Trigger Modules
-
Product
PCI High Density Pecision Resistor Card, 3-Channel, 3.5Ω To 395kΩ
50-298-142
Programmable Resistor Module
The 50-298-142 is a high density programmable resistor card with 3 channels which can be set between 3.5Ω and 395kΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI 8 Slot BRIC 121x16 2-pole (11 sub-cards)
40-562A-122-121X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 8 Slot BRIC 322x8 1-Pole Dual Analog Bus (7 sub-cards)
40-560A-121-322X8-M
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PCI 9-Channel Precision Resistor Card
50-297-101
Precision Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
LXI High Density 40x20 Matrix
60-590-001
Matrix Switch Module
The 60-590 is a high-density single pole LXI matrix available in 40x20 or 40x40 configurations and is suitable for signal routing in large ATE systems.
-
Product
PXI High Density Precision Resistor Module, 9-Channel, 2Ω to 122Ω
40-298-112
Programmable Resistor Module
The 40-298-112 is a high density programmable resistor module with 9 channels which can be set between 2Ω and 122Ω with 0.5Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI 8 Slot BRIC 55x4 2A 2-Pole Matrix
40-566A-101
Matrix Switch Module
These modules are 2 Amp high-density large PXI matrix modules with the ability to switch up to 2 Amps at 150VDC/100VAC. They are available in 4 or 8-slot PXI sizes and are constructed using quality electro-mechanical relays for high switching confidence.
-
Product
2X8 PXIe Switch Matrix, 300 KHz to 9 GHz
M9165B
Matrix Switch Module
M9165B 2X8 PXIe switch matrix, 300 KHz to 9 GHz is a full cross-bar switch matrix that provides a switch based multiport VNA solution.
-
Product
PXI 8-Slot BRIC Matrix, 2A 1-Pole 232x6, 4 Sub-cards
40-596A-104
Matrix Switch Module
The 40-596A-104 is a PXI 1-pole 232x6 matrix in BRIC8 format and is part of a range of high density matrix modules able to switch up to 2 A or 300VDC/250VAC. The 40-596A BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXIe-4300, 16-Bit, 8-Channel, 250 kS/s, 300 V, Ch-Ch Isolated PXI Analog Input Module
781337-01
Analog Input Module
16-Bit, 8-Channel, 250 kS/s, 300 V, Ch-Ch Isolated PXI Analog Input Module—The PXIe‑4300 provides integrated data acquisition and signal conditioning for high-voltage measurements. It provides increased accuracy, simultaneous sampling, and synchronization features for scalable measurement systems. The PXIe‑4300 includes 300 Vrms channel‑to‑channel CAT II isolation and 3,300 Vrms channel‑to‑earth 5 second withstand isolation to protect users and equipment from hazardous voltages. This module offers programmable lowpass filtering, DC input coupling, and two PFI lines for digital input triggering. The included NI‑DAQmx driver simplifies hardware and configuration and measurement.
-
Product
PXI/PXIe Microwave Multiplexer, Triple SP6T, 18GHz, 50Ω, SMA, Remote Mount
40-785C-523-E
Multiplexer Module
The 40-785C-523-E (PXI) and 42-785C-523-E (PXIe) are triple SP6T 18GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PCI High Density Pecision Resistor Card, 3-Channel, 3.5Ω To 201kΩ
50-298-141
Programmable Resistor Module
The 50-298-141 is a high density programmable resistor card with 3 channels which can be set between 3.5Ω and 201kΩ with 0.25Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
LXI High Voltage Switching Multiplexer
65-231-914-HI
Multiplexer Module
The 65-231-914-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
PXI/PXIe High Density Precision Resistor Module, 4-Channel
40-297A-135
Precision Resistor Module
The 40-297A-135 (PXI) and the 42-297A-135 (PXIe) are 4-channel programmable resistors with a range of 2 Ω to 201 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
NI-9208, 500 S/s, ±20 mA, 16-Channel C Series Current Input Module
780968-01
Current Input Module
500 S/s, ±20 mA, 16-Channel C Series Current Input Module - The NI‑9208 is designed with industrial systems in mind. It includes a high-resolution mode with 50/60 Hz rejection to remove low frequency noise. It has high-channel density to reduce the number of modules needed, which leaves slots open for other measurement types or for reducing the overall per channel cost of the system. The NI‑9208 uses a standard D‑SUB connection for use with cables and connector blocks.
-
Product
NI-9215, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
779011-01
Voltage Input Module
±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9215 performs differential analog input. The module contains NIST-traceable calibration, a channel‑to‑earth ground double isolation barrier for safety and noise immunity, and high common-mode voltage range. It is also offered in two connectivity variants: 10‑position screw terminal or BNC.
-
Product
PXI Load Resistor Module 40 Ohm to 295 Ohm
40-292-011
Load Resistor Module
The 40-292 module is able to simulate the common short circuit and open circuit conditions that can be experienced in a system due to faulty wiring or sensors. The short circuit position is fully thermally protected and provides a short circuit current limit. The series open switch provides an automatic current limit through the resistor chain and is thermally protected.
-
Product
PXI 4 Slot BRIC 96x12 2A 1-Pole Matrix
40-597-003
Matrix Switch Module
The 40-597 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 100VDC/70VAC. The 40-597 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI High Density MUX BRIC, 16-Chan, 20-Pole
40-570-312
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
PXI/PXIe 15W Programmable Resistor Module
40-254-113
Programmable Resistor Module
The 40-254-113 (PXI) and 42-254-113 (PXIe) are programmable resistor modules with 1 channel which can be set between 1Ω and 238Ω with 1Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
Dual 4 to 1 Terminated 50 600MHz PXI RF Multiplexer
40-761-002
Multiplexer Module
This terminated dual 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
LXI HD Dual 16x64 2A Matrix With BIRST
60-552-029
Matrix Switch Module
A high-density single pole LXI matrix module capable of switching up to 300VDC/250VAC, 2A (60W max). The use of high-quality electro-mechanical relays offers high switching confidence for signal routing in large ATE systems.
-
Product
NI-9482, 4-Channel, SPST Relay, 60 VDC (1 A)/250 VAC (1.5 A) C Series Relay Output Module
782999-01
Relay Output Module
The NI‑9482 directly connects to a wide array of industrial devices such as motors, actuators, and DC devices. Each channel provides access to an electromechanical relay for switching signals up to 60 VDC (1 A) or 250 Vrms (1.5 A), features channel‑to‑channel isolation, and has a LED that indicates the status. The shock and vibration rating for the NI‑9482 is limited compared with other CompactDAQ and CompactRIO modules because of the mechanical relays on the module.
-
Product
PXI Resistor Module 4-Channel 1R to 127R with SPDT
40-293-112
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI 12-Slot BRIC Matrix, 484x4 2-Pole (11 sub-cards)
40-562B-322-484X4
Matrix Switch Module
The 40-562B-322-484X4 is a high density BRIC12 matrix module with a size of 484x4 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 10x8 Power Matrix 2A 1 Pole
40-547-001
Matrix Switch Module
Model 40-547-001 is a high density single 1-pole 10x8 power matrix module. It is also available in dual 10x4, dual 10x4 or single 20x4 relay formats: Typical applications include power routing in Functional ATE systems, specifically automotive electronics, for example testing of Engine Management Units.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP8T, 26.5 GHz, 50 Ω, SMA, Terminated, Remote Mount, Failsafe
40-788-042-TE
Multiplexer Module
The 40-788-042-TE (PXI) and 42-788-042-TE (PXIe) are dual failsafe SP8T 26.5 GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-788 range of multiplexers are also available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel.
-
Product
PXI 8-slot BRIC Multiplexer, 5-Channel, 160-Pole (7 Sub-cards)
40-570A-015
Multiplexer Module
The 40-570A-015 is a 5-channel, 160-pole High-Density Multiplexer and is part of our BRIC family. The 40-570A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
Product
LXI Microwave Multiplexer, SP6T, 9-Bank, 26.5GHz, 50Ω, SMA
60-800-309
Multiplexer Module
Our 60-800-309 is a 9 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
Matrix Module For SwitchBlock
Matrix Switch Module
The Matrix Module for SwitchBlock is for use with the PXI Carrier Module for SwitchBlock and can operate as an individual relay card, can combine with other Matrix Modules for SwitchBlock in the same PXI Carrier Module for SwitchBlock, and can combine with other Matrix Modules for SwitchBlock in other PXI Carrier Modules for SwitchBlock in the same PXI chassis. Each Matrix Module for SwitchBlock comes in an A-type version, which serves as the first matrix building block and offers row and column access through the front connector, and a B-type version, which serves as an expansion module and only provides column access through the front connector. Typically, SwitchBlock systems contain one A-type module and numerous B-type modules.
