Memory Device
directly accessible computer's internal or main memory.
See Also: Memory, Memory Test, DDR, NAND, DRAM, RAM, ROM, Memory Testers, DUT
-
Product
PCIe-6363, PCI Express, 32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO Multifunction I/O Device
781051-01
-
PCI Express, 32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO Multifunction I/O Device - The PCIe‑6363 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PCIe‑6363 is well-suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Measuring Devices For Drawing Rings And Punches For 2-part Can Production
RINGMASTER - The Benchmark For Accuracy
-
Optik Elektronik Gerätetechnik GmbH
High-precision, non-contact measurement of inside and outside diameter, roundness (inside and outside) and concentricity of drawing rings for 2-piece can production. The Ringmaster sets standards in measuring accuracy, user friendliness and reliability and is therefore used in can factories on all continents.
-
Product
USB-6509, 96-Channel, 5 V, TTL/CMOS, 24 mA, USB Digital I/O Device
779975-01
-
The USB-6509 is an industrial, bus-powered USB device that can directly drive external digital devices such as solid-state relays (SSRs). You can configure each port for input or output, and no external power supply is … required for outputs. Using programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators. If a computer or application fault occurs, the USB-6509 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
Testing And Inspection Devices
-
HEIDENHAIN offers testing and inspection devices that deliver all setup, monitoring, and diagnostic data needed for the analysis of its encoders. Grid encoders from HEIDENHAIN are ideal for machine tool inspection and acceptance testing, accurately measuring CNC machine tool movements in both static and dynamic inspection.
-
Product
GPIB-RS485, GPIB Instrument Control Device
779733-04
-
Serial, RS485/RS422 GPIB Instrument Control Device - The GPIB‑RS485 is an IEEE 488 controller device for PCs with RS485 or RS422 ports. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS485 or RS422 … serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS485 and RS422 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488, RS485, and RS422 standards, as well as interpret and execute high-level commands from the serial port, including serial‑to‑GPIB, and GPIB‑to‑serial protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
PCI-5122, 100 MHz Bandwidth, 100 MS/s, 14-Bit PCI Oscilloscope Device
778758-03
-
100 MHz Bandwidth, 100 MS/s, 14-Bit PCI Oscilloscope Device—The PCI‑5122 high-resolution oscilloscope device has two channels with greater than 75 dBc spurious‑free dynamic range (SFDR) and flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for both time-domain and frequency-domain applications that require high-resolution, low-noise measurements with up to 100 MS/s and 100 MHz of analog bandwidth.
-
Product
Inspects MEMS and Wafer Level Devices
NorCom 2020-WL
-
The NorCom 2020-WL is specifically designed for wafer-level inspection and leak tests up to 1000 devices per cycle. The system can inspect up to an 8” wafer on or off a saw frame. It is designed to test MEMS and other wafer level devices that have a cavity.
-
Product
High-Voltage Test Device
PGK 70 HB
-
Cable testing and diagnostics with the BAUR PGK HB. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit.* Testing of medium- and high-voltage cables* DC voltage testing of up to 70 kV output voltage with positive or negative polarity* AC voltage testing - up to 55 kV for switchgear, busbars and insulating elements* Easy-to-maintain 2-piece design
-
Product
Portable Gas Measurement Devices
-
Teledyne Gas & Flame Detection
Looking for portable gas leak detectors to protect your staff? Teledyne Gas and Flame Detection measuring devices meet all your requirements.
-
Product
GPIB-USB-HS, USB, IEEE 488 GPIB Instrument Control Device
778927-01
-
USB, IEEE 488 GPIB Instrument Control Device - The GPIB‑USB‑HS is an IEEE 488 controller device for computers with USB slots. The GPIB‑USB‑HS achieves maximum IEEE 488.2 performance. With no GPIB cable required for instrument connection, you can use the Hi‑Speed USB port to control up to 14 programmable GPIB instruments. This device is completely IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
DC Safety Inspection Device For Solar Panels
“DC Fault Tester”
-
Identifies defect position instantly- contributes to saving inspection time
-
Product
Medical Device Testing
-
Our experts are qualified to assist you in EMC testing a variety of medical devices, from highly advanced robotic surgical systems, basic over-the-counter devices, and everything in between. Backed by more than 30 years of experience, F2 Labs can provide you with the necessary medical device testing and certification to get your product in the hands of doctors and patients on a timely schedule.
-
Product
PXI/PXIe High-Speed Multi-Measurement Device
PXM(e)7820
-
The PXM Multi-Measurement Devices combine the functionalities of a digitizer, a multimeter, a timer/counter and a highly flexible trigger matrix in a PXI or PXIe device.
-
Product
PCIe-5763, 16-Bit, 500 MS/s, 4-Channel PCI FlexRIO Digitizer Device
786165-01
-
The PCIe-5763 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PCIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PCIe-5763 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
Qseven V1.2 SoM Evaluation Kit With I.MX287 454 MHz (Industrial) SoC, 128MB Memory, 4GB EMMC, Gigabit Ethernet, Audio, CAN And BSP
Q7M100-100-EVK
-
*Ultra low power consumption ARM9*High flexibility Qseven v1.2 compliant design*5 UART*2 CAN*24-bit TTL LCD*10/100 Mbps Ethernet*Linux 2.6.35
-
Product
IV Characteristics Measurement Device Software
Keithley 2400, 2401 and Keithley 2450
-
*Windows 10, Windows 11 (Compatible) RS-232C (Keithley 2400, 2401), USB (Keithley 2450)*NI GPIB can also be used (optional)*IPCE PEC-S02 can be used simultaneously. operation panel. *Everything from condition setting to measurement can be done on one screen.
-
Product
PCI-6221, 16 AI (16-Bit, 250 kS/s), 2 AO, 24 DIO PCI Multifunction I/O Device
779066-01
-
The PCI-6221 offers analog I/O, correlated digital I/O, two 32-bit counters/timers, and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PCIe-5763, 16-Bit, 500 MS/s, 4-Channel PCI FlexRIO Digitizer Device
786167-01
-
The PCIe-5763 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PCIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
Product
PCI-6519, 32-Channel, ±30 V, 16 Sink/Source Inputs, 16 Sink Outputs, Bank-Isolated Digital I/O Device
779085-01
-
The PCI-6519 is an industrial digital I/O interface, with two banks optically isolated channels. The device is ideal for industrial control and manufacturing test applications. The PCI-6519 module is an industrial digital I/O interface, with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6519 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions.
-
Product
USRP Software Defined Radio Stand-Alone Device
-
The USRP Software Defined Radio Stand-Alone Device consists of an onboard processor, FPGA, and RF front end. You can program this device using either LabVIEW Communications System Design Suite or an open-source software workflow, depending on the operating system you choose. You can provision the device with NI Linux Real-Time, Linux Fedora, or Linux Ubuntu real-time operating systems. The USRP Software Defined Radio Stand-Alone Device enables you to prototype a range of advanced research applications such as stand-alone LTE or 802.11 device emulation; Medium Access Control (MAC) algorithm development; multiple input, multiple output (MIMO); heterogeneous networks; LTE relaying; RF compressive sampling; spectrum sensing; cognitive radio; beamforming; and direction finding.The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
USRP-2955, 10 MHz to 6 GHz, 80 MHz Bandwidth, GPS-Disciplined OCXO, Reconfigurable USRP Software Defined Radio Device
785264-01
-
The USRP-2955 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless receiver systems. It is designed for over-the-air signal acquisition and analysis. It features a two-stage superheterodyne architecture with four independent receiver channels and shares local oscillators for phase-coherent operation. It also offers a Kintex-7 FPGA programmable with the LabVIEW FPGA Module. With these features, the USRP-2955 has the RF and processing performance for applications such as spectrum monitoring, direction finding, signals intelligence, wideband recording, and radar prototyping. The USRP-2955 is equipped with a GPS-disciplined 10 MHz oven-controlled crystal oscillator (OCXO) Reference Clock, which improves frequency accuracy and synchronization.
-
Product
Laser Distance Meter for 60m With 10 Memories and Min. Measurement
MS-LDM360
-
*Measuring distance: 0.05 to 60m*Accuracy: ±1.5mm (±0.06in)*Unit conversion: mm/in/ft*Laser classification: Class 2*Laser type: 635nm <1mW*Dynamic measurement*Area, volume measurement*Pythagorean proposition measurement*Indirect measurement*Add - subtract calculation*Minimum measurement
-
Product
PCI-6115, 4 AI (12-Bit, 10 MS/s/ch, Buffer Rate 32MS), 2 AO, 8 DIO, PCI Multifunction I/O Device
778554-01
-
4 AI (12-Bit, 10 MS/s/ch), 2 AO, 8 DIO, PCI Multifunction I/O Device - The PCI‑6115 is a simultaneous-sampling, multifunction DAQ device. It offers analog I/O, digital I/O, two 24‑bit counters, and digital triggering. The PCI‑6115 is ideal for a variety of applications, such as stimulus/response applications that require synchronization among analog input (AI), analog output (AO), and digital I/O. It is also ideal for 42 V automotive applications, radar, sonar, and ultrasound. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements. The PCI‑6115 dimensions require chassis slots that can accommodate full-length PCI modules.
-
Product
PCI-6521, 16-Channel, ±30 VDC, 8 Sink/Source Inputs, 8 Relay Outputs (150 V), Isolated Digital I/O Device
779312-01
-
The PCI-6521 is an industrial digital I/O module with high channel isolation and industry-standard 24 V logic levels. If a computer or application fault occurs, the PCI-6521 can use … digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. It also features programmable power-up states, digital filtering, and change detection for optimal control over your application.
-
Product
Parameter And Device Analyzers, Curve Tracers
-
Precision Current-Voltage Analyzer Series ensures accurate and efficient current-voltage measurements that give a clear insight into IV characteristics across a wide range of applications. The powerful characterization software and integrated source and measurements units (SMUs) make it much quicker and simpler to obtain accurate IV characterization. The EasyEXPERT group+ software supports all the characterization tasks such as measurement setup and execution, data analysis, data management and protection and so on, using the graphical intuitive user interface and mouse/keyboard operation. The Current Voltage Analyzers Series provides a wide selection of IV analyzers suitable to your specific current voltage measurement needs in the range from an economic model to the most advanced analyzer capable of supporting cutting-edge applications.
-
Product
USB-6363, 32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO USB Multifunction I/O Device
781443-01
-
32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO USB Multifunction I/O Device - The USB‑6363 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6363 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Compact Ultrasonic Testing Device
SONAPHONE® Pocket
-
With the SONAPHONE Pocket you identify problems even before they arise and create value at all levels of your company. Just by detecting and eliminating leaks you can reduce the energy costs for your compressed air system up to 30 percent. This also has positive effects on your operational safety and system productivity through early warning of bearing failure and evidence of partial electrical discharges.
-
Product
USB-6343, 32 AI (16-Bit, 500 kS/s), 4 AO (900 kS/s), 48 DIO USB Multifunction I/O Device
782252-01
-
32 AI (16-Bit, 500 kS/s), 4 AO (900 kS/s), 48 DIO USB Multifunction I/O Device - The USB‑6343 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6343 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PCIe-6323, PCI Express, 32 AI (16-Bit, 250 kS/s), 4 AO (900 kS/s), 48 DIO Multifunction I/O Device
781045-01
-
PCI Express, 32 AI (16-Bit, 250 kS/s), 4 AO (900 kS/s), 48 DIO Multifunction I/O Device - The PCIe‑6323 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PCIe‑6323 is well-suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PCI-6154, 4 AI (16-Bit, 250 kS/s/ch), 4 AO, 6 DI, 4 DO, PCI Multifunction I/O Device
779340-01
-
4 AI (16-Bit, 250 kS/s/ch), 4 AO, 6 DI, 4 DO, PCI Multifunction I/O Device - The PCI‑6154 is a simultaneous-sampling, channel-to-channel isolated DAQ device. It offers analog I/O, digital input, digital output, two 32‑bit counters, and digital triggering. You can combine the channel‑to‑channel isolated analog outputs to generate signals greater than ±10 V (up to ±40 V by combining all four channels). The PCI‑6154 is ideal for a variety of applications including automotive test, industrial monitoring and control, and high-speed continuous data logging. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
