Simulators
create what could be.
See Also: Simulation, Simulation Software, Simulation Testing, Emulators
-
Product
Ethernet Test and Simulation Instruments for Speeds from 10 Mbit/s to 25 Gbit/s
-
Avionics Interface Technologies
AIT’s Ethernet test instruments provide Ethernet test features for 10Mbit, 100Mbit, 1Gbit, and 10Gbit Ethernet networks, for both Optical and Copper media. All instruments are supported by Analyzer and Simulator software applications (GUIs) and additionally software API’s allowing integration into user applications.
-
Product
ARINC 429 Test & Simulation Interface for VME
VME-429
-
Avionics Interface Technologies
4, 8, 16, 32, or 64 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full Error Injection & Detection - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B Time Code Encoder/Decoder for Data Correlation - ANSI Application interface supporting C, C++, C#, and .net development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME - Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
Product
Simulation Transport Vibration Table
CX-M120
-
Shenzhen Chuangxin Instruments Co., Ltd.
CX-M120 Simulation Transport Vibration Table was applicable to toys,furniture,gifts,cera-mics,packaging and other products to simulate the transport tests.Comply with the U.S. and European transport standards and have characteristic with low noise,reasonable structure,durable,etc.Basic Standard:Following The EN.ANSI.UL.ASTM.ISTA International Trans-port Standard.
-
Product
Dynanometer Roller Set
FPS 2700 | VP 230048
-
Maschinenbau Haldenwang GmbH & Co. KG.
The FPS 2700 roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. As a result of the increased tractive force of its eddy current brake, the FPS 2700 is additionally suitable for power measurements at constant speed and constant tractive force.
-
Product
3-Phase AC Power Source
61700 series
-
The Chroma Programmable AC Power Source model 61700 series delivers pure, 5-wire, 3-phase AC power. Unlike the traditional 3-phase AC power source, it includes low power rating models at very low cost. Users can program voltage and frequency, measure the critical characteristics of the output on its LCD display. It delivers the right solution to simulate all kinds of input condition of UUT to be utilized in R&D and QA. It is also suitable for commercial applications from laboratory testing to mass productions. The 61700 supplies the output voltage from 0 to 300VAC and it can be set individually for each phase. Users also can set the phase angle from 0? to 360?. These kinds of function make the 61700 series can simulate unbalance 3-phase power. Because of the wide output frequency from 15 to 1200Hz, it is suitable for avionics, marine and military application. The AC+DC mode extends the output function to simulate abnormal situation when power line contains DC offset.
-
Product
Vector Network Analyzer (VNA) Simulator – Standard
S94050B
-
S94050B puts flexible S-parameter analysis into your own computer. Dive deeper into measurements captured on a network analyzer or develop and optimize test programs before deploying them onto an instrument.
-
Product
AFDX ® / ARINC 664 Test Cards
-
Our AFDX ® / ARINC664 test cards can be used for test and simulation applications in which it is necessary to send and receive data via the AFDX® data bus. They support the 10/100 Mbit / s ARINC 664 Part 7 Ethernet interface as well as the next generation 1 Gbit / s Ethernet. / ARINC 664 test cards are delivered with device drivers, high-level interfaces (APIs) for Windows Linux, VXWorks and LabVIEW / LabVIEW Real-Time (further on request).
-
Product
PXI Strain Gauge Simulator Module 6-Channel, 2k
40-265-306
-
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 2kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
The Leading Measurement System for the Analysis of Porous Materials
ELWIS
-
ELWIS (Evaluation of Light Weight Impedance System) offers a full and rapid characterization of porous materials based on the analysis of a single sample. The ELWIS system consists of the ELWIS-A and ELWIS-S components which can be used independently from each other although both applications are needed for a complete material simulation.ELWIS-A measures acoustic parameters that are needed to evaluate the acoustic performance of sound insulation and sound-absorbing multi-layer materials. An additional impedance tube for absorption measurements at higher frequencies is available for ELWIS-A.ELWIS-S measures structural parameters that are needed to simulate the dynamic and acoustic behavior of sound packages in the medium to low frequency range (including the "Poisson Ratio" for foam materials).ELWIS is very easy to operate: Thanks to its user-friendly software, the system can also be used to obtain reliable results by users with only limited experience in the characterization of porous materials.
-
Product
Configurable Simulation Of ECU Diagnostics.
TestCUBE2
-
Softing Automotive Electronics GmbH
The ECU simulation TestCUBE2 is the counterpart for all cases of application in which an ECU is not yet (e.g. preparation of workshop tests) or no longer (e.g. tester regression test) available. TestCUBE2 is a configurable hardware and software solution for simulating ECU diagnostics with real bus communication. With just one device, you can simulate several ECUs or even an entire vehicle at the same time.
-
Product
Thermal Test Vehicles
TTV
-
Thermal Engineering Associates, Inc.
Using the TTC-1002 Thermal Test Chip as a basis, TEA offers TTVs in flip-chip, bare die, BGA packages for a variety of thermal simulation, reliability, qualification, heat sink characterization, and TIM characterization activities. Selective unused balls are sequentially connected together for daisy-chain applications.
-
Product
PXI/PXIe High Density Precision Resistor Module, 4-Channel
40-297A-122
-
The 40-297A-122 (PXI) and the 42-297A-122 (PXIe) are 4-channel programmable resistors with a range of 1.5 Ω to 1.81 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXI High Density Precision Resistor Module, 9-Channel, 2.5Ω to 3.55kΩ
40-298-023
-
The 40-298-023 is a high density programmable resistor module with 9 channels which can be set between 2.5Ω and 3.55kΩ with 1Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
High Speed Optical Avionics Network Test Instrument
PXIe-25G
-
Avionics Interface Technologies
PXI Express Instrument for test and simulation of Fibre Channel and Avionics Ethernet (10G and 25G). Instrument provides 4 optical network interfaces and is software configurable to provide 4 ports of Ethernet, 4 ports of Fibre Channel, or 2 ports of each.
-
Product
PEM Fuel Cell Test Stations
-
Available with Greenlight''s integrated ''Intelligent Fuel Cell Diagnostics'' capabilities:FCDXTMCE certification including optional 3rd party verificationIndustry-leading software and diagnosticsAutomated reformate gas simulation (blending)5 different gas humidification technologies available, including Greenlight''s optional Rapid Response humidification system24/7 unattended operation with Emerald control and automation softwareIndustry leading cell voltage monitoring accuracyUser-adjustable safety featuresFuel cell stack leak testingOptional integrated environmental chambersOptional high temperature configuration, specifically designed for PBI membrane researchOptional DMFC configurationWorldwide service and support
-
Product
Panel-mounted Voltage Power Amplifier
PAV120Bi
-
PAV120Bi is specially designed for R&D of power system simulation. It is adapt to various capacitive and inductive load. It is with 6 channels voltage outputs, each channel with 120V/60VA maximum output.
-
Product
Solar Stimulator
XHS Series
-
They are mainly used for the evaluation of solar cells as well as for other types of tests where sunlight needs to be recreated.The continuous light of xenon lamp, the most faithful reproduction of sunlight, is applied in our highly accurate solar simulator, which has been widely sold across Japan and neighboring countries.
-
Product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 16.3k Ohm - SPST
40-294-131
-
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Autonomous Vehicle Simulation
-
Ansys Autonomous Vehicle Simulation provides a solution designed specifically to support developing, testing and validating safe automated driving technologies. This autonomous vehicle simulation solution saves significant time and costs versus traditional development and testing methods by allowing you to exercise your AV/ADAS software stack in a closed loop, with sensor-accurate synthetic data in software-in-the-loop or hardware-in-the-loop context with the driving simulator of your choice.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, 1 kV Isolation
43-752A-103
-
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PXI High Density Precision Resistor Module, 3-Channel, 4Ω to 22.3MΩ
40-298-154
-
The 40-298-154 is a high density programmable resistor module with 3 channels which can be set between 4Ω and 22.3MΩ with 2Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Automated Shock Test Systems
AutoShock-II Test System
-
The AutoShock-II is a fully automated series of shock test systems used to measure and identify product fragility levels and evaluate protective packaging. With the simulation of real world shock pulses and impact energy levels, manufacturers can systematically test and optimize product design and packaging. L.A.B. Equipment, Inc.''s fully automated computer controlled shock and data analysis test systems are the critical path in accomplishing this optimization.
-
Product
Light Simulator
-
From the review of the scientific development history, reliable and stable artificial light sources have played a very important role in the past century. For example, the artificial solar simulator is an important part of simulating sunlight to ensure accurate performance of PV characterization. With the growth of light sensor applications, more and more requirement of light simulators (or artificial light sources) explored. One of the core technologies of Enlitech is the artificial light sources. We can manipulate different lamp types (short arc lamps, LEDs, filament lamps et. al.) to generate different spectrum-form in different light intensity levels, beam sizes, and wavelength ranges. We have launched different artificial light source products for different applications fields. For instance, SS-X series solar simulators and ILS-30 ambient light simulator are for the PV field, HAAS is highly accurate star light simulator for the space field, and ALS-300 is a general-purpose light source in science research field. These products can not only meet the needs of your application, but also speed up the process of your research or mass-production.
-
Product
PCI Strain Gauge Simulator Card, 4-Channel, 3k
50-265-104
-
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
Specialty Lab Testing Services
-
Serving the Testing and Consulting needs for the Aerospace, Automotive, Bio-Medical, Military, Electrical and Electronics Product Industries since 1995 with technical excellence and exemplary customer service. Failure Analysis, Electronics Qualification, Screening, Environmental Test, Shock, Vibration, Package Test, and Transportation Simulation. Our customers come from a diverse group of manufacturers, from start-ups to Fortune 500 companies.
-
Product
Steady State Solar Simulator
-
Our steady state solar simulators enable you to test and develop solar thermal collectors independent of weather and season, faster, more efficiently and more comprehensively than ever before. Both simulators are turnkey products, delivered 100 % ready to go!
-
Product
Precise Testing & Simulation of A2B® Networks
A2B®-Component-Tester
-
The Automotive Audio Bus (A²B®) is a bus developed by Analog Devices Inc. for infotainment systems in automobiles. It is increasingly being used in other applications such as AV conferencing systems. Typical A²B® -products are Hi-Fi amplifiers/speakers, head units, eCall systems, microphones, vibration/noise suppression units, actuators, or sensorsCommunication happens via a simple two-wire UTP (Unshielded Twist Pair) cable. All A²B® -components are connected in a master/slave architecture to form a network. The complexity of audio systems in these A²B® -networks is reduced, and with it the cost and weight.
-
Product
PCIe-7841, Virtex-5 LX30 FPGA, 200 kS/s Multifunction Reconfigurable I/O Device
781100-01
-
Virtex-5 LX30 FPGA, 200 kS/s Multifunction Reconfigurable I/O Device - The PCIe‑7841 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe‑7841 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
Product
Sweating Thermal Guarded Hotplate
-
Sataton Instruments Technology CO., Ltd
Sweating guarded hotplate is the textile testing instrument for measuring of thermal and water-vapour resistance properties under steady-state conditions. By testing the thermal resistance and water-vapour resistance of textile materials, the tester provides a direct data for characterizing the textiles’ physiological comfort which involve a complex combination of heat and mass transfer. The hotplate is intended to simulate the heat and mass transfer processes which occur next to human skin and measure the hence transport properties in a steady-state conditions involving combinations of temperature relative humidity, air speed, and in liquid or gaseous phase.
-
Product
PCI High Density Resistor Card 10-Channel, 12-Bit, 0 To 4k Ohm
50-295A-121-10/12
-
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
