Device Programmers
Program non-volatile memories, logic devices, microprocessors and other electrically-programmable devices.
See Also: Programmers
-
product
PXI/PXIe 15W Programmable Resistor Module
42-254-022
The 40-254-022 (PXI) and 42-254-022 (PXIe) are programmable resistor modules with 1 channel which can be set between 1.5Ω and 1.81kΩ with 0.5Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
product
Programmable, 2-Channel Low-Pass Filter Module
AAF-3F
Programmable, 2-Channel Low-Pass Filter Module. The AAF-3F is designed for use with the AAF-3M and AAF-3PCI filter boards.
-
product
PCI Precision Resistor Card 6-Channel, 3Ω To 11.4MΩ
50-297-053
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Ethernet USB Device Server
DS-520AN
The DS-520AN is a USB Device Server supporting 802.11n Wireless LAN or Gigabit Ethernet Wired LAN Networks. Any USB device can be used over a wired/wireless network with the DS-520AN just as though it was connected to a computer.
-
product
PXI/PXIe 15W Programmable Resistor Module
42-254-115
The 40-254-115 (PXI) and 42-254-115 (PXIe) are programmable resistor modules with 1 channel which can be set between 1Ω and 920Ω with 4Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
-
product
Partial Discharge Detection Calibration Device
Hangzhou Xihu Electronic Institute
Calibration Device of Transient Earth Voltage PD detector, calibration device of ultrasonic PD detector, calibration device of high frequency PD detector, calibration device of ultra high frequency PD detector.
-
product
IV Characteristics Measurement Device [
PECK2400-N
Easy-to-use measurement software supports IV measurement (software + source meter + connection cable) ● Compatible with Windows 10 ● RS-232C connection (PC is optional) ● Works with NI GPIB. ● Simultaneous use with IPCE PEC-S20 D type is possible. ● There is only one operation panel. done on one screen.
-
product
Differential And I/Q Device Measurements
S95089B
The S95089B combines source-phase control of multiple internal or external sources with frequency-offset mode, enabling simplified test of I/Q modulators/converters, differential mixers, and harmonics or amplifiers.
-
product
Modular Gravity Handler For Small Devices
Rasco SO2000
Modular designed gravity handler with various input and output possibilities. SO2000 can handle the smallest possible packages for gravity and provides a broad range of Sensor and MEMS applications.
-
product
PCI Resistor Card 4-Channel 1 Ohm To 63.7 Ohm
50-293-011
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
4 Port Devices
Four port devices can be realized by joining two 3 port devices via the appropriate ports. As system performance requirements become more demanding, new design approaches must be adopted. These include Faraday rotation devices and phase shift circulators. The bandwidth and isolation limitations of 3 port devices are overcome through a distributed architecture that enables more ferrite material to be incorporated into the transmission path, thereby achieving an increase in the biasing magnetic field. Phase shift circulators can be designed to handle higher RF power than 3-port devices.
-
product
PCI-8531, 1-Port, CANopen Interface Device
781060-01
The PCI‑8531 is a high-speed CANopen interface for developing applications with the NI‑Industrial Communications for CANopen driver. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation … applications. CANopen was designed for motion-oriented machine control networks, such as handling systems, but now it is used in a variety of products and applications, including medical equipment, off-road vehicles, maritime electronics, public transportation, and building automation. The PCI‑8531 can transmit or receive process data objects (PDOs) and service data objects (SDOs) according to CiA‑DS 301. It also features a batch SDO editor with EDS file integration and LSS services support for slave node configuration.
-
product
Stand Alone Test Device
The ENGMATEC Smart Contact Cell works with goods carriers that move above and below each other. This enables the test objects to be fed in and removed in parallel, which significantly reduces handling times.
-
product
DC High-Voltage Test Device
PGK 80
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR PGK 80. The portable, one-piece PGK 80 high-voltage test device for generating negative DC voltage up to 80 kV is primarily used for onsite testing of paper-insulated mass-impregnated cables in the medium-voltage network. The high voltage is generated through a high-voltage transformer with secondary voltage-multiplier. The internal operating frequency of 20 kHz enables the smallest of device dimensions.* Continuous adjustable output voltage* The voltage measurement is done directly at the high voltage output* Timer of 1-30 min* Sensitive current measurement for recording the smallest of insulation currents with 6-time range switch, decadal
-
product
Digital Multipurpose Easuring Device
MPG 96
A modern multipurpose measuring device to be built into a panel. With its design, it is intended for installation into all types of switchboards and other devices. It offers many functions and the option to save the data measured.
-
product
PCI-8517, 2-Port FlexRay Interface Device
780685-02
2-Port FlexRay Interface Device—The PCI‑8517 is designed for developing FlexRay applications. As part of the NI‑XNET platform, the PXI‑8517 works well in applications requiring real-time, high-speed manipulation of hundreds of FlexRay frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The PCI‑8517 contains two fully functional FlexRay interfaces, allowing an individual engine control unit (ECU) to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface.
-
product
Metrology Device
XPLOR 100
XPLOR 100 is a state of the art, fully automated metrology device designed for measurement and analysis of bubbles and inclusions for optical substrates in the Visible and NIR wave-bands.
-
product
Electronic Safe & Arm Devices
Excelitas Technologies specializes in the design, manufacture, and testing of MIL-STD-1316 compliant Electronic Safe and Arm Devices (ESAD), Electronic Safe, Arm and Fire Devices (ESAF), and Firing Modules (FM) for safe fuzing requirements of both legacy and next-generation missiles and munitions. Our dedicated staff of research and design experts use the latest advances in technology to design smaller, lighter, and more cost effective ESAFs and FMs to meet evolving requirements of newer more sophisticated weapon systems. Capabilities include a line of components and subsystems that have been qualified for hard target penetration environments and next-generation smaller-class munitions.
-
product
PXI Resistor Module 4-Channel 1R to 510R with SPDT
40-293-114
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Automated Multi-Edge Measurement Device
EdgeMasterX
The EdgeMasterX is a fully automated cutting edge measurement device for production integrated quality assurance of inserts, drills, mills and other round tools. Specifically, the EdgeMasterX enables automated multi-edge measurement of tools. In a single measurement run, a complete series of user defined measurements at multiple edge positions can be achieved. All results are traceable, repeatable, and in a high vertical resolution.
-
product
PXI 2.5W Programmable Resistor Module, 4-Channel, 1Ω to 470Ω
40-251-114
The 40-251-114 is a programmable resistor module with 4 channels which can be set between 1Ω and 470Ω with 2Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Programmable AC/DC Withstanding Volatge And Insulation Tester
RK-7122
Shenzhen Chuangxin Instruments Co., Ltd.
Programmable AC/DC withstanding volatge and insulation tester
-
product
Battery Pack Rotate Test Device
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Battery Pack Rotate Test Device Single storage cell safety testTest object: Battery storage pack or systemRotate the battery pack 360°around X axis with rotation speed of 6°/s; secondly rotate it 90°,180°,270°,360°,and remain for one hour after each move. Then stop and observe for 2 hours.Rotate the batter pack 360°around Y axis with rotation speed of 6°/s; secondly rotate it 90°,180°,270°,360°,and remain for one hour after each move. Then stop and observe for 2 hours.Accept standard: Battery pack or system has no electrolyte leakage, no rupture at case, no fire nor explosion. And remain the connection reliable, the structure intact, the insulation resistance value not less than 100 Omega /v.
-
product
IV Characteristics Measurement Device Software
Keithley 2400, 2401 and Keithley 2450
*Windows 10, Windows 11 (Compatible) RS-232C (Keithley 2400, 2401), USB (Keithley 2450)*NI GPIB can also be used (optional)*IPCE PEC-S02 can be used simultaneously. operation panel. *Everything from condition setting to measurement can be done on one screen.
-
product
Electrical Circuits Control Device
ZET 452
ZET 452 is an automated module for electrical circuits parameters control that is used for electrical circuits impedance and insulation resistance monitoring in automated mode. The monitoring is performed in accordance with the set participation and without participation of an operator. ZET 452 allows to reduce the time necessary for verification procedure more than in 20 times if compared with the standard measurement instruments normally used for these purposes.
-
product
Differential And I/Q Device Measurements
S93089B
The S93089B combines source-phase control of multiple internal or external sources with frequency-offset mode, enabling simplified test of I/Q modulators/converters, differential mixers, and harmonics or amplifiers
-
product
High-Precision Programmable DC Power Supply
MPS-3600H Series
MPS-3600 HSeries is a new generation of high-precision programmable DC power supply. This series of products is equipped with a standard communication interface, which has both desktop and system characteristics. It can be arbitrarily matched with other instruments and integrated into a special function test system to complete the measurement requirements in different occasions.
-
product
Programmable Setpoint Relay Protection Relay, Trip Relay
CRD-005 and CRD-020
CRD-020 Programmable ac current set-point relay setting for threshold levels, over and under-currentoperationbullet CRD-005 Programmable dc voltage and mA set-point relay setting for threshold levels, over and under-voltage operationbullet CRD-005 internal DIP-switches allow for either 0-1mAdc or 0-10Vdc operation, and may be set for under-alarm or over-alarm relay operationbullet CRD-020 internal DIP-switch allow configuration of the ac current range to either 0-5A, 0-10A, 0-15A or 0-20A and the relay mode for under-current or over-current operationbullet Lid mounted two digit numerical push button switch calibrated as percent of full scale with a threshold range of 1-99%bullet Red LED lamp lights to indicate when the threshold level has been tripped
-
product
Programmable Digital Panel Meters
RS485
Kusam Electrical Industries Limited
• Manages sending and receiving signal of multiple Modbus RTU instruments.• Programmable address for reading data• Data form: Unsigned Int / Signed Int• Max.Baud rate: 38400• Programmable address:1 ~ 255• With alarm setting and analog output
