Synchronization Modules
-
product
PXI High Density MUX BRIC, 32-Chan, 10-Pole
40-570-412
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
product
PXI 8-slot BRIC Power Multiplexer, 24-Channel, 6-Pole (5 Sub-cards)
40-571A-403
The 40-571A-403 is a 24-channel, 6-pole 3 Amp Power Multiplexer and is part of our BRIC family. The 40-571A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 63.7 Ohm - SPST
40-294-111
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI 8-Slot High Density 2A BRIC Matrix, 232x8 2-Pole (8 Sub-cards)
40-573-102-232X8
The 40-573-102-232x8 BRIC is part of a range of high density matrix modules able to switch up to 2 A at 240 VDC/250 VAC. They are available in 2, 4 or 8-slot sizes to suit most high performance matrix requirements, constructed using quality electromechanical relays for high switching confidence.
-
product
LXI Microwave Multiplexer, 50Ω 6-Channel 8-Bank 6GHz SMA
60-801-008
The 60-801-008 is a 6-channel, 8-bank RF multiplexer suitable for switching 50Ω signals up to 6GHz. It is part of a range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for between 1 and 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
PXI 2.5W Programmable Resistor Module, 2-Channel, 1.5Ω to 1.81kΩ
40-251-122
The 40-251-122 is a programmable resistor module with 2 channels which can be set between 1.5Ω and 1.81kΩ with 0.5Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PXI Solid State MUX, 10 bank, 16 channel
40-680-002
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
product
PXI 2A Multiplexer, 4-Bank, 32-Channel, 1-Pole
40-614C-006
This 4-bank, 32-channel, 1 pole version is part of the 40-614C High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
PXI 8 Slot BRIC 270x8 1-Pole (9 sub-cards)
40-561A-121-270X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI 4-Slot BRIC 96x8 Matrix, 2A 2-Pole (4 sub cards)
40-565A-002-96X8
The 40-565A PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps at 150VDC/100VAC The 40-565A BRIC modules are available in 2, 4 or 8 slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using quality electro-mechanical relays for high switching confidence.
-
product
PXI/PXIe RF Matrix, 16x8, 300 MHz, 50 Ω, SMB
40-724-011
The 40-724-011 (PXI) and 42-724-011 (PXIe) are 16x8 RF matrix modules suitable for switching frequencies up to 300MHz. Having a 50 Ω characteristic impedance and front panel SMB connectors, these modules provide a simple and scalable bidirectional matrix for RF and are intended for the easy construction of high performance switching systems.
-
product
PXI Precision Resistor Module 3-Channel, 3 to 11.4M
40-297-153
This PXI Precision Resistor module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PXI/PXIe High Density Precision Resistor Module, 4-Channel
40-297A-120
The 40-297A-120 (PXI) and the 42-297A-120 (PXIe) are 4-channel programmable resistors with a range of 1.5 Ω to 472 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI 2A Multiplexer, 4-Bank, 32-Channel 1-Pole
40-614-006
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
product
PXI 8-Slot BRIC Matrix, 132x8 1-Pole (6 sub-cards)
40-562B-121-132X8
The 40-562B-121-132X8 is a high density BRIC8 matrix module with a size of 132x8 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
Switched Power Distributed Module, CAN Control
H730008xS
The intelligent Power Distribution Unit (PDU) H7300.08xx has two main functions: Distributing the power to each device in a system Switching on the devices sequentially, in order to minimize the inrush current from the switched power supplies, that might affect the contactors.
-
product
PXI Dual 12x8 Matrix, 1 Pole Switching
40-522-021
Medium density PXI dual 12x8, 1-pole matrix - it is also available inreed relayformats of 2-pole and 1-pole screened (see "also in this range" on right). The screened version is suitable forswitching signals up to 50MHz. Typical applications include signal routing in ATE and data acquisition systems.The two banks may be used for operating a 4-wire measurement system (bank-1 for source,bank-2 for measure). Larger matrices may be constructed by daisy chaining the commonsignals from multiple PXI Modules.
-
product
LXI Single 32 Channel Fiber Multiplexer SC, Single-Mode With Loop-Thru
60-850-224
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
product
PXI/PXIe Microwave Multiplexer, Dual SP6T, 18 GHz, 50 Ω, SMA, Failsafe
42-784B-022
The 40-784B-022 (PXI) and 42-784B-022 (PXIe) are dual SP6T failsafe 18 GHz unterminated microwave multiplexers. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
product
PXI Single SP4T Multiplexer 18GHz 50 SMA
40-784A-121
Pickering Interfaces’ range of 40-784A PXI Microwave Multiplexer Modules have a characteristic impedance of 50Ω and are capable of switching signals up to 40GHz. Available in single, dual or triple, SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors
-
product
PXI High Density Multiplexer, 94-Channel, 1-Pole
40-640A-022-94/1
The 40-640A-022-94/1 is a 94-channel, 1-pole MUX and is part of a series of high density multiplexer modules featuring a choice of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
product
PXI 12-Slot BRIC Matrix, 210x12 1-Pole (5 sub-cards)
40-558-121-210X12
The 40-558-121-210x12 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
PXI/PXIe Microwave Multiplexer, Single SP10T, 22 GHz, 50 Ω, SMA, Failsafe
40-788-131
The 40-788-131 (PXI) and 42-788-131 (PXIe) are single failsafe SP10T 22 GHz unterminated microwave multiplexers. The 40/42-788 range of multiplexers are available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel. Remote versions are also available which can support one or two multiplexers in a dual slot module.
-
product
PXI 2 Slot BRIC 48x16 2A 1-Pole Matrix
40-598-202
The 40-598 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 100VDC/70VAC. The 40-598 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
product
12-Slot BRIC PXI Matrix, 576x16 1-Pole (18 sub-cards)
40-558-121-576X16
The 40-558-121-576x16 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
sbRIO-9860, Non-Enclosed, 2-Port, C Series Vehicle Multiprotocol Interface Module
787325-01
Non-Enclosed, 2-Port, C Series Vehicle Multiprotocol Interface Module - The sbRIO-9860 is a hardware-selectable HS/FD controller area network (CAN) and/or local interconnect network (LIN) interface for developing CAN and/or LIN applications. As part of the NI-XNET product line, the sbRIO-9860 works well for applications requiring high-speed manipulation of hundreds of frames and signals while performing low-level FPGA control and embedded monitoring in the same CompactRIO Single‐Board Controller. Non-enclosed modules are available for OEM applications.
-
product
PXI/PXIe Wide Current Range Multiplexer Module, Single 12-Channel, 2-Pole
42-514-105
The 40-514-105 (PXI) and 42-514-105 (PXIe) are low density multiplexers in single 12-channel, 2-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
-
product
PXI Solid-State Switch Module, 3xSPST, 1.5 A, 400 V
40-185A-002
The 40-185A-002 has 3-off high current SPST switches in one PXI slot and is part of our range of high power solid state switching solutions.. Each SPST switch uses a fully isolated solid-state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.
-
product
PXI/PXIe Microwave Multiplexer, Single SP6T, 40 GHz, 50 Ω, SMA-2.9, Remote Mount, Failsafe
42-784B-041-E
The 40-784B-041-E (PXI) and 42-784B-041-E (PXIe) are single failsafe SP6T 40 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
product
PXI BRIC8 FIBO Matrix Dual 120x4 3pin brkout
40-592A-106
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
