Filter Results By:
Products
Applications
Manufacturers
-
product
Sand & Dust Test
This test method is divided into two procedures. The small particle procedure, using fine dust is performed to ascertain the ability of equipment to resist the effects of fine particles which may penetrate into cracks, crevices, bearings, and joints. The blowing sand test, using coarse particles, is performed to determine whether equipment can be stored and operated under blowing sand conditions without experiencing degradation of its performance, effectiveness, reliability, and maintainability due to the abrasion or clogging effect of large, sharp-edged particles.
-
product
Material Testing
*Abrasion Testing*Adhesion Testing*Brittleness Temp.*Bursting Strength*Coating Testing*Coefficient of Friction*Compression Testing*Compression Set*Dart Drop Testing*Density Determination*Fatigue Testing*Fiberboard Testing*Flammability Testing*Flexural Testing*Foam Testing*Hardness Testing*Heat Deflection*Hydrostatic Testing*Impact Testing*Life Cycle Testing*Melt Index Testing*Plastic Testing*Ply Separation*Resin Content*Rubber Testing*Shear Strength Testing*Stress Crack Testing*Tear Testing*Temperature Testing*Tensile/Elongation*UV Exposure*Water Absorption*Wood Testing
-
product
Oscillatory / Wyzenbeek Abrasion Tester
TF212
TESTEX Testing Equipment Systems Ltd.
Wyzenbeek Abrasion Tester. Modern ergonomic design to determine the abrasion resistance of fabrics when rubbed against a standard abrasive or a wire mesh screen with a backward and forward motion over a curved surface. Wyzenbeek abrasion tester applies to automotive and furniture industry fabric manufacturers working to US Standards Motor driven with 4 abrasion heads and electronic digital counter to control the number of cycles.
-
product
Film Application & Test Charts
For numerous products, such as paint, ink, varnishes, glue and cosmetics, the reliability of many laboratory tests is directly related to the quality and consistency of the samples. Any measurements made on coatings for the purpose of describing their physical properties (drying time, elasticity, abrasion, gloss, colour, shade, etc.) are made on the basis of uniform and comparable samples with precisely controlled thickness.
-
product
IEC61588 And IEC60065 Mandrel Test Apparatus
CX-M01
Shenzhen Chuangxin Instruments Co., Ltd.
IEC61588 and IEC60065 Mandrel Test Apparatus is designed and manufactured in accordance with the standard requirements of IEC61558 and IEC60065. The IEC61588 and IEC60065 Mandrel Test Apparatus is used for the insulating thin layer of the power transformer and supply unit as well as the similar products to do the spindle test, mechanical strength test and abrasion test.
-
product
Physical Test Equipment
When assessing a coating for suitability for a particular application the testing of the physical properties such as bendability, impact resistance, hardness, washability and abrasion resistance are all required to provide information for decision making. Testing of the pigments using fineness of grind gauges, determining the specific gravity of the coating using density cups, measuring the viscosity using viscosity cups or rotational viscometers and assessing the drying time all provide information for the coating technical data sheets.
-
product
Rope Testers
The LMA Signal measures loss of metallic cross-sectional area (LMA) caused by corrosion, abrasion, etc. The LMA Signal is quantitative and can be calibrated. (Typically, a rope must be retired when the LMA exceeds 10%).The WRR Signal measures wire rope roughness (WRR). WRR is defined as the aggregate surface roughness of all wires in a rope. WRR is typically caused by and indicates internal and external corrosion pitting, broken wires and clusters of broken wires. The WRR signal is quantitative, and it is calibrated together with the LMA Signal.The LF Signal can indicate localized flaws (LF), for example, broken wires, corrosion pitting, etc. Because it is only qualitative - and cannot be calibrated - it is of limited value for assessing rope deterioration and for making rope retirement decisions.
-
product
Textile Testing Equipment
Dongguan Kejian Instrument Co., Ltd.
Used for testing the performance of the wearing resistance,abrasion, appearance change (pilling degree/class) of the textiles and membrane materials.
-
product
Sand And Dust Test Chambers
Dongguan Amade Instruments Technology Co., Ltd
Sand and dust test chamber is also referred as dust-proof chamber, which is able to simulate the sand storm by putting the test piece in the chamber to judge the damage of sand-and-dust weather to products. Equipment is mainly applicable to determination of sealing performance of product shells based on the IPX5 and IPX6 degrees. Testing machine features a flow of air carrying dust in a vertical circulation, resulting in cycle use of sand during the test. Sand and dust testing has great significance to master the specimen’s performance to defend the penetration of dust particles, to withstand the abrasion of sands.
-
product
DIN Abrasion Tester
UI-FT24
DIN Abrasion Tester – DIN Abrader(Abraser) is a Rotary Drum Abrasion Tester of rubber testing instruments to test abrasion resistance of rubber, shoe sole. DIN abrasion test method meets ISO 4649, DIN 53516, ASTM D5963, SATRA TM174, and other abrasion resistance test method.
-
product
DIN Abrasion Tester
TF215
TESTEX Testing Equipment Systems Ltd.
DIN Abrasion Tester, to determine abrasion of flexible materials, such as rubber, tires, transmission belts, soles, leather etc. The abrasion tester is provided with a wide testing area to meet the most requests. Additional balance is required.
-
-
product
Abrasion Tester
rHT SeriesHB SeriesHT Series
Abrasion tester checks the abrasion of solid materials. such as metals, composites, ceramics and more.The test is performed on worn materials such as tires, shoes, belt and more.* Worn out condition* The loss of the weight* The loss of the physical volume* The thickness that been worn out, etc* Use NBS standard gum to ratio the endurance characteristic of abrasion for this material.
-
product
Martindale Abrasion Tester
UI-FT19
Martindale Abrasion Tester is used to test pilling & abrasion resistance of textile fabric, leather and other materials by rub sample in all directions (a Lissajous figure) in wet or dry conditions.
-
product
IEC60558 Insulation Material Layer Abrasion Resistant Test Device
CX-J16
Shenzhen Chuangxin Instruments Co., Ltd.
This test is conforms to IEC60558-1 Fig6 and IEC60065 Fig14--16.The test shall be performed by fixing the specimens of thin sheets on a mandrel made of nickel plated steel or brass with smooth surface finish.
-
product
Universal Wear Tester
TESTEX Testing Equipment Systems Ltd.
Universal Wear Tester, to determine the wear and abrasion resistance of fabric used in clothing, footwear and industrials. This Wear Testing Machine complies with ASTM D3514/D3885/D3886, AATCC 119/120, FTMS 191/5300/5302, etc.
-
product
Shoelace Abrasion Tester
UI-FT39
Shoelace Abrasion Tester is used to determine shoe lace to lace abrasion resistance to repeated rubbing.
-
product
Custom Cable Assemblies
AMETEK Power Instruments has designed and manufactured electrical, thermocouple, and fiber optic harness assemblies for more than sixty years. We have the experience and capability to produce rigid and flexible harness assemblies for virtually any application, whether it is a missile ignition assembly, aircraft actuator assembly or a thermocouple harness for an industrial gas turbine. AMETEK Cable & Harness Products boast superior reliability, high temperature operation, numerous braiding options for abrasion resistance and EMI shielding, waterproof or environmentally sealed, and custom molding. For more information, please contact us.
-
product
Martindale Abrasion and Pilling Tester
Sataton Instruments Technology CO., Ltd
By providing a defined load, a translational movement tracing a Lissajous figure and abrasive medium, martindale abrasion tester is professional designed for determining of the abrasion resistance of fabrics including specimen breakdown, mass loss and appearance change. The tester can also use to determine the resistance to pilling and surface change of textile fabrics. With accessories, the tester is to determine abrasion resistance of lining and insock for personal protective footwear. It is widely used to evaluate the properties of clothes fabrics, coating materials, wool fabrics, nonwovens and other special materials for protective equipment.
-
product
DIN Abrasion Tester
Sataton Instruments Technology CO., Ltd
DIN abrasion tester basing on the rotating cylindrical drum is to determine the volume loss and abrasion resistance index due to the abrasion action of rubbing a specimen over a specified abrasive. It is the recommended testing machine to evaluate for abrasion resistance of rubber, vulcanized or thermoplastic materials. The tester includes a laterally movable specimen holder and a rotatable cylinder with abrasive sheet fixed can provide two testing methods, non-rotatable specimen test and rotating test piece.
-
product
NBS Abrasion Tester
UI-FT40
NBS Abrasion Tester is used to test rubber abrasion resistance and to know material nbs abrasion index. NBS abrasion test is suitable for vulcanized rubber used for soles and heels of footwear. Unuo NBS Rubber Abrasion Tester is designed and applicable according to ASTM D1630. Here for More Abrasion Tester.
-
product
Washability & Abrasion
Improved mechanical resistance to wear is a key requirement of a wide range of products. From coatings to clothing, leather to upholstery, keypads to plastic toys, a product’s ability to resist wear is an important characteristic. There are testing methods relating to the ‘abrasion by friction’ concept. Others are based on the projection of abrasive particles on to the test specimen. These techniques provide valuable information about materials and processes.
-
product
Flow Meter
Ultra Mag
The Ultra Mag is an advanced, leading-edge electromagnetic flow meter. It?s field-proven for the specific needs of the water & wastewater industries. The unit?s unique NSF-approved UltraLiner provides superior electrical insulation as well as excellent protection against corrosion and abrasion.
-
product
Scott Type Crease-Flex Abrasion Tester
TESTEX Testing Equipment Systems Ltd.
Scott Type Crease-Flex Abrasion Tester, to determine the crease-flex abrasion resistance of leather, rubber cloth etc. Scott Type Crease-Flex Abrasion Tester complies with JIS-K6404-6, L1096, JASO, etc.
-
-
product
Wyzenbeek Abrasion Tester
TESTEX Testing Equipment Systems Ltd.
Wyzenbeek Abrasion Tester，to determine the abrasion resistance of fabrics when rubbed against a standard abradent or a wire mesh screen with a backward and forward motion over a curved surface. Wyzenbeek Machine complies with ASTM D4157, etc. Please contact us for more information about Wyzenbeek methods.
-
product
Martindale Abrasion Tester
SG-P02M
This machine is ideal for determining the abrasion resistance of upper, lining, socking, and similar types of shoe materials, particularly those made of fabric. The specimens are capably tested for four bieces or six pieces(option) per time and are rubbed over the abrasive in all directions in a complex, repetitive pattern(a lissajous figure) and, at the same time, the holer totates.
-
product
Martindale Abrasion Pilling Tester
TESTEX Testing Equipment Systems Ltd.
Martindale Abrasion Tester, to determine the abrasion and pilling resistance of all kinds of textile structures. Martindale Test Equipment complies with EN ISO 12945-2/12947-1, ISO 20344, ASTM 4966/4970, etc. Martindale Fabric Abrasion Tester will meet your needs when you do Martindale rub test. Please contact us for more information about Martindale Machine or Martindale pilling test methods.
-
product
Abrasion Testing Machines
Infinity Machine International Inc.
Abrasion Testing Machines by Infinity Machine International Inc. - for application such as mobile phone coating abrasion testing, stainless steel friction tester, print ink abrasion testing, shoe lace abrasion testing, rubber abrasion testing, dyeing rubbing fastness friction test for decolorization, textile fabric abrasion testing, and more.
-
product
Harness Design and Manufacture
When designing an underwater cable harness, there are some factors which need to be considered, and we have produced the following list as a guide for customer information:Component considerations:- Electrical requirements- Mechanical considerations- Quality requirements- Reliability- Design redundancy (contact count)- Connector selection (type and form)- Locking requirements- Backpotting requirements- Waterblocking in moldings- Cable specification- Cable jacket material and compatibility with elastomers- Abrasion resistance- Stiffness profile at termination- Connector format (straight or right angle)- Molding format (straight or at an angle)- Clearance allowance for molding and cable routing- Elastomer compatibility (eg oil filled units)- Metalwork selection re: corrosion and cathodic delamination- Surface finish for metalwork as appropriateOperational considerations:- Operating depth profile (not just max. depth)- Tensile loads- Torsional loads- Bending loads- Bend control requirements (to limit bending at termination)- Deployment and recovery loads- Dynamic loading-Flow turbulence effects.
