-
Product
ESU Analyzers
-
Most ESU generators have multiple output modes with different waveforms, such as Cut, Coag, Bipolar, etc. Some of the waveforms are continuous and some are pulsed. The pulsed mode outputs of the following generators have been analyzed and found to be compatible with the indicated ESU Analyzers. Note that continuous waveforms can be measured by any analyzer, the compatibility list shown below is for pulsed waveform measurement.
-
Product
Ionization Sources
-
BaySpec offers many types of ionization sources to use with our Portability™ and Continuity™ portable mass spectrometers. Delivering ultimate mobility and ease of use, BaySpec’s Portability™ and Continuity™ are compatible with ambient ionization techniques, which do not require any gases or tanks to run measurements. Making it ideal for field analysis, ambient ionization does not require sample preparation; sample introduction quick, direct, and easy to perform by anyone in any location. Providing flexibility to perform applications using various ionization techniques, the external ionization sources can also easily be swapped in less than a minute.
-
Product
96/48/24-CH Opto-22 Compatible Digital I/O PCI Cards
PCI-7296/7248/7224
Digital I/O Module
ADLINK"s PCI-7296/7248/7224 are high-density parallel digital I/O boards with 96/48/24 I/O channels. The header connectors are fully compatible with industry Opto-22 standard. Thus, PCI-7296/48/24 can utilize the Opto-22 external devices. The PCI-7296/7248/7224 devices emulate mode 0 of the industry standard 8255 programmable peripheral interface (PPI) chips. The PCI-7296/7248/7224 provides 4/2/1 PPI chips respectively. Each PPI offers three 8-bit ports: Port A, Port B and Port C. The Port C is divided into 2 nibble-wide (4-bit) ports. The PCI-7296/7248/7224 devices have programmable timer/counters. One 16-bit counter is available for event counting, while the other 32-bit timer is available for timed interrupt generation. The PCI-7296/7248/7224 devices provide multiple programmable interrupt sources from DIO channels, as well as the output of the timer.
-
Product
USB-232/4, 4-Port, USB, RS232 Serial Interface Device
778473-04
Serial Interface
The USB‑232/4 interface transforms your USB port into a single asynchronous serial port for communication with RS232 devices. You can use a USB‑232/4 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Compliance Test Systems
LMG Test Suite
-
ZES ZIMMER Electronic Systems GmbH
The ZES ZIMMER test system LMG Test Suite tests in accordance with the currently valid version of EN 61000-3-2/-12 or EN 61000-3-3/-11 and also supports measurements per ECE R-10.4 Annex 11 (e.g. electromagnetic compatibility of vehicles). As a manufacturer of precision power measurement technology, we are represented on the international standards committee. As a result, changes in standards are immediately incorporated into our test systems.
-
Product
Penetration Testing Distrubution
BlackArch Linux
-
BlackArch Linux is an Arch Linux-based penetration testing distribution for penetration testers and security researchers. The repository contains 1524 tools. You can install tools individually or in groups. BlackArch Linux is compatible with existing Arch installs. For more information, see the installation instructions.
-
Product
DCDC
GA Series
-
The GA series is an economically priced 15 watt DC/DC converter featuring ultra-wide input range, efficiencies to 85% and a continuous six-sided shielded case. Low ESRcapacitors are used both on the input and the output(s) to minimize the conductive noise. Other key features include: overvoltage protection, output trim adjustability, TTL and CMOS compatible remote on/off, short circuit protection and small size. The GA series measures only 1.6” x 2.0” x 0.40” and offers a power density of 11.7 watts/cu. in.
-
Product
TPMS Diagnostic Tools
-
An advanced diagnostic tablet compatible with U.S., Asian and European vehicles, 1996 and newer. This wireless Android-based touchscreen tablet performs comprehensive TPMS servicing including 1-Sensor programming to its extensive vehicle diagnostics capability including an all systems scan with ADAS identification, the ability to read/erase codes, view freeze frame and live data, bi-directional control including active testing, coding and adaptations.
-
Product
PCIe FPGA Carrier For FMC, Virtex-7
PCI516
-
The PCI516 is based on the Xilinx Virtex-7 690T, which provides 3,600 DSP slices, 52,920 Kb RAM and 690,000 logic cells. The FPGA interfaces directly to the FMC DP 0-9 and all FMC LA/HA/HB pairs, making it compatible with a wide range of industry standard VITA 57 modules. It also has interface to three DDR3 memory channels (64-bit wide and 16-bit wide). This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host. The unit has x8 PCIe edge connector routed to the FPGA PCIe Gen3 hard IP block. In addition, 16 uncommitted connection pairs are routed to a dual x8 expansion connector, providing direct connectivity to a neighbouring FPGA (e.g. via Aurora, 10 G/40 G, SRIO, PCIe) without the need to go through the host.
-
Product
Solenoid Tester
-
FISHER TESTERS AUTOMATIC TEST EQUIPMENT
• Touch Screen Interface• Windows® 10 Pro• High Reliability with Proven Design• USB Interface – No I/O boards in Computer• Remote Control Software for Factory Diagnostics/Updates• Full Network Compatibility• Integral Statistical Reporting• Test Data May be Stored in Multiple Formats• Two Year Warranty on Electronics
-
Product
PCIe and VPX Compatible Adapter Carrier
PCIe2VPX3UX4
-
The power supply designs utilize switching regulators controlling MOSFET´s. An LC filter insures clean power at the VPX device. The PCIe gold fingers are rated for 1.1A each, and a total of 5.5A on the +12V rail. 55W are available to the card after power conversion.
-
Product
5-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB105
-
The FAB105 features a PICMG 1.3 CPU card slot, one PCI Express x16 slot, three 32bit/33MHz PCI slots, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. The FAB105 is perfect fit for AXIOMTEK's SHB100 and SHB110, which are built around the PICMG 1.3 form factor. The FAB105 is compatible with the AX60501 chassis.
-
Product
Receiver, G12, 12 Module, 15" Platform, for Slide Mount
310104325-1
Receiver
Receiver, G12, 12 Module, 15" Platform, for Slide Mount (slide kit required)**Please note - This part number ships with the platform not attached to the receiver. Platform must be assembled after delivery. The 15" G12 Receiver is a slide-mounted receiver. The 15" platform provides a surface to hold fixtures or other tools and supports up to 180 lbs. The 15" platform configuration is not compatible with the optional leg kit.This part number includes: G12 Receiver 15" Platform Mounting brackets (for attaching slide kit to platform) Left side microswitchSlide kit, keying kit, instrument bracket, right side microswitch, and any other accessories must be purchased separately. Designed for VPC 90-Series modules.
-
Product
Communications Manufacturing Test Set
CMW100
-
The R&S®CMW100 communications manufacturing test set is based on the R&S®CMW platform. The flexible RF interface permits simultaneous testing of up to eight devices. The R&S®CMW100 remote control and measurement concepts are compatible with the R&S®CMW500. The R&S®CMW100 is optimized for cost-effective calibration and verification of wireless devices in non-signaling mode (analyzer/generator). The tester provides a new eco-friendly hardware concept, featuring extremely low energy consumption and a very compact size, making it ideal for use in fully automated robotic production lines. It supports LTE, 5G NR, WLAN, Bluetooth® and IoT technologies, making it ready for today and tomorrow.
-
Product
CFML Test Framework
TestBox
-
TestBox is a next generation testing framework for ColdFusion (CFML) that is based on BDD (Behavior Driven Development) for providing a clean obvious syntax for writing tests. It contains not only a testing framework, runner, assertions and expectations library but also ships with MockBox, A Mocking & Stubbing Framework. It also supports xUnit style of testing and MXUnit compatibilities.
-
Product
High Speed VNIR/SWIR Hyperspectral Imager
-
Compact VNIR/SWIR HSI sensor compatible with small rotary wing UAS operation with application to disturbed earth detection and vegetation/mineral mapping
-
Product
Controller PCI
IIB-429-PCI
-
The IIB-429-PCI provides four ARINC-429 compatable channels (2 receive and 2 transmit) at any rate between 12.5 and 100kbps. Because the IIB-429-PCI is built upon a flexible platform, user functions can be implemented almost without restriction, making this product flexible and user-friendly.
-
Product
Software
DV-Win
-
An unique software application called DV-Win has been developed by DV Power as a tool compatible with all series of our instruments. Software automatically recognizes the device which is connected to a PC and activates appropriate form.
-
Product
GPIB-USB-HS+ , USB, Analyzer Software Included, IEEE 488 GPIB Instrument Control Device
783368-01
GPIB Controller
USB, Analyzer Software Included, IEEE 488 GPIB Instrument Control Device - The GPIB‑USB‑HS+ is an IEEE 488 controller and portable analyzer device for computers with USB slots. You can use this device to integrate an instrument into your system using GPIB as well as to troubleshoot and solve GPIB hardware and software problems. The GPIB‑USB‑HS+ achieves maximum IEEE 488.2 performance. With no GPIB cable required for instrument connection, you can use the Hi‑Speed USB port to control up to 14 programmable GPIB instruments. The improved design allows for size compatibility with almost every instrument, adds analyzer functionality, and reduces the overhead to generate faster turnaround times in your application. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
Hawk - E Co Processor
9322 E
-
Basic Hawk Co-Processor card set with 2.0 Mbyte memory and microcoded instructions for Nova 4X and Eclipse S280. Executes ALU instructions in 275 nanoseconds. ISA bus compatible, two slots required. Approximate CPU performance of actual S280.
-
Product
Powered VME430 Crates
6U VME430 195 Mini
-
The VME195-C mini crate is the perfect choice for a small CERN V430 compatible setup. The crate offers 9 VME slots in compact designed chassis with integrated low noise power supply and cooling fan. It can be used either as a desktop / mini tower or 19" rack mounted.
-
Product
3 Mm Glassy Carbon Disk Electrode
CGC1
-
3 mm glassy carbon disk electrode designed for electrochemical research, cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), corrosion studies, electrocatalysis, and sensor development. Manufactured from high-purity glassy carbon with excellent chemical stability, a wide potential window, and low background current. Compatible with CHI104 systems and customizable for laboratory and OEM applications.
-
Product
Microcontrollers
-
Panasonic Industrial Devices Sales Company of America
Based on a rigorous analysis of embedded device software and system needs, the Panasonic AM1 (MN101C/MN101E/MN101L) and AM3 (MN103H/MN103S/ MN103L) Series signal a new concept in Microcomputer design. With 8-bit and 32-bit models that share a unified architecture, Panasonic Microcomputers combine high performance with low power consumption in a package that supports C-language programming for a fast, efficient development cycle. Since the instructions for MN103H/MN103S and MN101C/MN101E are respectively compatible with MN103L's and MN101L's, the programming data can be inherited to achieve efficient system development. Panasonic Microcomputers feature a single development environment and are suitable for a wide range of applications, including high-performance embedded controllers and key devices in multimedia hardware.
-
Product
PS/2*2 Redundant Power; ATX 400W
PS401-HRP
-
*Input Range: 90 ~ 264Vac Full Range*Output Voltage:**+5V, 35A (5A min)**+3.3V, 28A (1A min)**+12V, 20A (2.5A min)**-12V, 1A**-5V, 0.8A**+5Vsb, 2A (0.1A min)*MTBF(hours): 100,000h*Safety: UL, TUV, CE, CSA*Dimensions: 183 x 167 x 187.8 mm*Compatible with Axiomtek products: AX61492
-
Product
USB Sensor Link
90386
-
The 90386 is a portable sensor interface that powers and processes strain gaged based sensor into USB compatible signals. No need for additional signal processing or special PC cards.
-
Product
Variable Attenuator
FTBx-3500
-
Network equipment manufacturers and transceiver manufacturers know that variable attenuators are essential components of their test systems. They look for performance, user-friendliness, complete control of test parameters and advanced programming capability. EXFO’s FTBx-3500 Variable Attenuator combines innovative design techniques, high-quality components and meticulous calibration procedure. Ideal for bit error rate testing and system verification, the FTBx-3500 is the only variable optical attenuator (VOA) that offers a fully remote user interface (UI) and EXFO Multilink compatibility. It is also the only VOA on the market to offer a benchtop unit, which can be controlled remotely or using a touchscreen.
-
Product
32G DDR4-3200 2GbX8 1.2V SAM -40~85C
AQD-D4U32N32-SBW
-
DDR4 3200Mhz Unbuffered DIMM, 30u" Gold Plating Thickness, Anti-sulfurization resistance. 1.2V power consumption, Samsung original chip, 100% tested for stability, compatibility and performance.
-
Product
Audio Meter and Side Chaining Tool
Digital Peak Meter Pro
-
The metering capabilities of the DPMP plug-in let you control and monitor your audio signal exactly the way you want: almost every aspect of the meters can be customized. It now proposes five different scales, including Bob Katz's very popular K-System scales (K-12, K-14, K-16 and also the extra K-10). The graphs show the evolution of the audio envelopes over time, and the mid-side switch lets you verify mono compatibility problems and check the "stereoness" of your audio sources very easily.
-
Product
USB-485/4, 4-Port, USB, RS485/RS422 Serial Interface Device
778476-104
Serial Interface
The USB‑485/4 interface transforms your USB port into a single asynchronous serial port for communication with RS485 and RS422 devices. You can use a USB‑485/4 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Additional Products: 26 Pin D-Type Connectors
-
The connectors below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
