-
product
FPGA Testing
Silicon Turnkey Solution, Inc.
The secret to our success in the FPGA testing field is the STS hammer file, a proprietary test methodology based on our experience testing thousands of unique FPGA designs. The hammer file is designed to program the FPGA to its maximum combination and block configuration and then tests the completely programmed FPGA for full dynamic, DC and at-speed AC performance. Power and transient tests are also conducted under worst-case populated configurations. Application-specific usage configurations are also used to assist in generating the worst-case electrical specification limits at worst-case environmental use.
-
product
24-Channel Digital I/O With Digital Integration Features On PCI Express Mini Card
mPCIe-DIO-24A
The mPCIe-DIO-24A is a type F1 PCI Express Mini Card (mPCIe) and optional cable assembly (D-Sub 37-pin Male connector) designed to be easily panel-mounted in any application environment. It uses the high speed PCI Express bus to transfer digital data to and from the card. The digital I/O is compatible with 8255 PPI chips making it easy to program. This also allows for simple and trouble-free migration from other ACCES PCI and PCI Express digital I/O cards, but also provides for advanced features enabled by the onboard FPGA logic.
-
product
Mezzanine FMC
FMC-516
Curtiss-Wright Defense Solutions
The FMC-516 provides the low latency, high-performance functionality necessary for applications such as Signal Intelligence (SIGINT), Electronic Warfare (EW) and RADAR (including beamforming) through the density, speed and resolution of data delivered to the FPGA host through the FMC-516.
-
product
8-Channel A/D & D/A Zynq UltraScale+ RFSoC Processor - QuartzXM
Model 6001
- Now available in RFSoC Gen 3 with the Model 6003- Unique QuartzXM eXpress Module enables deployment in custom form factors- Supports Xilinx Zynq UltraScale+ RFSoC FPGAs- 16 GB of DDR4 SDRAM- Measuring only 2.5 by 4 inches- LVDS connections to the Zynq UltraScale+ FPGA for custom I/O- GTY connections for gigabit serial communication- Ruggedized and conduction-cooled versions available- Includes a complete suite of IP functions and example applications- Model 8257 1-Slot 3U VPX Development Chassis for Quartz Products
-
product
L-Band RF Tuner and 2-Channel 200 MHz A/D with Virtex-6 FPGA - 6U VPX
Model 57690
- One L-Band tuners accept RF signals from 925 MHz to 2175 MHz- One programmable LNAs boost LNB (low-noise block) antenna signal levels with up to 60 dB gain- One programmable analog downconverters provide I + Q baseband signals with bandwidths ranging from 4 to 40 MHz- Two 200 MHz 16-bit A/Ds- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Up to 2 GB of DDR3 SDRAM; or: 32 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
sbRIO-9866, Non-Enclosed, 1-Port C Series LIN Interface Module
785965-01
Non-Enclosed, 1-Port C Series LIN Interface Module—The sbRIO‑9866 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The sbRIO‑9866 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals such as hardware‑in‑the‑loop (HIL) simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other DAQ measurements in the same CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same CompactRIO Chassis. Non-enclosed modules are designed for OEM applications.
-
product
CL PX4 SE Frame Grabber
Xcelera-CL PX4 SE
The X64 Xcelera-CL PX4 SE is a highly versatile PCIe frame grabber capable for one Camera Link™ Base, Medium, or Full camera and performing image transfers at rates up to 1024MB/s. Its low cost, combined with its ability to support multiple tap configurations from area and linescan monochrome/RGB cameras simultaneously; in addition to its onboard FPGA Bayer decoding and real-time shading correction makes the X64 Xcelera-CL PX4 SE an ideal solution to a wide variety of cost-sensitive applications.
-
product
FPGA Mezzanine Card
FMC407
The FMC407 is a low noise clock generation and distribution module with eight clock outputs and eight trigger outputs that are fully synchronized.There are two configurations: 34.375MHz-200MHz or 34.375MHz-4.4GHz. The FMC407 is ideal for applications that require synchronous A/D or D/A sampling across multiple cards or systems.
-
product
Programmable Logic Unit PLUS
V2495
The V2495 can be controlled and programmed “on the fly” via the VME Bus or directly through the Mini-USB connector on the front panel. A Software tool is provided for free to easily upload the custom Firmware on the User FPGA.
-
product
high-speed JTAG debugger
Bus Blaster v4
Bus Blaster is an experimental, high-speed JTAG debugger for ARM processors, FPGAs, CPLDs, flash, and more. Thanks to a reprogrammable buffer, a simple USB update makes Bus Blaster v2 compatible with many different JTAG debugger types in the most popular open source software.
-
product
OnyxFX FlexorSet 8-Channel 250 MHz A/D with DDCs - 3U VPX
Model 5973-317
- Supports Xilinx Virtex-7 VXT FPGA- GateXpress supports dynamic FPGA reconfiguration across PCIe- Eight 250 MHz 16-bit A/Ds- Eight multiband DDCs- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- Optional optical Interface for backplane gigabit serial interboard communication- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)Ruggedized and conduction-cooled versions available
-
product
C Series Serial Interface Module
The C Series Serial Interface Module adds RS232 or RS485/RS422 serial ports to CompactRIO systems. The serial ports are accessed directly from the field-programmable gate array (FPGA) to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The C Series Serial Interface Module supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions. You can choose from both enclosed and non-enclosed modules.
-
product
ARINC 818 to HDMI Converter
The ARINC 818 to HDMI converter is a rugged standalone module available in half-length PCIe form factor used for ARINC 818 to HDMI conversion, HDMI to ARINC 818 conversion, 2x ARINC 818 Switch as well as ARINC 818 Duplicator/Splitter. It is a video Converter module designed with Kintex-7 FPGA, using an Analog device Video Encoder, and Decoder to provide video interfacing requirements.
-
product
ADQ Development Kit for Custom Firmware in the FPGA of an ADQ-Series Digitizer
The ADQ Development Kit is a tool for developing custom firmware in the FPGA of an ADQ-series digitizer. SP Devices’ digitizers are characterized by a combination of high speed and high resolution.The amount of data from the digitizer is thus very high. The most efficient way of processing the data is through a real-time implementation inside the FPGA on the digitizer. The ADQ Development Kit opens the FPGA for the implementation of real-time signal processing algorithms.The ADQ Development Kit is available for all digitizer models.
-
product
CompactRIO Plug-In Chassis for I/O Modules
The plug-in chassis provides connectivity for I / O modules. The chassis core is an FPGA for reconfigurable I / O signals. Chassis are available in various configurations and are designed to accommodate 4 or 8 C-series modules.
-
product
PXIe-5745, 12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO Signal Generator
785598-02
The PXIe-5745 enables direct RF generation up to 3 GHz with 12 bits of resolution. You can use it in a dual-channel mode at 3.2 GS/s for generation up to 1.5 GHz or in a single-channel wideband upconversion mode at 6.4 GS/s. The PXIe-5745 is ideal for applications that require high channel density IF signal generation with multichannel synchronization, including radar, electronic warfare, and communications. The FlexRIO driver includes support for generating predefined waveforms, and you can use the LabVIEW-programmable Xilinx Kintex UltraScale FPGA for dynamically creating waveforms, signal modulation/demodulation, and other custom real-time signal processing.
-
product
AMC GBit link card/VITA 57 FMC carrier
SIS8100
The SIS8100 will be a single width mid height AdancedMC card. It will interface with a single PCI Express lane over a PLX Technology PEX811 PCI Express to local bus bridge chip and have an on board Virtex IV FPGA. The default stuffing option has a Small Form Factor (SFF) optical link medium that can be operated at 1, 2.5 and 4 GBit/s.
-
product
IP-QuadUART-485
The IndustryPack compatible IP-QuadUART-485 design integrates a quad UART onto an IndustryPack module. The UART (16C854) features 128 byte FIFOs for RX and TX ports on each channel. The UART is supported by an advanced IP module interface implemented within a Xilinx FPGA.
-
product
PXIe-5745, 12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO Signal Generator
785598-01
The PXIe-5745 enables direct RF generation up to 3 GHz with 12 bits of resolution. You can use it in a dual-channel mode at 3.2 GS/s for generation up to 1.5 GHz or in a single-channel wideband upconversion mode at 6.4 GS/s. The PXIe-5745 is ideal for applications that require high channel density IF signal generation with multichannel synchronization, including radar, electronic warfare, and communications. The FlexRIO driver includes support for generating predefined waveforms, and you can use the LabVIEW-programmable Xilinx Kintex UltraScale FPGA for dynamically creating waveforms, signal modulation/demodulation, and other custom real-time signal processing.
-
product
PMC Module
PMC-CIV-COM-ISO
User Programmable AlteraCyclone IV FPGA 484 BGA:• Stand alone possibility• Single wide PMC Module• 20 LVDS,2 RS-422,1 RS-232• Optional User clock oscillator
-
product
2-Channel 3.6 GHz or 4-Channel 1.8 GHz 12-bit A/D with DDC - 6U VPX
Model 58641
- Ideal radar and software radio interface solution- Two 1-Channel mode with 3.6 GHz, 12-bit A/Ds- Four 2-Channel mode with 1.8 GHz, 12-bit A/Ds- Programmable one-channel DDC (digital downconverter)- 4 GB of DDR3 SDRAM- PCI Express (Gen. 1 & 2) interface up to x8- µSync clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
product
NI-9853, CAN Interface Module
780178-01
2-Port, High-Speed C Series CAN Interface Module—The NI‑9853 is a high-speed Controller Area Network (CAN) interface for developing FPGA-based applications with the NI‑RIO driver on CompactRIO. The NI‑9853 is ideal for low-level FPGA‑based control and triggering applications that are programmed using the LabVIEW FPGA Module. The NI‑9853 is ideal for byte-level manipulation of CAN frames using the LabVIEW FPGA Module. The NI‑9853 is only compatible with CompactRIO systems.
-
product
6-slot PXIe Chassis
PXCe4006
6-slot PXI Express chassis1 system slot, 1 PXI Express slot and4 PXI/PXI Express full hybrid peripheral slotsOptional: complex FPGA trigger controller with8 freely configurable trigger IOs on the rear sideVery compact 1U 19" designFour link PXI Express chassisEasily replaceable fan unit
-
product
2-Ch 500 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Virtex-6 FPGA - XMC
Model 71651
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Two 500 MHz 12-bit A/Ds- Two multiband DDCs (digital downconverters)- Two 800 MHz 16-bit D/As- One DUC (digital upconverter)- Multiboard programmable beamformer- Up to 2 GB of DDR3 SDRAM or 16 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- Front panel clock/sync bus for multimodule synchronization- PCI Express (Gen. 1 & 2) interface up to x8- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
PCIe/104 OneBank SBC w. Dual 1GHz ARM9 & 1Gbyte DDR3
EMC²-Z7015
Sundance Multiprocessor Technology Ltd.
The EMC²-Z7015 is a PCIe/104 OneBank™ SBC with a Xilinx Zynq SoC, Artix-7 FPGA fabric and a VITA57.1 FMC™ LPC I/O board. The main processing power of the EMC²-Z7015 is a Dual Core ARM9 and combined with traditional FPGA fabrics/gates + High-Speed I/O interfaces, like USB2.0, HDMI, 1Gb Ethernet and SATA and provide an total solution for any Embedded Application.
-
product
PXIe-7912, KU040 FPGA, 4 GB DRAM, x8 Gen 3 PXI Coprocessor Module
785173-01
The PXIe-7912 provides a Xilinx Kintex UltraScale FPGA that you can program with LabVIEW or Xilinx Vivado to add signal-processing capabilities to PXI Express systems. Using the x8 Gen 3 PCI Express architecture and peer-to-peer streaming, PXI FlexRIO Coprocessor Modules can stream data to and from other modules in a PXI chassis at up to 7 GB/s without a host controller. You can pair these modules with another PXI instrument, such as a PXI Vector Signal Transceiver, to add functionality, such as running complex algorithms in real-time. The PXIe-7912 KU040 FPGA is ideal for applications that require a moderate amount of signal processing.
-
product
cRIO-9032, 1.33 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, Kintex-7 160T FPGA, WiFi, 4-Slot CompactRIO Controller
784548-01
1.33 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, Kintex-7 160T FPGA, WiFi, 4-Slot CompactRIO Controller - The cRIO-9032 is a rugged, fanless, embedded controller that you can use for advanced control and monitoring applications. This software-designed controller features an FPGA, a real-time processor running the NI Linux Real-Time OS, and embedded user interface capability. You also can use the Mini DisplayPort to add a local human machine interface (HMI) for application development. The cRIO-9032 also features dual-band, 802.11 a/b/g/n WiFi communication to help you connect to HMIs, the cloud, and other devices. Additionally, the cRIO-9032 features an SDHC slot and a variety of connectivity ports, including two tri-speed RJ-45 Gigabit Ethernet, two USB host, one USB device, and two RS-232 serial. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
product
1-Chan 3.6 GHz or 2-Chan 1.8 GHz 12-bit A/D with Virtex-6 FPGA - PCIe
Model 78640
Model 78640 is a member of the Cobalt® family of high performance XMC modules based on the Xilinx Virtex-6 FPGA. A highspeed data converter, it is suitable forconnection to HF or IF ports of a communications or radar system. Its built-in data capture features offer an ideal turnkey solution as well as a platform for developing anddeploying custom FPGA processing IP.
-
product
Development Kit
The VP430 is 3U VPX RF processing system featuring the transformational Xilinx® Zynq® Ultrascale+™ RF system-on-chip technology (RFSoC). The ZU27DR device used on the VP430 includes eight integrated analog-to-digital converters at 4GSPS, eight digital-to-analog converters at 6.4 GSPS, a user-programmable FPGA fabric, and multi-core Zynq ARM® processing subsystem.
-
product
Multi-Channel 1553 Interface for Single Lane PCI Express Systems
PCIE1L-1553
Alta Data Technologies’ PCIE1L-1553 interface module is a multi-channel (1-2), ½ size, Low Profile, One Lane PCI Express 1553 card with the latest software technologies. The PCI Express card is based on the industry’s most advanced 32-bit 1553 FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET) architecture. This package provides increased system performance and reduces integration time.
