Trigger Modules
-
Product
PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer
781426-02
Signal Module
Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.
-
Product
PXIe-6672, TCXO PXI Synchronization Module
780063-01
Synchronization Module
PXIe, TCXO PXI Synchronization Module—The PXIe‑6672 is a system timing controller module. It can drive the PXI star trigger lines, import and export PXI backplane clocks and triggers, generate a high-resolution direct digital synthesis (DDS) clock, and generate a high-stability temperature-compensated crystal oscillator (TCXO) 10 MHz Reference Clock for instrumentation. The PXIe‑6672 allows you to synchronize multiple PXI Express systems, synchronize a PXI Express system with external instruments and equipment, and increase the accuracy of instruments within a PXI Express system.
-
Product
NI-9423, 24 V, 8 Channel (Sinking Input), 1 µs C Series Digital Module
783735-01
Digital Module
24 V, 8 Channel (Sinking Input), 1 µs C Series Digital Module - The NI‑9423 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with 24 V logic levels, can accept up to … 30 V discrete logic levels, and has an LED that indicates the status. The NI‑9423 offers isolation between the input and output banks from channel to earth ground. The NI‑9423 is a correlated digital module, so it can perform correlated measurements, triggering, and sychronization when installed in a CompactDAQ chassis.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 14-Bank 18GHz SMA
60-802-214
Multiplexer Module
The 60-802-214 is a 4-channel, 14-bank RF multiplexer suitable for switching 50Ω signals up to 18GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
LXI 8:1 Optical MUX SC/PC Loop-Thru
60-850-221
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
Quad 4 To 1 Terminated 50Ω 600MHz PXI RF Multiplexer
40-761A-004
Multiplexer Module
The 40-761A-004 terminated quad 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
LXI 8:1 Optical MUX FC/APC Single Mode
60-850-011
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 62.5/125 Fiber, ST Connectors, With Interlock
42-850A-514-M62.5-HI
Multiplexer Module
The 40/42-850A-514-M62.5-HI is a PXI/PXIe 4-channel multiplexer with ST connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 9-Bank 40GHz SMA-2.9
60-802-409
Multiplexer Module
The 60-802-409 is a 4-channel, 9-bank RF multiplexer suitable for switching 50Ω signals up to 40GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
PXI Breadboard Module, 1-Slot, 25-Pin D-Type
40-220A-301
Signal Module
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
Product
PXI/PXIe MEMS Optical Switch, Single Insert/Bypass
40-860A-212
Multiplexer Module
The 40/42-860A-212 is a PXI/PXIe single insert/bypass switch with SC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
PXI/PXIe RF Multiplexer, Single 16-Channel, 3GHz, 50Ω, SMB
40-875A-001
Multiplexer Module
The 40-875A-001 (PXI) and 42-875A-001 (PXIe) are single 50 Ohm 16-channel RF multiplexers in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
Product
LXI Microwave Multiplexer, SP4T, 14-Bank, 18GHz, 50Ω, SMA
60-803-114
Multiplexer Module
Our 60-803-114 is a 14 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 18GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP8T, 26.5 GHz, 50 Ω, SMA, Terminated, Remote Mount, Failsafe
40-788-042-TE
Multiplexer Module
The 40-788-042-TE (PXI) and 42-788-042-TE (PXIe) are dual failsafe SP8T 26.5 GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-788 range of multiplexers are also available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 11-Bank 18GHz SMA
60-802-211
Multiplexer Module
The 60-802-211 is a 4-channel, 11-bank RF multiplexer suitable for switching 50Ω signals up to 18GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
Signal/Micro Power/ Micro Coax, Module, Receiver, QuadraPaddle, iCon Series, 100/15 Position, loaded w/ twin female contacts & round posts
510160113
Receiver Module
This module comes fully loaded with twin female contacts & round posts (p/n's 610138200 & 610138117).iCon modules mount from the rear of the iCon/i1 receiver and ITA and allow installation and removal of pre-wired cable blocks. Primary mating module 510161107. (May mate with other ITA modules, as well.)
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP6T, 18 GHz, 50 Ω, SMA, Remote Mount, Failsafe
42-785C-522-E
Multiplexer Module
The 40-785C-522-E (PXI) and 42-785C-522-E (PXIe) are dual failsafe SP6T 18 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP4T, 40 GHz, 50 Ω, SMA-2.9, Terminated, Remote Mount, Failsafe
42-785C-441-TE
Multiplexer Module
The 40-785C-441-TE (PXI) and 42-785C-441-TE (PXIe) are single failsafe SP4T 40 GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
Module, Receiver, RTCASS, Power, 40/36 Position
510113141
Receiver Module
Module, Receiver, RTCASS, Power, 40/36 Position.
-
Product
C Series Temperature Input Module
Module
The C Series Temperature Input Module features up to 16 channels of temperature input from either thermocouples or RTDS. This module can include anti-aliasing filters, open-thermocouple detection, and cold-junction compensation. Additionally, the module also feature isolation for safety, noise immunity, and high common-mode voltage range.The C Series Temperature Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
600 Watt Electronic Load Module
N3306A
Load Module
The Keysight N3306A is a 600 W (0-120A, 0-60V) electronic load module for use in either the N3300A or N3301A electronic load mainframe in system applications. The N3306A load module is fast and accurate, for programming in constant current, constant voltage, or constant resistance modes, or for making voltage, current or power measurements. The N3306A can also digitize waveforms.
-
Product
PXI/PXIe Microwave Transfer Switch, Single, 18 GHz, 50 Ω, SMA, Failsafe, Remote Mount
42-782B-521-E
Switch Module
The 40-782B-521-E (PXI) and 42-782B-521-E (PXIe) single failsafe transfer switches with remotely mounted relays are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50 Ω and a maximum operating frequency of 18 GHz. Connections are made via front panel mounted high quality SMA coaxial connectors.
-
Product
High Density Switching PXI Card
GX6338
Switch Module
The GX6338 is a low cost 6U switching card with 114 individual low level SPST Form A relays capable of switching 0.5 A at 200 VDC. The GX6338 is ideal for applications requiring high density switching.
-
Product
PXI 23 Channel Low Thermal MUX
40-620-022
Multiplexer Module
Pickering 40-620 Multiplexer modules are similar to other Pickering Multiplexer cards except thermal EMF is substantially reduced to <1.5V with 250nV thermal stability. Typical applications include signal routing in ATE, selecting thermocouple inputs, switching amplifier gain circuits and high accuracy DC microvolt measurements.
-
Product
PXI High Density Multiplexer, 5-Bank, 32-Channel, 1-Pole
40-615A-005
Multiplexer Module
The 40-615A-005 is a 5-bank, 32-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
Product
LXI Microwave Multiplexer, SP4T, 3-Bank, 50GHz, 50Ω, SMA-2.4
60-803-603
Multiplexer Module
Our 60-803-603 is a 3 bank SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-803 range is capable of supporting up to 16 banks of 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
PXI Very High Density MUX 49 Chan 4 Pole
40-675-002-49/4
Multiplexer Module
The 40-675 series of very high density low cost multiplexer modules are available in a versatile range of switching configurations. The modules are supplied pre-configured in one of six multiplexer modes suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
Product
PXI 3A Power MUX BRIC, 8-Channel, 12-Pole
40-571-302
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
Mini Coax, Module, ITA, 90 Series, 19 Position
510108111
ITA Module
Primary mating module 510104120. (May mate with other Receiver modules, as well.)
-
Product
Scienlab Measurement And Control Module
SL1063B
Communications Module
The Measurement & Control Module SL1063B is a rack-mount measuring and control module for measuring and switching of digital signals with 16 digital in-/output channels. The module can be used either as a stand-alone device or as extension for a Scienlab Battery Test System.
