Voltage Current Sources
See Also: Current Sources, Voltage Sources
-
Product
FaithTech Ultra Low Voltage And High Current DC Load
NZ/N Series
-
Shenzhen FaithTech Technology Co., Ltd.
Ultra low voltage and high current DC electronic load is a high reliability and high performance electronic load product derived from FT conventional electronic load for low voltage and high current test scenarios such as fuel cell test and CPU power supply device test. For different current levels, this product includes two series: NZ and N. The voltage is 0-20V or 40V, in which the NZ series can be loaded with 0V full current, and the N series can be loaded with ultra-low voltage and full current. The load capacity is up to 0V@1200A and 0.2V@5000A . This series of products has high precision and high cost performance, which is your good choice for testing.
-
Product
Voltage Calibrators
-
Practical Instrument Electronics, Inc.
PIE has a voltage calibrator to fit your needs from the PIE 235 voltage and pH simulator to the advanced troubleshooting capabilities of the PIE 532 milliamp and voltage calibrator. The PIE 532 includes our patented Loop Diagnostic Technology! All the voltage/milliamp calibrators have fuse-less protection, rugged design and long battery life. With the PIE 535, source 4 to 20 milliamps or 10 to 50 milliamps into loop instruments and drive final control elements such as valves and actuators with up to 42 volts.
-
Product
LED Light Sources
-
LED light sources provide high power at a precise wavelength. A typical application for AvaLight-LED sources is fluorescence. They provide a long lifetime, short warm-up time, and high stability.
-
Product
High Voltage
-
Accurate measurement of high voltages acc. to VDE 0432 und IEC 60060 in conjunction with a high voltage divider.For the measurement, the principle of capacitive or resistive divider is used, which can be selected in the peak voltage meter.
-
Product
Voltage Transformer
-
Beijing GFUVE Electronics Co.,Ltd.
Are a parallel-connected type of instrument transformer. They are designed to present a negligible load to the supply being measured and have an accurate voltage ratio and phase relationship to enable accurate secondary connected metering.
-
Product
Current Sense Magnetics
-
Current sense magnetics are used as a low loss method for sensing AC current in a circuit and also provide electrical and safety isolation between the source of the current and the measurement circuit. The key parameters for a current sense transformer are the rms current rating (to ensure it does not overheat in the application) and the safety and voltage isolation (to ensure it conforms to the end-application requirements).
-
Product
High Current Conditioners
-
IsoTek’s unique Direct Coupled Design system offers extremely low impedance high current clean power for the hardest of loads.
-
Product
Calibration Light Source
CAL2
-
Image Engineering GmbH & Co. KG
The CAL2, based on our 22 channel spectrally tunable iQ-LED source, can be adapted for use in many different areas.
-
Product
Source Systems AC
-
The power sources of MTS-series based on digital amplifier modules combined with frequency generator and reference device are the MTS source system. Single-phase systems (MTS1xx) or three-phase systems (MTS3xx) from 1 to more than 40 test positions are available.
-
Product
Light Sources
-
For applications such as transmission, absorption, and reflection, illumination sources are needed. Avantes offers a wide range of different types of light sources, to suit your specific application needs. An overview of the different types of light sources can be found below.
-
Product
AC Power Source
-
NF’s AC power sources are designed and built to deliver high-quality, high–precision AC power. In recent years, NF’s products have been used for power-supply environment testing such as immunity testing of electronic components.
-
Product
Eddy Current Dynamometers
WT Dyno
-
Our WT series eddy current dynamometers are mainly used in the development and testing of all types of prime mover, as well as various engine assemblies. Due to their robust design, which incorporates improved control characteristics, they can be used both as steady state and as transient test stands.Their high speeds for automobile engine testing and their optimised cooling chamber, are convincing arguments that speak for themselves. All WT type dynamometers are suitable for operation in both directions of rotation.
-
Product
Low Current Probe/DMM
687
-
With the capability of measuring down to 1 milliamp (.001A), the #687 is a great tool for all low current applications. Especially for diagnosing parasitic drains! Clamp opening is large enough to fit over most negative battery cables. Applications: fuel injectors, fuel pumps, electric motors, battery drains, charging systems.
-
Product
Uniform Light Sources
-
It includes universal mounting points and wireless light controls. It is offered with a variety of color temperatures as well as near-infrared.
-
-
Product
Light Source
FiberPal OT-3000
-
The OT-3220/3221 is designed for a high performance stabilized laser source, especially in practice for FTTX networking installation and maintenance fieldworks environment requirements. It is usually applied as stable laser sources for wide range of optical testers and tools in optical fiber cabling and transmission systems.
-
Product
Optical Light Source
STC-OLS201 series
-
Shanghai Stone Communication tech Co., Ltd
a simple and cost-effective fiber optic tester,it is usually used together with fiber optic power meter to measure the optical loss on fiber cables. STC-OLS201 series light source provide multiple wavelength output, the wavelengths can be required on customer specific requirements (the Max wavelength is 5, such as 850/1300/1310/1490/1550nm).
-
Product
Current clamps
-
Precision ammeters determine the intensity of an electric circuit without interrupting the current flow.
-
Product
Current Probe For Oscilloscopes
CP 1005
-
The CP 1005 current probe has been designed for use with oscilloscopes respectively for accurate, non-intrusive measurement of AC, DC and complex waveform currents.
-
Product
Multifunction Voltage and Current Calibrator
MC140i
-
Multifunction calibrator MC140i is ideal for calibration of voltmeters, ammeters, DMMs and panel meters. AC/DC voltage 1uV to 1000V. Current 50uA? to 1000A using test coil. Deviation control along readout. 0.0035% basic dc accuracy. 0.03% basic ac accuracy. Supplied with RS232 interfaces. UKAS/NIST Traceable
-
Product
Clamp type DC/AC Current Sensor／with Voltage Output
LAD-250
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*With DC voltage output*AC/DC 1A～1000A
-
Product
Voltage Amplifiers
-
Switchable gain up to 100 dB (x 100,000)Bandwidth DC to 100 kHzDC-drift 0.6 µV/°CInput noise down to 0.4 nV/√HzSwitchable AC/DC-couplingLocal and remote controlInput impedance up to 1 TΩ
-
Product
Power Sources
MS-Series
-
The MS-Series Power Sources are high performance, high efficiency, AC to AC converters. Rugged powerful output provides up to 350 amps of pulse current for driving non-linear loads.
-
Product
Current Transformer Tester
CT-T1
-
The CT-T1 is a microprocessor-based Current Transformer Tester that measures CT excitation current, turns ratio, and winding polarity tests, all without having to switch the leads during testing. The instrument has a fully automatic knee point detection (ASA 10/50, IEEE 30°, IEEE 45°). Although includes 5 low side taps and 1 high side tap.
-
Product
Remote Plasma Sources
-
Equip your manufacturing and abatement processes with high functionality and exceptional reliability. Customize your chemistry. Expand your operating range. Deliver higher process rates. Advanced Energy’s remote plasma sources offer sophisticated options in streamlined designs.
-
Product
Current Protection Relay
-
The main earth fault protection relays in distributions systems, power stations & large manufacturing / processing plants can fail to detect a high impedance break down to earth causing hazard to human life & potential damage to plant & equipment. In these & other situations demanding extra sensitive earth fault protection, using solid state techniques, can be applied to detect earth currents down to 0.5% of the CT nominal current.
-
Product
Voltage Detectors
-
Non-contact voltage detectors can quickly detect live AC voltage. These handy devices are great for electricians to safety and quickly check the status of electrical wires.
-
Product
Integrated Current Sensors
-
Current sensors have to be smaller, smarter, cheaper. LEM’s R&D is actively developing a range of ICS to reduce the footprint of the current sensing function and simplify the integration of current measurement in a wide range of applications in automotive, industrial, or residential.
-
Product
AC Power Source
-
AC power source 61500 series sets up the new standard for high performance AC power source. It equips with all powerful features such as power line disturbance (PLD) simulation, programmable output impedance, comprehensive measurement functions, wave-shape synthesis and regulation test software.
-
Product
Current Amplifiers
-
In order to achieve an extremely low noise performance very high gains were chosen, while nevertheless minimizing the associated bandwidth reduction.Thus, as a result of our sophisticated development efforts we can offer a professional "High-End" Current Amplifier line. The noise performance of our products surpasses by far that of conventionally designed OpAmp current-to-voltage converters at the corresponding bandwidth.
