Trigger Modules
-
Product
PXI/PXIe Microwave Multiplexer, Single SP4T, 40GHz, 50Ω, SMA-2.9
40-784B-141
Multiplexer Module
The 40-784B-141 (PXI) and 42-784B-141 (PXIe) are single SP4T 40GHz unterminated microwave multiplexers. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP6T, 67GHz, 50Ω, SMA-1.85
40-785C-571
Multiplexer Module
The 40-785C-571 (PXI) and 42-785C-572 (PXIe) are single SP6T 67GHz unterminated microwave multiplexers. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
16-CH 0-20mA Analog Input EtherCAT Module
EPS-3216
Analog Input Module
ADLINK's EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
Product
PXI 12-Slot BRIC Matrix, 294x12 1-Pole (7 sub-cards)
40-558-121-294X12
Matrix Switch Module
The 40-558-121-294x12 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-142-HI
Programmable Resistor Module
The 40-230-142-HI (PXI) and 42-230-142-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4Ω and 392kΩ with 0.5Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI/PXIe Microwave Multiplexer, Triple SP4T, 40GHz, 50Ω, SMA-2.9
40-784B-143
Multiplexer Module
The 40-784B-143 (PXI) and 42-784B-143 (PXIe) are triple SP4T 40GHz unterminated microwave multiplexers. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
Product
PXI 10W Programmable Resistor Module, 1-Channel, 1.5Ω to 472Ω
40-253-020
Programmable Resistor Modules
The 40-253-020 is a programmable resistor module with 1 channel which can be set between 1.5Ω and 472Ω with 0.125Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-246-HI
Programmable Resistor Module
The 40-230-246-HI (PXI) and 42-230-246-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4Ω and 5.806MΩ with 8Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI Programmable Resistor Module 10x16 Bit, 0 Ohm to 65K Ohm
40-295-121-10/16
Programmable Resistor Modules
The 40-295 is a Programmable Resistor module with up to 18 channels of 8-bit resolution resistor chains in a single 3U PXI module. The flexible architecture allows these modules to also be supplied as 12, 16 or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count.
-
Product
Mini Coax, Module, Receiver, 90 Series, 76 Position
510104150
Receiver Module
Primary mating module 510108132. (May mate with other ITA modules, as well.)
-
Product
PXI High Density Precision Resistor Module, 18-Channel, 2Ω to 62.1Ω
40-298-011
Programmable Resistor Modules
The 40-298-011 is a high density programmable resistor module with 18 channels which can be set between 2Ω and 62.1Ω with 0.25Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI 12-Slot BRIC Matrix, 132x4 2-Pole (3 sub-cards)
40-562B-322-132X4
Matrix Switch Module
The 40-562B-322-132X4 is a high density BRIC12 matrix module with a size of 132x4 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP4T, 67GHz, 50Ω, SMA-1.85, Remote Mount
40-785C-471-E
Multiplexer Module
The 40-785C-471-E (PXI) and 42-785C-471-E (PXIe) are single SP4T 67GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXI Versatile Multiplexer, Solid State, 350mA, 60V
40-681A-001
Multiplexer Module
The 40-681A-001 is a very high-density versatile PXI Multiplexer module featuring a wide range of selectable switching configurations with 350mA current and 60V voltage handling. The 40-681A is especially useful where a high-density MUX array is required that can adapt to different test configurations for different test targets, or where a test system may have to be reconfigured in the future.
-
Product
PXI 4-Slot BRIC Matrix, 2A 1-Pole 116x6, 2 Sub-cards
40-596A-002
Matrix Switch Module
The 40-596A-002 is a PXI 1-pole 116x6 matrix in BRIC4 format and is part of a range of high density matrix modules able to switch up to 2 A or 300VDC/250VAC. The 40-596A BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
NI-9201, ±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
779372-01
Voltage Input Module
±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The NI‑9201 is an effective combination of channel count and speed at a low price for an economical multifunction system. The module features up to 100 V of overvoltage protection for errant signal connection or unexpected signals to the individual channels.
-
Product
PXI Precision Resistor Module 3-Channel, 2.5 to 395k
40-297-142
Programmable Resistor Modules
This 3-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI Dual 6 to 1 RF Multiplexer 6GHz 50 Ohm SMA Terminated
40-881-002
Multiplexer Module
The 40-881 is a 50 Ohm 6 to 1 6GHz multiplexer available as a single or dual MUX in one and two PXI slots respectively. The 40-881 exhibits low VSWR characteristic over the full operating frequency range and consistent insertion loss characteristics. The use of solid state switches ensure a long service life with no wear out mechanism, making the 40-881 ideal for ATE systems requiring frequent and fast operating RF switching with no contact bounce.
-
Product
PXI Potential Divider Module 12-Channel (no resistors fitted)
40-282-021
Programmable Resistor Module
The 40-282 is a potential divider with up 24 separate channels. This can be used to emulate potentiometer devices, each channel having a fixed R1 R2 ratio. Additionally, the centre point can be shorted to either of the potentiometer end points.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 62.5/125 Fiber
40-850A-514-M62.5-HI
Multiplexer Module
The 40/42-850A-514-M62.5-HI is a PXI/PXIe 4-channel multiplexer with ST connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
PXI 12-Slot BRIC Matrix, 176x16 1-Pole (16 sub-cards)
40-562B-321-176X16
Matrix Switch Module
The 40-562B-321-176X16 is a high density BRIC12 matrix module with a size of 176x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 4 Slot BRIC 88x4 1-Pole (2 sub-cards)
40-562A-021-88X4
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI/PXIe MEMS Optical Switch, Single Insert/Bypass
40-860A-112
Multiplexer Module
The 40/42-860A-112 is a PXI/PXIe single insert/bypass switch with FC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP4T, 26.5GHz, 50Ω, SMA, Remote Mount
40-785C-432-E
Multiplexer Module
The 40-785C-432-E (PXI) and 42-785C-432-E (PXIe) are dual SP4T 26.5GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXI/PXIe RF Matrix, 32x8, 150 MHz, 50 Ω, SMB, With Y Loop-thru
42-724-021-L
Matrix Switch Module
The 40-724-021-L (PXI) and 42-724-021-L (PXIe) are 32x8 RF matrix modules with y-axis loop-thru and are suitable for switching frequencies up to 150 MHz. Having a 50 Ω characteristic impedance and front panel SMB connectors, these modules provide a simple and scalable bidirectional matrix for RF and are intended for the easy construction of high performance switching systems.
-
Product
LXI High Voltage Multiplexer Plugin Module
65-231-904-HI
Multiplexer Module
The 65-231-904-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
cRIO-9803, Up to 480 GB SSD Expansion Module for CompactRIO
785920-01
Module
Up to 480 GB SSD Expansion Module for CompactRIO - The cRIO-9803 provides a bus-powered USB SATA bridge to a full-length mSATA solid-state drive (SSD). This module uses a USB Type C connector with integrated cable retention. It also works with devices that feature other types of USB connectors, such as CompactRIO Single-Board Controllers, Industrial Controllers, and PXI Controllers. The cRIO-9803 is available in 64 GB SLC for high endurance in rugged environments, in 480 GB MLC for high-capacity data storage, and for use with a customer-supplied SSD. Additionally, the cRIO-9803 features the same rugged shock and vibration ratings as other CompactRIO modules and can be mechanically connected to a controller for integration using mounting accessories.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP6T, 18GHz, 50Ω, SMA, Terminated
40-785C-521-T
Multiplexer Module
The 40-785C-521-T (PXI) and 42-785C-521-T (PXIe) are single SP6T 18GHz microwave multiplexers with automatic termination of unused signals. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
LXI Microwave Matrix, 10GHz, Dual 4x4
60-750-244-B
Matrix Switch Module
The 60-750-244-B is a dual 4x4 10GHz microwave matrix with internal termination. It is part of the 60-750/751 range of LXI Microwave Switches controlled through an LXI compliant Ethernet connection. It is available in a variety of configurations and frequencies up to 18GHz (60-751). The matrix is characterized for 50 ohm applications, for 75 ohm versions please consult your local sales representative.
-
Product
PXI 8-slot BRIC Matrix, 128x8, 1 pole (2 Sub-cards)
40-558-801-128x8
Matrix Switch Module
The 40-558-801-128x8 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
