least 20GHz. The standard configurations provide up to a 4x4 matrix. More complex matrix can be constructed by adding further switching functions and other devices inside the module.
-
Product
PXI Strain Gauge Simulator Module 4-Channel, 1k
40-265-204
Strain Gauge Simulator
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 350Ω) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
PXI Dual SP6T Multiplexer 6GHz 50 SMA
40-784A-002
Multiplexer Module
Pickering Interfaces' range of 40-784A PXI Microwave Multiplexer Modules have a characteristic impedance of 50 and are capable of switching signalsup to 40GHz. Available in single, dual or triple, SP6T or SP4T formats, they are suitable for constructing complex microwaveswitching networks and provide a range of switching configurations to suit most applications. Connection is by high performancefront panel mounted SMA or SMA-2.9 connectors
-
Product
High-Voltage PXI Switching Matrix Modules
-
The design of our high-voltage PXI switching matrices ensures the modules can withstand high common mode voltages and a protective safety cover is used to shield the switching components.
-
Product
PXI 10A Power Multiplexer, 5-Bank, 6-Channel
40-661A-005
Multiplexer Module
The 40-661A-005 is a single pole, 5-bank, 6-channel PXI power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel, 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats. Also, 4-bank 4-channel, 2-bank 8-channel and 1-bank 16-channel half density configurations are available.
