Synchronization Modules
-
product
PXI 4 Slot BRIC 20x32 1-Pole (4 sub-cards)
40-562A-021-20X32
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
LXI High Density 192x8 2-Pole 2A Matrix With BIRST
60-555-023
High density double pole matrix capable of switching up to 300VDC/250VAC, or 2A (60W max). The use of high quality electro-mechanical relays offer high switching confidence and make it suitable for signal routing in large ATE systems.
-
product
PXI/PXIe 15W Programmable Resistor Module
40-254-032
The 40-254-032 (PXI) and 42-254-032 (PXIe) are programmable resistor modules with 1 channel which can be set between 2Ω and 26.7kΩ with 0.5Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
product
Signal, Module, Receiver, QuadraPaddle, 90 Series, 192 Position, Fully Loaded w/ Twin Female Contacts & Square Posts for Wire Wrap (p/n's 610138200 & 610138118)
510150136
Primary mating module 510151105. (May mate with other ITA modules, as well.)
-
product
PXIe System Sync Module, 2 Port
M9032A
The M9032A has a Soft Front Panel (SFP) that provides a graphical user interface to the system sync module. It allows the user to set up the most commonly used functionalities of the module. The SFP also gives you the ability to check the module's connection status, configure the reference clock and IO settings, and perform firmware udpates.
-
product
8/16-CH 16-Bit Analog Output Modules
cPCI-6208/6216 Series
- PICMG 2.0 Rev 2.1- 16-bit D/A resolution- 16-CH voltage on 6216V- 8-CH voltage outputs on 6208A and 6208V- 8-CH current outputs on 6208A- Bipolar analog output range- 4-CH TTL DI and 4-CH TTL DO- Rear I/O available
-
product
PXI 6-Channel 10A Solid State SPST Switch
40-182-011
The 40-182-011 has 6 off high current SPST switches in two PXI slots and is part of our range of high power solid state switching solutions. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.
-
product
PXI 4-Slot BRIC Matrix, 88x4 1-Pole (2 sub-cards)
40-562B-021-88X4
The 40-562B-021-88X4 is a high density BRIC4 matrix module with a size of 88x4 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
PXI 8-slot BRIC Power Multiplexer, 16-Channel, 12-Pole (6 Sub-cards)
40-571A-304
The 40-571A-304 is a 16-channel, 12-pole 3 Amp Power Multiplexer and is part of our BRIC family. The 40-571A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
product
PXI 2.5W Programmable Resistor Module, 2-Channel, 2.5Ω to 773kΩ
40-251-043
The 40-251-043 is a programmable resistor module with 2 channesl which can be set between 2.5Ω and 773kΩ with 1Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PXI 2 Slot BRIC 150x4 2A 1-Pole Matrix
40-568-202
The 40-568 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 200VDC/140VAC. The 40-568 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
product
PXI/PXIe Microwave Multiplexer, Single SP8T, 18 GHz, 50 Ω, SMA, Terminated, Remote Mount, Failsafe
40-788-021-TE
The 40-788-021-TE (PXI) and 42-788-021-TE (PXIe) are single failsafe SP8T 18 GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-788 range of multiplexers are also available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel.
-
product
LXI High Density 96x16 2A Matrix with BIRST
60-554-023
A high-density single pole matrix module capable of switching up to 300VDC/250VAC, 2A (60W max). The use of high-quality electro-mechanical relays offers high switching confidence for signal routing in large ATE systems.
-
product
PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer
781774-01
Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.
-
product
PXI 8-slot BRIC Matrix, 768x8, 1 pole (12 Sub-cards)
40-558-801-768x8
The 40-558-801-768x8 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 32.7k Ohm
40-294-032
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Single 8 to 1 Terminated 50 600MHz PXI RF Multiplexer
40-763-001
This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
product
NI-9265, 4-Channel C Series Current Output Module
783733-01
4-Channel C Series Current Output Module - The NI‑9265 is ideal for interfacing and controlling industrial current-driven actuators at high rates. The module has built-in open-loop detection, which generates an interrupt in software when an open loop is detected as well as zeroing outputs to ensure safety and avoid driving actuators at system power on. The NI‑9265 requires an external power supply and includes a channel‑to‑earth ground double isolation barrier for safety and noise immunity.
-
product
PXI Single 46x4 Matrix, 1 Pole Switching
40-524-021
Medium density PXI dual 46x4, 1-pole matrix - it is also available inreed relay formats of 2-pole and 1-pole screened (see "also in this range" on right). The screened version is suitable for switching signals up to 50MHz. Typical applications include signal routing in ATE and data acquisition systems. The two banks may be used for operating a 4-wire measurement system (bank-1 for source, bank-2 for measure). Larger matrices may be constructed by daisy chaining the common signals from multiple PXI Modules.
-
product
LXI Microwave Multiplexer, 50Ω 4-Channel 8-Bank 6GHz SMA
60-802-008
The 60-802-008 is a 4-channel, 8-bank RF multiplexer suitable for switching 50Ω signals up to 6GHz. It is part of a range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for between 1 and 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
sbRIO-9201, Non-Enclosed, ±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
781114-01
Non-Enclosed, ±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The sbRIO‑9201 is an effective combination of channel count and speed at a low price for an economical multifunction system. In addition to the absolute protection from the isolation, the module features up to 100 V of overvoltage protection for errant signal connection or unexpected outputs to the individual channels. Non-enclosed modules are designed for OEM applications.
-
product
SIMRC - 8 x 2 Matrix 1-Pole Screened Relay
1030-R-8-2-1RF-5/1D
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
product
PXI 4-slot BRIC Matrix, 336x6, 1 Pole (4 Sub-cards)
40-558-401-336x6
The 40-558-401-336x6 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
PXI 8-slot BRIC Matrix, 420x6, 1 Pole (5 Sub-cards)
40-558-801-420x6
The 40-558-801-420x6 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
PCI Resistor Card 2-Channel 1.5 Ohm To 2.04k Ohm With SPDT
50-293-122
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI Potentiometer Module 2x12 Bit, 0 Ohm to 4K Ohm
40-296-021-2/12
The 40-295 is a Programmable Resistor module with up to 18 channels of 8-bit resolution resistor chains in a single 3U PXI module. The flexible architecture allows these modules to also be supplied as 12, 16 or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count.
-
product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 50/125 Fiber
40-852A-218-M50
The 40/42-852A-218-M50 is a PXI/PXIe 8-channel multiplexer with SC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
product
PXI RF Multiplexer, 4x SP4T, 1.3 GHz 75 Ω, SMB Connectors
40-755-304
The 40-755-304 is a 5xSP4T 75 Ω multiplexer and is part of a range of high density RF multiplexers available in 50 Ω and 75 Ω variants with up to 10xSP4T switches in a single PXI module. They are available with two connector options; SMB that provides a frequency range of 1.8 GHz (50 Ω) / 1.3 GHz (75 Ω), or multiway which limits the bandwidth to 1.3 GHz but offers a high density solution occupying one PXI slot.
-
product
PXI 5W Programmable Resistor Module, 2-Channel, 1.5Ω to 925Ω
40-252-021
The 40-252-021 is a programmable resistor module with 2 channesl which can be set between 1.5Ω and 925Ω with 0.25Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-155
The 40-297A-155 (PXI) and the 42-297A-155 (PXIe) are 3-channel programmable resistors with a range of 3 Ω to 43.8 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
