Microwave Synthesizers
See Also: Rf Frequency Synthesizers
-
product
Microwave Switch Cards
The Adapt-a-Switch® microwave switch cards deliver high performance and high density for your microwave switching applications.
-
product
Low Cost Microwave Wideband APD Preamp Receivers
MR11 (40KHz~18GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
MR11 series microwave wideband optical receiver, adopts high Sensitivity APD diode and Low Noise Preamplifier IC, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave-guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s high speed communication system.
-
product
Multifrequency Clock Synthesizer - PMC
Model 7190
- Simultaneous synthesis of up to 5 different clocks- 8 SMC clock outputs- Ideal for A/D and D/A converter clock sources- Typical phase noise: -125 dBc/Hz @ 1 kHz offset- All clocks are phase-locked to input reference signal- Input reference frequency of 5 or 10 MHz- Four quad VCXOs allow selection from 16 different base frequencies- Output clocks of 1, 2, 4, 8, or 16 submultiples of VCXO base frequencies- Output clock frequencies between 50 and 500 MHz- Control and status via PCI bus interface
-
product
Microwave Leakage Detector
*Microwave leakage detection:≥ 1mw/cm2*Meter points to show "SAFETY" or "DANGER" zone*No battery required*Dimension (LxWxD) mm : 53x36x23*Packaging: Sliding blister card
-
product
Microwave Relays
CXM/2x2
CXM/2x2-F-SMA Microwave Relays have a Normally Closed (NC = OFF) and Normally Open (NO = ON) Position as shown in the drawing on the left. They can also be used as a terminated 2x1 relay. Usefull for swapping signals between devices, reversing signal flow or interfacing to larger configurations. Specifications Bandpass DC to 18 GHz Insertion Loss 0.3 dB @1 GHz, 0.8 dB @ 18 GHz VSWR 1.2:1 @ 1 GHz, 1.5:1 @ 18 GHz Isolation -80 dB @ 1 GHz, -60 dB @ 18 GHz
-
product
LXI Microwave Matrix, 10GHz, Single 8x4
60-750-184-B
The 60-750-184-B is a single 8x4 10GHz microwave matrix with internal termination. It is part of the 60-750/751 range of LXI Microwave Switches controlled through an LXI compliant Ethernet connection. It is available in a variety of configurations and frequencies up to 18GHz (60-751). The matrix is characterized for 50 ohm applications, for 75 ohm versions please consult your local sales representative.
-
product
Microwave and RF Switching Systems and Drivers
CXM Series
This series is typically used for frequencies from DC to 40 GMHz. We use microwave relays, splitters, programmable attenuators and many other microwave components from the worlds most popular vendors to build standard or custom systems to your specifications. There are a large variety of 1x2 through 1x12 microwave relays available in Normally Open, Failsafe, Latching, Terminated or special configurations to suit your needs. Or simply buy the driver chassis and use it to control your own components. Since Cytec doesn"t build microwave components we can put the systems together with whatever parts you prefer and stand behind the warranty for you.
-
product
PXI/PXIe Microwave Multiplexer, Single SP4T, 40GHz, 50Ω, SMA-2.9
40-784B-141
The 40-784B-141 (PXI) and 42-784B-141 (PXIe) are single SP4T 40GHz unterminated microwave multiplexers. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
product
RF Synthesizers Modules
Holzworth Instrumentation, Inc.
Holzworth's RF Synthesizers Modules were originally designed as the internal, tunable LO test sources for Holzworth phase noise analyzer products. Due to the need for easy integration, the HSM Series designs incorporate a long list of electrical and mechanical features to satisfy the demanding requirements of today's high performance communications systems and integrated test systems. FIELD PROVEN RELIABLITY with MTBFs exceeding 240kHrs.
-
product
PXI Dual Microwave Transfer Switch 18GHz 50 SMA
40-782A-522
The 40-782A-522 is a dual transfer switch and is part of our range of PXI microwave switching modules. It has a characteristic impedance of 50Ω and a maximum operating frequency of 18GHz. Connections are made via front panel mounted high quality SMA coaxial connectors.
-
product
LXI Microwave Multiplexer, SP4T, 16-Bank, 67GHz, 50Ω, SMA-1.85
60-803-816
Our 60-803-816 is a 16 bank SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-803 range is capable of supporting up to 16 banks of 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
PXI/PXIe Microwave Multiplexer, Dual SP4T, 50GHz, 50Ω, SMA-2.4
40-785C-452-T
The 40-785C-452-T (PXI) and 42-785C-452-T (PXIe) are dual SP4T 50GHz microwave multiplexers with automatic termination of unused signals. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
product
Microwave Monitor + Power Check Kit
A100c
This single-range, RF power measurement instrument is designed to operate in the 2.45 GHz range. Used by field service engineers, engaged in the repair and maintenance of commercial and domestic microwave heating equipment, its primary function is the detection RF microwave energy leakage.
-
product
LXI Microwave Multiplexer, 50Ω 6-Channel 2-Bank 6GHz SMA
60-801-002
The 60-801-002 is a 6-channel, 2-bank RF multiplexer suitable for switching 50Ω signals up to 6GHz. It is part of a range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for between 1 and 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
LXI Microwave Multiplexer, SP4T, 7-Bank, 50GHz, 50Ω, SMA-2.4
60-803-707
Our 60-803-707 is a 7 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
PXI/PXIe Microwave Multiplexer, Single SP4T, 18GHz, 50Ω, SMA
40-784B-121
The 40-784B-121 (PXI) and 42-784B-121 (PXIe) are single SP4T 18GHz unterminated microwave multiplexers. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
product
PXI Single Microwave SPDT Relay 2.5GHz 75 1.6/5.6
40-780A-751
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options).
-
product
PXI/PXIe Microwave Multiplexer, Single SP6T, 3GHz, 50Ω, N-Type
40-785C-561
The 40-785C-561 (PXI) and 42-785C-561 (PXIe) are single SP6T 3GHz unterminated microwave multiplexers. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
product
LXI Microwave Multiplexer, SP4T, 1-Bank, 18GHz, 50Ω, SMA
60-803-101
Our 60-803-101 is a 1 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 18GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
PXI/PXIe Microwave Multiplexer, Triple SP4T, 40GHz, 50Ω, SMA-2.9
40-784B-143
The 40-784B-143 (PXI) and 42-784B-143 (PXIe) are triple SP4T 40GHz unterminated microwave multiplexers. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
product
LXI Microwave Matrix, 20GHz, Single 3x3 With Loop-Thru
60-751-133-A
The 60-751-133-A is a single 3x3 20GHz microwave matrix with loop-thru. It is part of the 60-750/751 range of LXI Microwave Switches controlled through an LXI compliant Ethernet connection. It is available in a variety of configurations and frequencies up to 20GHz (60-751). The matrix is characterized for 50 ohm applications, for 75 ohm versions please consult your local sales representative.
-
product
FieldFox Handheld Microwave Analyzer, 14 GHz
N9916B
A lightweight, durable, cable and antenna analyzer, spectrum analyzer, network analyzer, and more
-
product
PXI/PXIe Microwave Relay, Quad SPDT, 67GHz, 50Ω, SMA-1.85
40-780B-574
The 40-780B-574 (PXI) and 42-780B-574 (PXIe) are quad SPDT 67GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67GHz in 50Ω or 2.5GHz in 75Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75Ω versions.
-
product
LXI Microwave Multiplexer, 50Ω 4-Channel 10-Bank 26.5GHz SMA
60-802-310
The 60-802-310 is a 4-channel, 10-bank RF multiplexer suitable for switching 50Ω signals up to 26.5GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
LXI Microwave Matrix
60-891-006
The 60-891-006 is a compact 50 Ω microwave switching matrix with added loop-back functionallity and a maximum bandwidth of 18 GHz. It is ideal for constructing complex microwave switching systems for many applications.
-
product
FieldFox Handheld Microwave Analyzer, 9 GHz
N9915B
Keysight's FieldFox portable analyzers are equipped to handle your toughest working environments during routine maintenance, in-depth troubleshooting, and anything in between.
-
product
Microwave Devices
Photonis Defense and its predecessors have been designing and manufacturing Traveling Wave Tubes (TWTs) since their invention in the early 1940’s. Photonis manufactures helix-type tubes that are constructed using the industry standard metal-ceramic construction. Our tubes are conduction cooled and feature rare earth periodic permanent magnets for power-free focusing.
-
product
LXI Microwave Multiplexer, SP4T, 5-Bank, 50GHz, 50Ω, SMA-2.4
60-803-705
Our 60-803-705 is a 5 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
FieldFox Handheld Microwave Analyzer, 26.5 GHz
N9918B
A lightweight, durable cable and antenna analyzer, spectrum analyzer, network analyzer, and more.
-
product
LXI Microwave Multiplexer, 50Ω 6-Channel 10-Bank 6GHz SMA
60-801-010
The 60-801-010 is a 6-channel, 10-bank RF multiplexer suitable for switching 50Ω signals up to 6GHz. It is part of a range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for between 1 and 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
