Interface Devices
soft and hard handshake between devices.
-
product
Connected Devices
enable communication between devices. We provide connectivity for sensor applications and input devices via mobile communication and develop custom IoT solutions. Capturing, transferring and visualizing data increases your productivity and creates transparency.
-
product
3 Port Devices
Teledyne Lincoln Microwave supplies 3 port circulators and isolators that operate from UHF to V Band. They are available in a range of different packages; planar microstrip, coaxial and waveguide.
-
product
GPIB Digital Interfaces
All of ICS's GPIB Digital Interfaces are user configurable and let you transfer data as bits, bytes or as strings of bytes. All data lines are high power TTL outputs or floating inputs with pullup resistors for sensing CMOS signals or switch contacts. All interfaces conform to the IEEE-488.2 Standard and are HP-IB compatible.
-
product
Serial Digital Interface
Model 2363
* Provides 48 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes or data strings.* RS-232 and RS-485 Serial IO.* 1 U high rack mount kit mounts one or two 2363s* Includes US 115 VAC Power Adapter
-
product
Measuring Devices For Nanoindentation
With our measuring devices, you can determine the mechanical properties of thin coatings reliably and accurately. From protective paint coatings to hardness of PVD coatings: We have the right solution for you. We offer you powerful and easy-to-use measuring instruments for the laboratory and production. You can choose from a wide range of accessories to adapt your device to your individual requirements.
-
product
Circuit Breaker Simulation Device
PSS01
PSS01 is the circuit breaker simulator，which can conduct circuit breaker simulation to test the whole secondary relay scheme together with relay test set. It is very good accessory for protection relay test kit to avoid complicated software programming to finalize the same test.
-
product
Smart Device Testing
Helping you ensure that your smart devices with integrated wireless modules meet requirements to demonstrate compliance to global wireless type approval requirements.A smart device is any piece of electronic equipment that intentionally communicates and interacts with other electronic devices using wireless protocols. In order to verify the performance and connectivity of these devices, both the device hardware and the communication protocol are evaluated to ensure smooth connectivity and eliminate unacceptable interference.
-
product
Intelligent Interface Card
IIB-1553-PC104+
The IIB-1553-PC104+ is an intelligent interface card giving full MIL-STD-1553 test, simulation and bus analysis capability on the PC104+ bus, providing 1553A, 1553B, McAir and STANAG 3838 variants in a single card. The IIB-1553-PC104+ supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a variable amplitude dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
product
GPIB Printer Interfaces
ICS's GPIB to Printer Interfaces are GPIB and HP-IB compatible. Replaces obsolete GPIB plotters and printers with a modern printer or copies the print file to your PC.
-
product
VME Controller With USB-2 Interface
VM-USB
The VM-USB is a VME master with high speed USB2 interface. Enhanced functionality is given by the programmable internal FPGA logic which provides a VME command sequencer with 4kB stack and 28kB data buffer. Combined with the 4 front panel I/O ports this allows VME operation and data acquisition / buffering without any PC or USB activity.
-
product
Radiation Survey Device
DRG-T
The DRG-T radiation survey device is designed for use in special-purpose vehicles for continuous control and measurement of exposure dose rate (EDR) of gamma and X-ray radiation, as well as for providing audio and visual alarm of its dangerous levels and for issuing commands to start the actuators of protection equipment.
-
product
PXIe-6592, 10 Gbps, 4-Channel PXI High-Speed Serial Instrument
783639-01
10 Gbps, 4-Channel PXI High-Speed Serial Instrument—The PXIe‑6592 is designed for engineers who need to validate, interface through, and test serial protocols. It includes a Xilinx Kintex‑7 FPGA to implement various high-speed serial protocols, and it is programmable in LabVIEW FPGA for maximum application-specific customization and reuse. The PXIe‑6592 takes advantage of FPGA multigigabit transceivers and up to four TX and RX lanes.
-
product
Hall Sensor Board with I2C Interface
056-742
Version: +5V/60A +3,3V/60A +12V/90A -12V/5A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
product
Digital Serial Data Audio Interface
PIO-9216
For accurate testing of devices that use the I2S, Left Justified, Right Justified and TDM audio data formats.
-
product
Interface Adapter
U2C-12
Dimax U2C-12, all-in-one USB-I2C, USB-SPI and USB-GPIO Bridge device, converts PC USB transactions to the I2C Master, SPI Master transactions and GPIO functions. U2C-12 turns your PC running Windows, Linux or MacOS into comprehensive I2C/SPI Bus master.
-
product
Digital Interface
DNTBOB-88
BOB 88 is a high quality, general purpose interface to transmit and receive line level analog audio signals via a Dante network. Analog inputs are converted to digital and appear on the network as transmit channels. Audio for the analog outputs is taken from subscriptions to transmit channels on the network from other sources. When connected to a network, each break out box will appear as a separate device in the Dante Controller software interface.
-
product
Test Devices
qCf - quickCONNECT - efficient, accurate, safe!Measurements on internal components of the fuel cell and electrolysis
-
product
Series Resonance Test Devices
Wuhan Huatian Electric Power Automation Co., Ltd.
Voltage capacitance testers by HVTEST
-
product
Wire Damage Test Device For Pull Testing
IEC60884 FIG11
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 FIG11 Wire damage test device for pull testingThe wire damage test device is a special test instrument designed and manufactured according to the requirements of IEC884 Figure 11, , etc. It is mainly used to judge whether the screw-clamp type terminal is in design and structure.
-
product
Device Current Waveform Analyzers
The dedicated Current Sensors measure from 100 pA level dynamic current up to 10 A with a maximum of 200 MHz bandwidth. The mainframe acquires the signal from the sensors by a maximum of 1 GSa/s sampling speed and 14-bit and 16-bit wide dynamic range. This combination allows you to measure quite wide range of dynamic current, for example, from standby/sleep state to active state, at a single measurement. In addition, the wide bandwidth and the high speed acquisition enable you to measure high speed pulse response even less than 100 ns previously very difficult with existing instruments.
-
product
Industrial Ethernet Physical Layer Devices
The ADI Chronous™ Industrial Ethernet physical layer (PHYs) portfolio includes solutions for standard 10 Mbps, 100 Mbps, and 1 Gbps. It also features the new 10BASE-T1L technology for single-pair Ethernet.Our industry-leading low latency and low power PHY technology maximizes data transmission and signal integrity in deterministic applications by reducing cycle times and system power consumption. It enables superior synchronization of signals across the industrial network and supports the development of TSN.
-
product
KYK-13 Interface
IP-Crypto
The IP Crypto is a special version of the IP-Parallel-HV. The basic design features are retained and an interface to a KYK-13 is provided. The original KYK-13 interface uses the 6.5V reference output, a transfer request output, and 3 inputs for clock, data and switch. The outputs for the general purpose section are reduced to 23 in number. The inputs are all available through the filter or after processing by the KYK-13 interface.
-
-
product
CAN interfaces and Analysers
CAN interfaces and analyzers with easy to use CAN bus software with optional support for OBDII, J1939, XCP/CCP, CAN transmit, and reading of DBC files.
-
product
Industrial Electronics Testing for Smart Devices & More
As more and more devices are being designed with inherent intelligence and the ability to connect and communicate, the amount and complexity of electronic content is continuously increasing for our industrial customers. They need the ability to quickly and efficiently verify proper operation of these products as they flow off the production line. Circuit Check responds to these needs by offering a wide range of industrial electronics testing solutions from consulting to complete test system and software design. We also offer adaptable support solutions to ensure proper equipment operation throughout its life cycle.
-
product
CAN/FlexRay/Differential Bus PXI Fault Insertion Switch - 4 Channel
40-200-004
Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signaling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
product
Universal Measuring Device For Magnetic Fields
Teslameter M-Test MK4
The M-Test MK4 precisely detects and measures static or dynamic magnetic fields. The ~ 1 mm thick tangential probe allows precise, punctual measurements in hard-to-reach places, air gaps or on surfaces. The M-Test MK4 is particularly suitable for measuring permanent magnets or small ferromagnetic parts.
-
product
PC/104 8-Channel Smart Sensor Interface
518
Measures thermocouples, RTDs, strain gages, thermistors, 4-20 mA, voltage and resistance 8 high-accuracy differential input channels Integral sensor excitation Exclusive pulsed excitation minimizes sensor self-heating Configurable sensor type per channel Fully electronic calibration Low power
-
product
Test Tool for Modern Wireless Communication Devices
ITN 1000 for WLAN and Bluetooth™
Functional Test Tool for Modern Wireless Communication DevicesDevelopment, prototyping, validation and production testing of wireless devices supporting the Internet of Things need low cost, easy-to-use test equipment with support for the latest standards:- Wi-Fi 6E: 802.11ax, 2×2 MIMO; 2/5/6 GHz - Bluetooth™: 5.2 BDR/EDR/BLE
-
product
PCI-6602, 5 V, 8-Channel Counter/Timer Device
777531-01
The PCI‑6602 performs encoder position measurements, event counting, period measurement, pulse-width measurement, pulse generation, pulse-train generation, and frequency measurement. It features eight counter/timers, digital debouncing filters, … and TTL/CMOS-compatible digital I/O. The PCI‑6602 can perform three simultaneous high-speed DMA transfers.
