Flash Device
-
Product
USB-8502, 2-Port, High-Speed/FD, USB CAN Interface Device
784662-01
CAN Interface
1- or 2-Port, High-Speed/FD, USB CAN Interface Device—The USB-8502 is a high-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8502 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8502 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
USB-6255, 80 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device
779959-01
Multifunction I/O
80 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device - The USB‑6255 offers analog I/O, digital I/O, two 32-bit counters/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PCI-6521, 16-Channel, ±30 VDC, 8 Sink/Source Inputs, 8 Relay Outputs (150 V), Isolated Digital I/O Device
779312-01
Digital I/O
The PCI-6521 is an industrial digital I/O module with high channel isolation and industry-standard 24 V logic levels. If a computer or application fault occurs, the PCI-6521 can use … digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. It also features programmable power-up states, digital filtering, and change detection for optimal control over your application.
-
Product
PCIe-6509, PCI Express, 96-Channel, 5 V, TTL/CMOS, 24 mA Digital I/O Device
779976-01
Digital I/O
The PCIe-6509 can directly drive external digital devices such as solid-state relays (SSRs). You can configure each port for input or output, and no external power supply is required for outputs. Using programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators. If a computer or application fault occurs, the PCIe-6509 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
Measuring Devices for Magnetically Soft Materials
MAG-RJJ-6.0
-
The computerized measuring system is designed for measure the dynamic magnetic properties of the soft magnetic materials e.g. oriented or not-oriented electrical sheet. The system provides the opportunity of a tabular and graphic presentation of the obtained data, which can be presented by means of monitor, printer or plotter.
-
Product
PCIe-7821, Kintex 7 FPGA, Digital Reconfigurable I/O Device
785359-01
Digital I/O
The PCIe‑7821 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PCIe‑7821 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in-‑the‑loop (HIL) test, bit error rate test, and other applications that require precise timing and control.
-
Product
PCI-5153, 500 MHz Bandwidth, 2 GS/s, 8-Bit PCI Oscilloscope Device
780318-01
Oscilloscope
500 MHz Bandwidth, 2 GS/s, 8-Bit PCI Oscilloscope Device - The PCI‑5153 high-speed oscilloscope device has two channels that sample up to 2 GS/s with flexible settings for coupling, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require up to 500 MHz of analog bandwidth and flexible measurement configurations.
-
Product
SSD - Solid State Storage Devices
-
LinkedHope Intelligent Technologies Co.,Ltd.
LinkedHope Intelligent Technologies SSD Products
-
Product
CCD Device Handlers
-
Exatron has been in a unique position to supply handling systems for the new CCD device market. Manufacturers of CCD devices came to Exatron when these devices were new, looking for custom handling applications, and Exatron responded by modifying its Model 3000B, 3000BL, 5000, 5080, and 8000 systems to accommodate CCD devices.
-
Product
PCIe-5775, 12-Bit, 6.4 GS/s, 2-Channel PCI FlexRIO Digitizer Device
785593-01
FlexRio Digitizer
The PCIe-5775 is a PCI FlexRIO Digitizer Device that provides 6 GHz of AC-coupled analog bandwidth and 12 bits of resolution. You can operate the PCIe-5775 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. With a passband from 1 MHz to more than 6 GHz, the PCIe-5775 is ideal for high-bandwidth frequency domain applications, including radar prototyping, LIDAR, and communications.
-
Product
IEC60335-2-4 100mm Drop Test Device With 40I - 50I RHD Galvanized Steel Hammer
CX-21673
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60335-2-4 100mm Drop Test Device With 40I - 50I RHD Galvanized Steel Hammer
-
Product
USB-4065, 6½-Digit, ±300 V, USB Digital Multimeter Device
780152-01
Digital Multimeter
The USB‑4065 makes AC/DC voltage, AC/DC current, and 2‑ or 4‑wire resistance measurements, as well as diode tests. It is ideally suited for OEMs, educational laboratories, or other cost-conscious test and measurement applications.
-
Product
Differential And I/Q Device Measurements
S95089B
-
The S95089B combines source-phase control of multiple internal or external sources with frequency-offset mode, enabling simplified test of I/Q modulators/converters, differential mixers, and harmonics or amplifiers.
-
Product
*PCIe-5785, 12-Bit, 6.4 GS/s, 2-Channel FlexRIO IF Transceiver Device
785589-02
FlexRIO IF Transceiver
The PCIe-5785 enables direct RF acquisition up to 6 GHz and generation up to 3 GHz with 12 bits of resolution. You can use it in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The PCIe-5785 is ideal for applications that require wideband acquisition and generation with multichannel synchronization, including radar, electronic warfare, and communications. The FlexRIO driver includes support for acquiring and generating waveforms out of the box, and you can use the LabVIEW-programmable Xilinx Kintex UltraScale FPGA to implement custom algorithms for real-time signal processing.
-
Product
PCI-5105, 8‐Channel, 12-Bit, 60 MHz Bandwidth PCI Oscilloscope Device
779686-02
Oscilloscope
8‐Channel, 12-Bit, 60 MHz Bandwidth PCI Oscilloscope Device—The PCI‑5105 high-density oscilloscope device has eight simultaneously-sampled channels with flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with many channels that require up to 60 MS/s or 60 MHz of analog bandwidth.
-
Product
GPIB-RS232, Instrument Control Device - Taiwan 110VAC
779732-11
GPIB Controller
The GPIB‑RS232 is an IEEE 488 controller device for computers with an RS232 port. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS232 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS232 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488 and RS232 standards, as well as interpret and execute high-level commands from the serial port, including RS232‑to‑GPIB and GPIB‑to‑RS232 protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
50 MHz to 2.2 GHz, Reconfigurable USRP Software Defined Radio Device
783923-01
Communications Module
50 MHz to 2.2 GHz, Reconfigurable USRP Software Defined Radio Device - The USRP-2940 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless communication systems. Built on the LabVIEW reconfigurable I/O (RIO) architecture, USRP RIO delivers an integrated hardware and software solution, so researchers can prototype faster and significantly shorten time to results. You can prototype a wide range of advanced research applications that include multiple input, multiple output (MIMO); synchronization of heterogeneous networks; LTE relaying; RF compressive sampling; spectrum sensing; cognitive radio; beamforming; and direction finding.
-
Product
Flexible Test And Scan Solution For FFC Devices
Ismeca NY32W
-
32-position turret test and scan platform for semiconductors on film-frame wafer media, providing the highest inspection yield for WLCSP and Bare Dies. Integrating innovative hardware and software technologies such as intelligent features that enable extended autonomous operation and productivity.
-
Product
Ferrite Devices
-
Ducommun's products include very broad ferrite device selections to cover 100 MHz to 110 GHz operation frequency range. These devices include narrow band drop-in (FID and FCD), connectorized (FIC and FCC), junction (FIW and FCW) isolators and circulators and iso-adapters (FII and FCI). The broad bandwidth versions are offered as full band junction isolators and circulators (FIF and FCF) and Faraday isolators (FFF). These devices feature low insertion loss, high isolation and wide operating temperature range. Low cost and volume production versions of these ferrite devices are available per customers’ request.
-
Product
Active Device Characterization Solution Up To 67 GHz
N5247BM
-
The N5247BM provides the N5247B 67 GHz PNA-X network analyzer, application software and accessories for active device characterization up to 67 GHz.
-
Product
Insulation Measuring Device According to DIN EN 61557-2 (VDE 0413-2)
-
PeakTech Prüf- und Messtechnik GmbH
This digital insulation measuring device is required for various measurements of cables, components and their insulation.
-
Product
GPIB-ENET/1000, Ethernet GPIB Instrument Control Device - United Kingdom 240VAC
781630-06
GPIB Controller
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
Smart Device Testing
-
Helping you ensure that your smart devices with integrated wireless modules meet requirements to demonstrate compliance to global wireless type approval requirements.A smart device is any piece of electronic equipment that intentionally communicates and interacts with other electronic devices using wireless protocols. In order to verify the performance and connectivity of these devices, both the device hardware and the communication protocol are evaluated to ensure smooth connectivity and eliminate unacceptable interference.
-
Product
System Devices for Radiomonitoring
-
Monitoring stations need auxiliary equipment to ensure optimal alignment and control of the antenna or antennas or to provide users with RF signal filtering functions close to the antenna, depending on requirements. Customers around the world use the innovative system devices for monitoring stations from Rohde & Schwarz to meet these requirements. These devices stand for performance, quality, flexible deployment options and a wide range of possible configurations, which is why they are an optimum solution for any radiomonitoring application when used in conjunction with the other products in the Rohde & Schwarz radiomonitoring and radiolocation portfolio.
-
-
Product
Jaw Device
PC-100
-
The PC-100 device is designed to determine the taper and the crown of generator core lamination. The device contain series connection which allow the data transmittion to PC.
-
Product
PCIe-8433, PCI Express, 2-Port, Isolated, RS485/RS422 Serial Interface Device
781745-01
Serial Interface
The PCIe‑8433/2 is a high-performance industrial interface for high-speed, port‑to‑port isolated communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
USB-8501, 1-Port, Low-Speed/Fault Tolerant, USB CAN Interface Device
786306-01
CAN Interface
The USB-8501 is a low-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8501 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8501 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
PCIe-8510, 2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device
785324-01
Interface
2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device—The PCIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PCIe‑8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
PCI Express, Analyzer Software Included, IEEE 488 GPIB Instrument Control Device for Windows - Onboard GBIP Analyzer
780935-01
Signal Analyzer
The PCIe‑GPIB+ combines an IEEE 488 controller and an analyzer on one device for computers with PCIe slots. You can use this device to integrate an instrument into your system using GPIB as well as to troubleshoot and solve GPIB hardware and software problems. The PCIe‑GPIB+ achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
