Device Programmers
Program non-volatile memories, logic devices, microprocessors and other electrically-programmable devices.
See Also: Programmers
-
product
PCI Resistor Card 2-Channel 2 Ohm To 65.5k Ohm
50-293-033
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Radiation Survey Device
DRG-T
The DRG-T radiation survey device is designed for use in special-purpose vehicles for continuous control and measurement of exposure dose rate (EDR) of gamma and X-ray radiation, as well as for providing audio and visual alarm of its dangerous levels and for issuing commands to start the actuators of protection equipment.
-
product
PXI 5W Programmable Resistor Module, 1-Channel, 2.5Ω to 201kΩ
40-252-041
The 40-252-041 is a programmable resistor module with 1 channel which can be set between 2.5Ω and 201kΩ with 0.25Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PXI/PXIe 15W Programmable Resistor Module
40-254-032
The 40-254-032 (PXI) and 42-254-032 (PXIe) are programmable resistor modules with 1 channel which can be set between 2Ω and 26.7kΩ with 0.5Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
product
Passive Tapping Device
DSL Phantom™
DSL Phantom™ is a unique passive tapping device for Lawful Interception (LI) of ADSL lines. The device records and stores broadband digital information, offering unique advantages to Law Enforcement Authorities (LEAs) looking to capture data between the target and the service provider premises.
-
product
Programmable Power Modules
Series MST
MST power modules are a group of programmable power supplies that are compatible with Kepco¹s single address, multiple instrument serial control bus. The MST provide precision interactive control in the 200 Watt power class. The housings for MST, either RA 55 or CA400, each contain a slot to accommodate an IEEE 488.2 adapter. If not used, an additional MST power module may be plugged into that slot.
-
product
Controllable, Programmable Clocked AC Source
EAC-AFV
*Output from 15kVA to 2000kVA*Output voltages 0VAC to 700VAC / 1000VDC per phase*Maximum currents up to 2000A per phase*Simulation of 1- and 3-phase networks (worldwide)*Variable frequency of up to 2000Hz, sine, square, triangle*Indication via graphic display
-
product
High-Voltage Test Device
PGK 260 HB
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR PGK HB. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit. *Testing of medium- and high-voltage cables * DC voltage testing of up to 260 kV output voltage with positive or negative polarity * AC voltage testing - up to 190 kV for switchgear, busbars and insulating elements * Easy-to-maintain 2-piece design
-
product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 63.7 Ohm
50-294-011
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
GPIB-RS232, Instrument Control Device
779732-10
The GPIB‑RS232 is an IEEE 488 controller device for computers with an RS232 port. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS232 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS232 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488 and RS232 standards, as well as interpret and execute high-level commands from the serial port, including RS232‑to‑GPIB and GPIB‑to‑RS232 protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
Samples Moving Device
Wewon Environmental Chambers Co, Ltd.
Wewon Environmental Chambers Co., Ltd. helped aircraft glass manufacturing company design a kind of glass samples moving device. The aircraft glass sampels are stored on the movable device, and the aircraft glass is smoothly sent into the test room through the movement of the roller. This type glass samples moving device designed by Wewon Tech has a total height of 2100mm. After measurement, We have found that the shell width of the samples moving device is 1300mm and the depth is 1550mm.https://www.wewontech.com/samples-moving-device/
-
product
Power Switching Devices
Watlow Electric Manufacturing Company
Watlow solid state power switching devices complement the rapid switching required by PID temperature controllers and help deliver optimum system performance and service life. They are available in 1-phase and 3-phase/2-leg and 3-leg configurations, feature touch-safe terminations, input indicators, zero-cross, random or phase-angle fire options, ratings from 18 to 1,000 amperes and agency approvals including CE and UL® 508. Various configurations offer short circuit current ratings (SCCR) of 200,000 amperes, extensive system and heater diagnostic capabilities, heater bake out, integrated heat sinks, on-board fuses, RoHS compliance and serial communications.
-
product
Recorder Carrier Device
RCD
The RCD is a carrier signal demodulator for SCADA and Fault Data Recording. the RCD demodulates the carrier to indicate the presence of a relative level of a singal
-
product
High-accuracy Dual-channel Programmable Battery Simulator
N8352 Series
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
N8352 series is specially designed for the R&D and testing of portable, battery-operated products , such as Bluetooth headsets, mobile, AR/VR smart terminals, electrical tools, etc. The current flows in both directions and can be used as either a power supply or a load. N8352 is easy for operation with touch screen and UI design. The output features are comparable to actual batteries, with fast dynamic response, no overshoot in voltage rise and fall, and stable waveform. The resolution is up to nA level, which can test the loop static power consumption, etc. N8352 can be widely used in the area of consumer electronics testing.
-
product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 65.5k Ohm - SPST
40-294-133
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Visual Visual Inspection Device
IP-3000
Our visual visual inspection device Inspection Pro IP-3000 is an inspection device that quickly and accurately inspects the mounting board, which is constantly evolving, and judge whether it is good or bad without omission.
-
product
Single Light Beam Safety Devices
Leuze electronic GmbH + Co. KG
Single light beam safety devices can be integrated flexibly into machine concepts – particularly in constrained spaces or where no flat mounting surfaces exist. They are used for point of operation and access guarding as well as for collision avoidance. The safety sensors are available as type 2 and type 4 devices with external monitoring as well as self-monitoring type 4 devices.
-
product
Ethernet Multifunction DAQ Device
T4
USB or Ethernet multifunction DAQ device with up to 12 analog inputs or 16 digital I/O, 2 analog outputs (10-bit), and multiple digital counters/timers. For more information on the T4 take a look at the T4 product announcement news post.
-
product
Programmable Electrical Rule Checking tool
Calibre PERC
Calibre® PERC™, Mentor Graphics'' newest reliability verification solution is designed to address your advanced circuit verification needs for electrostatic discharge (ESD), electrical overstress (EOS), signals crossing multiple power domains, advanced ERC and other reliability concerns.
-
product
Electricity Metering Device- Residential
ES-10B
Designed for the residential smart meter rollout in Great Britain, this 4 terminal single phase electricity meter is the second generation version within our SMETS2 compliant solution.Taking learnings from the first generation meter, the ES-10B is a more refined SMETS2 compliant electricity meter with 100A main disconnect relay, dedicated secure microcontroller and with multiple interfaces including Zigbee and DLMS.
-
product
Power Devices & Power Conversion
CAES has a legacy of supplying high-performance power and power conversion products to the aerospace market, providing ground power to fighter jets and other aircraft and assisting with applications such as aircraft engine starting.
-
product
PXIe-4112, 2-Channel, 60 V, 1 A PXI Programmable Power Supply
782857-01
The PXIe‑4112 is a programmable DC power supply with isolated outputs. It helps simplify the task of designing automated test systems for a wide range of applications—from aerospace and defense to automotive and component test—by eliminating the need to mix multiple instrumentation form factors in a given test rack. It also has standard output disconnect functionality that allows isolation from the device under test (DUT) when not in use, and remote sense to correct for losses in system wiring.
-
product
Inspects MEMS and Wafer Level Devices
NorCom 2020-WL
The NorCom 2020-WL is specifically designed for wafer-level inspection and leak tests up to 1000 devices per cycle. The system can inspect up to an 8” wafer on or off a saw frame. It is designed to test MEMS and other wafer level devices that have a cavity.
-
product
Power Semiconductor Device
IGBT/SIC
Hitachi High Voltage IGBTs have been corresponding to a wide range of applications such as railway applications and various power conveters, leading companies for domestic and overseas adopt them, since they were adopted as a railway application in 1992. Will continue to contribute to the developing energy society by pursuing more easy-to-use, high-performance and high -quality products with leading-edge research and development.
-
product
VXI Programmable Video Generator & Analyzer
Enhanced VXI Programmable Video Generator and AnalyzerComposite, Raster, Stroke, HDMI, DVI, SDI, Embedded Display Port, and Image Capture and Analysis Options
-
product
PCI Precision Resistor Card 3-Channel, 2.5Ω To 102kΩ
50-297-140
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
High Throughput Device Server
DS-600
The Silex DS-600 is designed to easily connect and share USB 3.0 and 2.0 devices over a network. Printers, Scanners, Disk Drives, Cameras, Card Readers, or virtually any other USB device can be now be enabled with network capability. It allows flexibility to place the USB device anywhere on the network instead of needing to be attached directly to the computer, and multiple users can access the USB device.
-
product
Device Networking
Offers complete control of how and when the application can discover, connect, disconnect, and get status from the USB device across the network.By integrating the SDK, you can create your own user interface and make it work seamlessly with your application.The SDK supports searching device servers on the network.Supports getting information and status from the USB device server.
-
product
Programmable RF Attenuators
The AD-USB R3 is AdauraTech’s latest design in the AD-USB series of programmable RF attenuators. Combining all the best features of the previous models, the R3 is the new series flag ship. With a completely custom machine aluminum enclosure, the R3 boasts 95dB of attenuation. The addition of Ethernet allows EASY implementation into the most modern of test setups by allowing network control via HTTP web interface or direct Telnet while the USB port powers the device and allows for serial communication.
-
product
RF Device Tester
RF ITS
Sterner's automated test management system, combined with integrated RF technology modules, provides full functionality, including: Apply power to the device under test (DUT). Read and write blocks of data to set up and validate product EEPROM using a hard-wired communications interface. Scan transmitting devices or traveller barcodes and write the information to the DUT (the "sign-up process"). Inject an RF signal of known frequency and power level to test receiver sensitivity.
