Insulation Testers
-
Product
System and Collection Tester
SysColl
-
For certification in many markets, performance of the complete factory made system (for example thermosiphon systems) plays an equally important role as collector performance. Our SysColl test stand is a combined test facility for performance testing of both solar collectors and solar thermal systems. This allows you to take advantage of a flexible two in one test solution.
-
Product
Relay Tester Kit
7612A
-
Peaceful Thriving Enterprise Co Ltd
This is the device to test 3 popular vehicle relays. The testing result will be displayed by LED indication. Technician is able to use the device to figure out the condition of the relay, and so speculating the problem in the vehicle. Use the relay adapter to plug into the relay tester, suitable to connection multiple styles relay.
-
Product
Load Cell Tester
LCT-Ultimate
-
Industrial Measurement Systems Ltd.
This most advanced Load Cell Tester model LCT-Ultimate is a stand-alone hand-held device that was especially designed for full trouble shooting of strain-gage based load cells. The LCT-Ultimate can check all common types of standard load cells that are available on the market:
-
Product
Outdoor Exposure Tester
OET
-
A comprehensive analysis of PV modules includes many different parameters. Determining the normal module operating temperature (NMOT), incidence angle effects and comparing soiling effects on different modules up to the initial degradation of PV modules are all parameters that can be analyzed with our outdoor exposure tester. The tester comes with up to twelve electronic loads installed in a 19" rack. The loads have two main functions: maximum power point tracking (MPPT) and IV curve tracing. For the advanced analysis, it is possible to change between these two modes within one test. In the normal operation mode, the electronic load keeps the module under MPP and each predefined interval an IV curve is traced. The entire tester comes with all necessary sensors such as temperature sensor, which can be attached to the module to determine the NMOT temperature like defined in IEC 61215 (MQT 05) and IEC 61853-2. The irradiation sensor is also included. In combination with our tracking system P2, it is also possible to determine incident angle effects of the PV module. It is also possible to connect other irradiation sensors for diffuse and direct irradiation, which helps to understand the behavior of the module in different irradiation conditions. An optional albedo meter is a powerful tool for the analysis of bifacial modules. The entire graphical user interface is web based and offers the possibility to access the system from the all computers in the network.
-
Product
Pitot Static Tester
ADSE 550
-
The ADSE 550 pitot static tester, housed in a plastic carrying case, is a portable, self contained field tester designed to test aircraft pilot ans static systems for leaks as well as the operation and calibration of airspeed, altimeter, engine pressure ratio, manifold pressure indicators, and other vacuum or low pressure units. The tester consists of a hand-operated vacuum pump, a hand-operated pressure pump vacuum and pressure gauges, 5 control valves, an altimeter and an airspeed indicator. The package accessories include two 25-foot hoses.
-
Product
Vacuum Switch Tester
-
Weshine Electric Manufacturing Co., Ltd
1. The instrument has an automatic measurement function.2. The instrument has a perfect back-EMF protection function.3. The instrument uses a 5-inch 65K color LCD touch screen, which is easy to operate.
-
Product
HIGH-VOLTAGE TESTERS 0-10KVac UP TO 0-40kVac
AV-100VA-5V
-
HIGH-VOLTAGE TESTERS 0-10KVac UP TO 0-40kVac
-
Product
Loop Tack Tester
-
Loop Tack Tester is applicable to measure the tack property of adhesive tapes, pressure-sensitive adhesives (PSA), and adhesive materials according to ASTM D6195.
-
Product
Drop Tester
AccuDrop 160A
-
Model AD-160A is 1 of 3 models in the ACCUDROPTM Series. It helps determine the ruggedness of packagesand the effectiveness of their interior cushioning when exposed to impact during material handling. Theeffects of dropping are easily duplicated in your laboratory using the controlled and precise flat, corner, andedge drop tests.
-
-
Product
Countermeasures Dispenser Testers (CDT)
-
The nation’s Air Force, Army, Navy, Marine Corps, and key government agencies all depend on countermeasure dispensing systems – including the AN/ALE-47 and others – aboard their aircraft for self-protection against missile attacks and other airborne munitions. Especially when operating in contested areas, a properly-functioning countermeasure dispensing system can make all the difference to the success of a mission. That’s ample reason for aviation maintenance and flight prep crews to prefer the unmatched reliability of BAE Systems Rokar Countermeasure Dispenser Testers (CDT) for keeping their countermeasure dispensing systems performing effectively and safely.
-
Product
Smart SMD Testers
-
Precision Mastech Enterprises Co.
Compact, battery-operated, tweezer-like electronic tools designed for quickly measuring, identifying, and testing Surface Mount Device (SMD) components such as resistors, capacitors, and diodes.
-
Product
6/12/24/36V Conductance Battery Tester
MBT300
-
Tests 6/12/24V lead acid batteries individually or in parallel and series battery packs. Displays battery or battery pack condition as % available capacity, rated capacity (CCAs), state of charge voltage, and good or replace status. Tests 6/12/24/36V starter and charging systems including starter draw, alternator and regulator output (loaded/unloaded), and diode ripple.
-
Product
Ozone Concentration Tester
OCT-3 PRO
-
Do you want to know if you can safely share a room with clients that has just been ozonated? Or maybe you want to compare the efficiency of ozonators? The OCT-3 PRO tester is the solution for you.
-
Product
Entry Level Loss Tester
Model：OLT-20
-
OLT-20 Optical Loss Tester integrates laser source module and power meter module in one set, which can perform power testing and link loss testing in optic fiber network conveniently. The typical applications include fiber identification, attenuation and loss measurement, continuity verification and fiber link transmission quality evaluation for installation, routine inspection and daily maintenance of MAN, WAN and CATV systems as well as for lab test and research work.
-
Product
Needle Flame Combustion Tester
-
Shanghai Dean Electrical Co., Ltd
The touch screen control needle flame combustion tester is developed according to the requirements of the needle flame combustion test in the standard
-
Product
Welding Resistance Tester
WRT
-
The Welding Resistance Tester is used in battery assembly lines to detect defective intercell connections. It is equipped with a 5-channel test head for car and truck batteries. It features 1-20 O DC resistance ranges and a multi-line LC display for OCV, CCV, and DCR measurements for 5 intercell connections.
-
Product
SF6 Density Meter Tester
JHMD-1
-
Xiamen Jiahua Electrical Technology Co.,Ltd
JHMD-1 is a smart tester. By using high accuracy core units, pressure sensor, A/D, D/A transducer, 32 bit ARM MCU and TI company’s high speed signal chip, it can automatically calibrate the density relay, measure pressure at signal activity temperature, convert pressure from any temperature to 20℃ standard pressure, print test data and save for review. It identifies the fault during the test. The whole procedure is under automatically operation, JHMD-1 is a high accurate, high stable, reliable tester.
-
Product
AC Hipot Tester
-
KV Hipot Power Test Equipment Co.,Ltd
The Hipot tester is a nondestructive test which is a effective way to determine the insulation strength for electric equipment.
-
Product
Electronic Product Testers
-
Infinity Machine International Inc.
Electronic Product Testers by Infinity Machine International Inc. - for applications such as connectors insert and extract testing machine, touch screen torsion, abrupt pull tester for power wire and headphone cable, double station electronic product cable tester, cord flexing rotary bending fatigue tester, button click electronic product tester simulation, and more.
-
Product
UL94 Combustion Chamber, IE60695vFlammability Tester
CX-S16
-
Shenzhen Chuangxin Instruments Co., Ltd.
Horizontal Vertical Flame Tester is a comprehensive test instrument whick strickly designed according to Standard IEC60695, GB5169, UL94 and can meet the relative standard's requirements. It's mainly used to test the flammability of plastic and other nonmetalloid parts specimen to evaluate fire hazardous degree of accidental burning caused by the material.
-
Product
A C DIELECTRIC STRENGTH TESTERS ( HIPOTS )
AVC-25V
-
A C DIELECTRIC STRENGTH TESTERS ( HIPOTS ). Two high-voltage leads, one c/w a clip and one c/w a retractable probe. Each is 2 meters (6 ft) long.
-
Product
Dielectric Insulation Analyzer
DIRANA
-
DIRANA uses dielectric frequency response (DFR) analysis in order to determine the condition of high-voltage insulation systems such as those in power transformers, bushings, cables and generators.
-
Product
Traction Battery Drop Tester
-
Guangdong Bell Experiment Equipment Co.,Ltd
Traction Battery Drop Tester Relevant standards requirementsSingle Storage Cell Safety TestDropt testing steps：Charge the single storage cellaccording to 6.1.3Drop the positive negative terminals of the cellfrom the height of 1.5m to the concrete floor；Observe for 1hBattery Module Safety TestCharge the battery module according to the standard 6.1.4Drop the positive negative terminals of the battery from the height of 1.2m to the concrete floorObserve for 1h
-
Product
LAN Tester
TVR10/10/100
-
Triplett Test Equipment & Tools
TVR10/100/1000 LAN Tester is comprised of a "Main unit" and a "Remote Probe". The Main unit performs the bulk of the tests, such as determining the LAN device type (is it a hub/switch or PC?), the LAN speed and duplex (10, 100, 1000 MB/s, half or full duplex) and whether PoE (Power over Ethernet) is present without the need of the Remote Probe. The Remote Probe adds the ability to trace cable locations (by audibly tracing tones placed on the cable by the Main Unit) and to test the wiring of the cable (by decoding and displaying wiring information placed on the cable by the Main Unit).
-
Product
Signature Model Surge Testers
SP
-
Surge / DC Hi-Pot testing capabilities. Tektronix TDS1002, 1 Billion Samples/sec, real time, programmable, storage oscilloscope plus a DC Hi-Pot Tester. DC Hi-Pot testing with dual LED panel meters that display direct read out of current and voltage, with overcurrent safety trip. This dual tester combo is still capable of testing 3 phase motors with or without rotors.
-
Product
Battery Tester
CS-3001
-
The CS-3001 test system records all block voltages, total voltage and current during a discharge test. The modular design makes it easy to connect most of all battery installations, starting from a single block and ending up with 960 block voltages. Up to four parallel strings can be tested. All measuring modules are electrically isolated (600VDC CAT III, 5000VAC test voltage).
-
Product
Rubbing Fastness Tester
-
Sataton Instruments Technology CO., Ltd
Rubbing fastness tester/Crockmeter is professional designed for determining the resistance of the color of textiles of all kinds, including textile floor coverings and other pile fabrics, to rubbing off and staining other materials in dry or wet conditions. Rubbing fastness tester can also be used to determine the color fastness to rubbing of ink, printing, dyeing, etc. There are two modes of manual and automatic for different requirements.
-
Product
Portable Hardness Tester
PHT-1700
-
Loaded with features, this economically priced hardness tester is capable of measuring the surface hardness of a broad variety of metals on flat and round surfaces. This instrument comes complete with the universal D impact device, calibrated test block and rugged carry case.
-
Product
Torque Tester
DIS-IPS series (20CL/5C)
-
For managing various torque wrenches, torque drivers, and automatic/semi-automatic machines. The highly compact detector is ideal for automated line measurements. Five channels of pass/fail judgment conditions can be saved, and settings can be made simply by switching channels even if the tightening conditions change. Efficient measurement is possible without unwinding work by "OW joint ".
