-
Product
Cement Compression & Flexural Testing Machines
-
The Compression & Flexural testing product line from Qualitest offers a wide variety that will fit almost any budget. Different options between models include digital or analog display, single or dual range, and different types of configurations. All the Compression & Flexural testing machines conform to international standards for compressive & flexural tests.
-
Product
High-Temperature Strain Gages
ZWH-, ZWN-, & ZWP-Series
-
ZWH-, ZWN-, and ZWP-Series strain gages are designed for dynamic and limited static strain measurement at hightemperature.These strain gages are manufactured using a round wire for superior bonding ability and performance. A high-fatigue wire (Option Z) is also available on each of the gages. These gages are supplied with a fiberglassreinforced tape carrier which holds the grid and leads in place during installation and are bonded using ceramic cements or Rokide® flame spray. The shelf-life of thesegages is 9 months.
-
Product
Fluid Loss
-
Fluid Loss testers were designed to be as easy to use as possible, with clear and intuitive controls. Once the cement slurry or mud is placed into the test cell, a programmable temperature controller increases the temperature at the desired rate.
-
Product
Single Screw Electromechanical Universal Testing Machine
CMT Series
-
Jinan Testing Equipment IE Corporation
The CMT series single screw testing machine is designed for mechanical property test mainly on metal materials, cement, asphalt, and bitumen etc. A variety of fixtures can be offered to do compression, bending and shearing test as well. This series of single screw testing machine is suitable for the applications in quality inspection, research, metallurgy, rubber & plastics, and knitting materials, and widely used in many fields such as industry factories, mineral enterprise and high schools.
-
Product
Stack Gas Analyzer
ENDA-7000 Series
-
After decades of experience in precise stack gas measurement, HORIBA's brand new ENDA series represents the ultimate stack gas analyzer. With enhanced lower cost and reduced maintenance time, high sensitivity, and usability, we focused on the users' point of view. The ENDA-7000 is designed to continuously measure the concentrations of NOX, SO2, CO, CO2, O2, and NH3 in stack flue gas streams. The model is offered in dozens of combinations based on your measurement requirements. The ENDA-7000 uses an extractive method which measures undiluted sample gases, and is very suitable to stack gas measurements such as shale gas, LNG, or biogas and other combustion applications. The ENDA-7000 is an excellent choice for measurements in power generation facilities, boilers, furnaces, steel manufacturing, cement plants, pulp and paper mills, etc.
-
Product
Concrete Drainpipe Compression Testing Machine
SCT Series
-
Jinan Testing Equipment IE Corporation
The concrete drainpipe compression testing machine is designed for the radial compression test of drainpipe and other cement pipes which accords with "Test method of concrete and ferroconcrete drainpipe":. The concrete drainpipe compression testing system is also suitable for the compression test of other metal and non-metal materials. The concrete drainpipe compression testing machine consists of load frame, oil source, computer and servo unit. It is of compact structure and easy to operate.
-
Product
Electronic Moisture Analyzer
MOC-120H
-
The moisture content of a variety of samples can be measured using an array of drying modes. The drying status can be seen at-a-glance with the fluctuation range display. Active in a variety of fields (cereals, starch, flour, noodles, brewed products, sea foods and marine products, meat products, spices, sweets, dairy products, dried foods, vegetable oils and other food articles; pharmaceuticals; ores; cokes; glass materials; cement; chemical fertilizers; pulp and paper; cotton; various fabrics and other industrial goods); enabling measurement of samples (cereals, foods, and chemical products) under various conditions (powder, particles, paste, and liquid).
-
Product
Moisture Meters
-
Sper Scientific’s moisture meters accurately read the moisture content of all types of wood but of cement, plaster, brick and concrete. Home and building inspectors rely on moisture meters to identify potential problems and damage to structures from moisture buildup. Woodworking industries, such as furniture makers, use wood moisture meters to insure a quality product.
-
Product
CEMS II E Continuous Emission Monitoring System
-
CEMS II e takes away the manual configuration and settings adjustments from your day-to-day emissions measurements. A fully automated continuous emission monitoring system CEMS II e is TÜV and MCERTS certified solution (QAL1) to offer environmental compliance. This emission monitoring system is suitable for measuring pollutants continuously from hot, wet and corrosive gas streams in various industrial processes, such as powerplants, waste incineration, cement plants and beyond.
-
Product
Building Electronic Thermometer
NF-514
-
Shenzhen Noyafa Electronic CO.,LTD
*Cement Concrete Professional Thermometer.*Built-in LCD Lighting Function: Working in harsh environments, clear readings.*Exquisite material selection and lightweight design.*Built-in Temperature Measuring Line, Durable and High Temperature Resistance.*Embedded Line Asphalt Temperature Measurement.*Small size,light weight, easy to carry, suitable for construction sites and field operations.*Certification. Passes RoHS, FCC, and CE compliance testing, and Noyafa is certified to the ISO 9001 standard.*100% Affordable. Manufactured in China and a lot cheaper than competitor products with similar quality.
-
Product
Arc Infrared Carbon and Sulfur Analyzer
CS-8620
-
Wuxi Jinyibo Instrument Technology Co., Ltd.
Infrared carbon and sulfur analyzer is used together with high-speed automatic ignition furnace to quickly and accurately determines the mass fraction of carbon and sulfur in steel, iron, alloy, non-ferrous metals, cement, ore, catalyst and other materials. a high-tech product integrating light, electromechanical, computer and analytical technology. It has the advantages of wide measuring range, strong anti-interference ability, complete functions, simple operation, accurate and reliable analysis results, etc. It is the ideal for measuring Carbon and sulfur in many industries. Analytical equipment.
-
Product
Viscosity/Rheology
-
Well known for producing the world's most capable and reliable high pressure, high temperature (HPHT) well cementing instruments, the Chandler Engineering portfolio of instruments and systems has grown to include reservoir testing systems, drilling fluid testing and corrosion testing instruments as well as many other unique solutions for reservoir evaluation, well construction and completions. Click on one of the below options for additional information:
-
Product
Carbon / Water Analyzer
CW‑800
-
Determination of released carbon dioxide and water is a special requirement for quality control in the cement and lime industry. ELTRA’s CW-800 analyzer is designed for the precise, simultaneous determination of carbon dioxide and water in lime, gypsum and cement from trace level up to 100 % (depending on sample weight). Other sample materials include ores, soil and minerals. The CW-800 is equipped with a resistance furnace with quartz tube for sample oxidation and can provide temperatures up to 1000 °C. The temperature of the CW-800 can be set up in steps of 1 °C and the temperature is fixed during measurement. As common carrier gas in the CW-800 nitrogen is used.
-
Product
Microwave Moisture Meter
RX-95
-
The system works based on the absorption of microwave energy by water molecules contained inthe x-rayed material. It is a non-contact, non-destructive method of instant measurement of water content - used for materials such as coal, flour, grain, cement, seeds, sugar, etc. Thanks to high measurement sensitivity (resolution greater than 0.01% of water content by weight), short measurement time (about 5 times/sec.) and repeatability of measurement - the system is suitable for continuous measurement of material moisture, e.g. on conveyor belts and its recording on a PC or using a 4-20 mA current loop.
-
Product
Scratch Tester
CSR1000
-
This tester is highly effective in measuring the adhesion strength (adhesion strength) of hard coatings (Ti, TiN, SiC, DLC, etc.) formed by PVD and CVD on metal surfaces such as cemented carbide. Adopting a scratch test method that allows quantitative measurement with simple operations, the film surface is scratched while increasing the load on the sample surface, detecting film breakage with high sensitivity, and providing the load at which film breakage occurs (critical load). tools and mold tools that require
-
Product
zeta potential analyzer
ZetaProbe Analyzer™
-
The ZetaProbe is the easiest to use, most accurate zeta potential analyzer available. Samples can be measured without dilution or sample preparation at concentrations up to 60% volume. Even the direct measurements of pastes, gels, cements, and other difficult materials are possible with the ZetaProbe.
-
Product
Universal Calibrators
-
We offer our clients an exclusive range of Universal Calibrators which is designed and manufactured by our technical team. Our range is designed using superior quality material, and is widely appreciated for its rugged designs and durability. Also, these are presented with dual operating ability of source & sink of signals that make them appropriate for labs and process plants. Further, our assortment is extensively used in the calibration of instruments, commissioning of field instruments, repair & maintenance of filed instruments and as millimeter with limited facilities in various industries, such as chemical, cement, textile, fertilizer and automobile.
-
Product
Mill & Silo Monitoring System
MSM-100
-
MSM-100 is a monitoring system specifically designed to continuously detect carbon monoxide(CO) in pulverizing mills. The high level of CO produced by any incomplete combustion process, is used by the MSM-100 system as advance warning of a mill fire. It is suitable for any coal or peat system where advance warning of spontaneous combustion is required. MSM-100 is intended for operation in the electricity, metals, cement, steel and processing industries.
-
Product
Moisture Testing
-
Determine moisture in concrete and other construction materials. Meter for rapid determination of moisture content in sand and other fine or coarse aggregates. moisture content in Solid Materials. Includes Meter, Test Cable and Case. Meter for the Rapid Determination of Moisture Content in Different Types of Soil. Determination of Water/Cement Content Ratio in Fresh Concrete. (Type R for Regular Water Cement Ranges. Type L for Low Water Cement Ranges.)
-
Product
Image Analysis Software
Metallurgy Plus
-
International Biological Laboratories
his software can be used in Steel plants, Metal forging industry, Oil & gas industry ,Material Science, Mineralogy - metal and metal strength analysis Cement (Klincker) quality control and where ever Metallurgical microscope are used in .This Package is very useful Educational Institutions and ALL MATERIAL SCIENCE TECHNOCRATS AND METALLURGISTS.
-
Product
Tunable Laser Hydrogen Chloride Analyzer
TX-100
-
Laser HCl analyzer with a probe type optical system which employs direct insert method. TX-100 is suitable for monitoring HCl concentration in incineration plants and the control of HCl removal process in various industries including cement factories and petrochemical plants, etc.
-
Product
Mechanical Properties
-
Mechanical Properties Analyzers (MPRO) continuously measures the elastic mechanical properties (Poisson's Ratio, Young's modulus, Bulk Modulus) and the compressive strength of API cement as it cures under high-temperature and high-pressure conditions.
-
Product
Carbon / Water Analyzer
CW‑800M
-
ELTRA’s CW-800M analyzer is designed for fractional analysis of carbon and water in one single operation. It is based on the proven technology of the CW-800 but has a modified furnace which allows fast adjustment of the temperature in the furnace. Different fractions of carbon and water of the sample are analyzed by applying different furnace temperatures. ELTRA’s CW-800M analyzer is designed for the precise, simultaneous determination of carbon (released as CO2) and water in lime, gypsum and cement from trace level up to 100 % (depending on sample weight). Other sample materials include ores, soil, minerals, slags and waste.
-
Product
Precision Current Sensing Resistors
PCR4T
-
Precision cement resistors designed with four terminals, are distinguished by excellent long term stability & TCR. The Kelvin connections of this device allow high precision measurements even with low resistance values. PCR 4T has a non-inductive copper manganin element inserted into the ceramic case and finally sealed with a ceramic molding. This resistor has low inductance and has high pulse power.
-
Product
Whiteness Meter
-
Guangzhou Amittari Instruments Co.Ltd
AMITTARI l Whiteness Meter is mainly used to directly measure the whiteness value of object or powder with flat surface. It can be widely used in whiteness measurement of textile printing and dyeing, paint, chemical building materials, paper board, plastic products, white cement, ceramics, enamel, talc powder, starch, flour, salt, detergent, cosmetics and other substances. The instrument pass strict inspection and testing, conforms to the JJG 512-2002 Whiteness Meter Verification Regulation. Also conforms to GB3978、GB3979、GB7973、GB7974、ISO2470、GB8904.2、QB1840、GB2913、GB13025.2、GB1543、ISO2471、GB10339、GB5950、GB12911、GB2409 and other standards.
-
Product
Automatic Compression Testing Machine
CTEN Series
-
Jinan Testing Equipment IE Corporation
This series compression testing machine is mainly designed for compression test of building material items, such as concrete cube, concrete blocks, cement specimen, and bricks etc, also used for compression performance test of rubber pad and top forge test of metal. With new design idea and advanced technology, this series have more advantages in appearance, operation & applications. It is the ideal test equipment for quality control at industry & mineral enterprises, education in high schools, and technology researches at scientific institutes
-
Product
Hydraulic Servo Control Compression Testing Machine (Four Column)
TYE Series
-
Jinan Testing Equipment IE Corporation
This series Servo-Hydraulic Compression Testing Machine is mainly designed for compression test of building material items, such as concrete cubes, cement specimen, paver materials and related component, etc. With new design idea and advanced technolog, this series has more advantages in appearance, operation & applications. The compression testing machine is an ideal tester for quality control at industrial & mineral enterprises, teaching in high schools, and technology researching at scientific institutes.
-
Product
Cement Testing Equipment
-
High quality cement is necessary to produce concrete and mortar that meets relevant construction industry specifications. ELE international designs and manufactures a wide range of sample preparation and cement testing equipment which complies with global standards for the assessment of fineness, consistency, setting time, workability, flow, strength, soundness, heat of hydration and chemical composition.
-
Product
CMM AutoQAL & CMM Continuous Mercury Monitoring Systems
-
Continuous Mercury Monitoring systems, the CMM and CMM AutoQAL, are TÜV and MCERTS certified solutions for continuous mercury monitoring from hot, wet and corrosive gas streams of industrial processes, such as waste incineration, cement production and powerplants. Gasmet offers a full CMM solution package which consists of a system, lifetime service and support, documentation and training, and our expertise.
-
Product
Medium Voltage Drives
-
Target markets include Oil and Gas, Water and Wastewater, Power Generation, Rubber and Tire, Mining, Cement and other industrial applications. They can be applied equally well to applications requiring Constant Torque (CT) output performance as well as the traditional Variable Torque (VT) pump and fan loads.
