Microwave Synthesizers
See Also: Rf Frequency Synthesizers
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 8-Bank 40GHz SMA-2.9
60-802-408
Multiplexer Module
The 60-802-408 is a 4-channel, 8-bank RF multiplexer suitable for switching 50Ω signals up to 40GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
High Power Microwave Plasma System
-
The High Power Microwave Plasma System features the High Power Microwave Plasma Source, generator (with isolator) and auto-tuning system comprised of the Precision Power Detector and SmartMatch® unit. This comprehensive system delivers a high concentration of radicals with low electron temperatures for the highest dissociation and lowest recombination rates.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP6T, 50GHz, 50Ω, SMA-2.4
40-785C-552
Multiplexer Module
The 40-785C-552 (PXI) and 42-785C-552 (PXIe) are dual SP6T 50GHz unterminated microwave multiplexers. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXI Single Microwave SPDT Relay 40GHz 50 SMA-2.9
40-780A-541
Relay
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options).
-
Product
FieldFox Handheld Microwave Spectrum Analyzer, 14 GHz
N9936A
Spectrum Analyzer
100 kHz to 14 GHz frequency range Expand capabilities with optional tracking generator, interference analyzer, built-in power meter, and more Make accurate spectrum analyzer measurements ( 0.5 dB) without needing warm-up Locate interfering signals using the intuitive spectrogram display and recording capability Easily measure average and pulse power with a USB power sensor, pulse measurements with time gating Lightest microwave handheld spectrum analyzer at only 6.6 lb. (3.0 kg)
-
Product
RF & Microwave Power Meters
-
Our RF & microwave power sensors ensure precise and reliable measurements. They provide the highest measurement accuracy and speed, simple operation, technological leadership in thermal, diode and OTA core measurement elements as well as traceability to national standards.
-
Product
LXI Microwave Multiplexer, SP4T, 12-Bank, 18GHz, 50Ω, SMA
60-803-112
Multiplexer Module
Our 60-803-112 is a 12 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 18GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 11-Bank 26.5GHz SMA
60-802-311
Multiplexer Module
The 60-802-311 is a 4-channel, 11-bank RF multiplexer suitable for switching 50Ω signals up to 26.5GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
RF & Microwave Modules for 34980A
-
The Keysight RF and Microwave multiplexer modules for the 34980A Multifunction Switch/Measure Unit offer broadband switching capabilities for switching from DC to 26.5 GHz. Use these modules to route test signals between your device under test and your signal generator, oscilloscope, spectrum analyzer, or other instrumentation. A switch/attenuator driver module also allows control of switches and attenuators external to the 34980A Mainframe.
-
Product
FieldFox Handheld Microwave Vector Network Analyzer
N9928A
Vector Network Analyzer
26.5 GHz max frequency Carry the world's most integrated handheld T/R VNA analyzer Expand your measurement flexibility with optional 2-port VNA, time-domain, vector voltmeter, cable and antenna analyzer and more Save time by simultaneously measuring all four S-parameters with a single connection Perform accurate testing with QuickCal, full 2-port unknown thru Cal, TRL Easily measure average and pulse power with a USB power sensor
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 7-Bank 40GHz SMA-2.9
60-802-407
Multiplexer Module
The 60-802-407 is a 4-channel, 7-bank RF multiplexer suitable for switching 50Ω signals up to 40GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
Microwave Wideband Synthesizer w/ Integrated VCO
ADF5356
-
The ADF5356 allows implementation of fractional-N or integer-N phase-locked loop (PLL) frequency synthesizers when used with an external loop filter and an external reference frequency. The wideband microwave VCO design permits frequency operation from 6.8 GHz to 13.6 GHz at one radio frequency (RF) output. A series of frequency dividers at another frequency output permits operation from 53.125 MHz to 6800 MHz. The ADF5356 has an integrated VCO with a fundamental output frequency ranging from 3400 MHz to 6800 MHz. In addition, the VCO frequency is connected to divide by 1, 2, 4, 8, 16, 32, or 64 circuits that allow the user to generate RF output frequencies as low as 53.125 MHz. For applications that require isolation, the RF output stage can be muted. The mute function is both pin- and software-controllable.
-
Product
PXI Triple Microwave SPDT Relay 18GHz 50 SMA
40-780A-523
Relay
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options).
-
Product
LXI Microwave Multiplexer, SP6T, 3-Bank, 67GHz, 50Ω, SMA-1.85
60-800-803
Microwave Multiplexer
Our 60-800-803 is a 3 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
Low Cost Microwave Wideband APD Preamp Receivers
MR11 (40KHz~18GHz)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
MR11 series microwave wideband optical receiver, adopts high Sensitivity APD diode and Low Noise Preamplifier IC, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave-guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s high speed communication system.
-
Product
Microwave Relays (SP3T to SP12T)
CXM/3x1 to CXM/12x1
-
CXM/3x1 to 12x1-NO-SMA Microwave Relays are Normally Open (NO) in the OFF state. Only one port can be on at a time. Larger configurations can be built by connecting the common port of multiple relays to another relay in series.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 4-Bank 18GHz SMA
60-802-204
Multiplexer Module
The 60-802-204 is a 4-channel, 4-bank RF multiplexer suitable for switching 50Ω signals up to 18GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
FieldFox Handheld Microwave Spectrum Analyzer, 6.5 GHz
N9934B
Spectrum Analyzer
A lightweight, durable, microwave spectrum analyzer, interference analyzer, distance-tracking generator, preamplifier, power meter, and more.
-
Product
Microwave Digestion
-
Superior trace elemental analysis begins with outstanding sample preparation. With over 40 years of experience, Anton Paar strives to make microwave digestion easier and more convenient than ever before – thanks to sophisticated instrument and vessel concepts, state-of-the-art sensor technology, and the highest safety standards. Anton Paar offers the broadest range of instruments for all kinds of applications: microwave digestion systems Multiwave 7000 and Multiwave GO Plus, the microwave reaction platform Multiwave 5000 and conventionally heated Multicube 48.
-
Product
Microwave System Amplifier, 2 GHz To 8 GHz
87415A
Amplifier
The Keysight 87415A microwave component amplifier brings compact, reliable gain block performance to systems integrators and microwave designers. With 25 dB minimum gain and over 23 dBm output power from 2 to 8 GHz, this amplifier offers output power where it is needed: at the test port.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 3-Bank 6GHz SMA
60-802-003
Multiplexer Module
The 60-802-003 is a 4-channel, 3-bank RF multiplexer suitable for switching 50Ω signals up to 6GHz. It is part of a range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for between 1 and 16 banks of 4 or 6-channel multiplexers.
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 1-Bank 40GHz SMA-2.9
60-801-401
Multiplexer Module
The 60-801-401 is a 6-channel, 1-bank RF multiplexer suitable for switching 50Ω signals up to 40GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
LXI 50Ω Microwave Matrix
60-807-010-002
-
The 60-807 Microwave Matrix is suitable for routing 50 Ω signals up to 67 GHz. With sizes up to 12x12 it is ideal for constructing complex microwave switching systems for many applications (other sizes are available on request). Connection is by front panel mounted SMA. SMA 2.9, SMA 2.4, SMA 1.85 or N-type connectors.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 12-Bank 26.5GHz SMA
60-802-312
Multiplexer Module
The 60-802-312 is a 4-channel, 12-bank RF multiplexer suitable for switching 50Ω signals up to 26.5GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
PNA-X Microwave Network Analyzer, 26.5 GHz
N5242B
Network Analyzer
Simplify your test stations by replacing racks and stacks of equipment Increase productivity with the most integrated and flexible single-connection microwave test engine Reduce test time with the world's widest range of single-connection measurement applications Accurately test linear and nonlinear device characterization using advanced error correction Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
Microwave Coaxial Cable Assemblies
MWX0 series
-
JUNFLON® MWX products are flexible signal transmission lines that take advantage of the remarkable properties of fluoropolymers. They are suitable for use with a wide range of frequencies up to 67 GHz. These products feature low insertion loss and low VSWR, low signal leaks and low interference due to high shielding effectiveness, and higher density wiring for use in the narrow device interiors. Junkosha provides highly reliable products for microwave /millimeterwave applications tailored to customer assembly needs.
-
Product
RF And Microwave Accessory Kit
N9311X
-
N9311X RF and Microwave Accessory Kit complements Keysight's low-cost handheld and benchtop solutions. These accessories provide you with a complete solution when using Keysight handheld and low-cost benchtop solutions for your measurement needs.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP4T, 40GHz, 50Ω, SMA-2.9
40-785C-441
Multiplexer Module
The 40-785C-441 (PXI) and 42-785C-441 (PXIe) are single SP4T 40GHz unterminated microwave multiplexers. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
LXI Microwave Multiplexer, SP4T, 2-Bank, 26.5GHz, 50Ω, SMA
60-803-302
Multiplexer Module
Our 60-803-302 is a 2 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
