6U PXI Chassis
See Also: PXI Chassis, 3U PXI Chassis, Portable PXI Chassis
-
Product
PXI Isolated Millivolt Thermocouple Simulator - 8 Channel
41-761-004
-
The use of two wire outputs and isolation from ground ensures that the 41-761 can be used to accurately simulate low voltages even in the presence of common mode voltages in the system. Each Vcold connection is independent permitting the 41-761 to be connected to multiple cold junctions.
-
Product
PXI 4 Slot BRIC 116x6 2A 1-Pole Matrix
40-596-002
-
The 40-596 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 150VDC/100VAC. The 40-596 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI Breadboard Module, 1-Slot, 78-Pin D-Type
40-220A-401
-
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
Product
PXI 8x2 RF Matrix 1.5GHz 50 SMB
40-750-511
-
The 40-750-511 is an 8x2 RF Matrix Module suitable for switching frequencies up to 1000MHz. It has a 50Ω characteristic impedance with front panel mounted SMB coaxial connectors. The matrix intended for the easy construction of high performance bidirectional switching systems.
-
Product
PXI Precision Resistor Module 9-Channel, 1.5 to 6.97k
40-297-024
-
This 9-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
6U Form Factor PMC/PrPMC Carrier-VMEbus
i4400
-
The i4400 is a low-cost 6U form factor PMC / PrPMC carrier for the VMEbus and forms the basis of a flexible I/O system. It offers the user a means of integrating two single PMC modules or one double PMC module in a VMEbus system. The current version of the i4400 supports PMC modules and also supports Processor PMC modules on one PMC-site. The VME-to-PCI bridge is implemented in an FPGA for flexible VME-to-PCI mapping and to allow future updates and upgrades.
-
Product
PXI 8-Slot BRIC Matrix, 20x32 1-Pole (4 sub-cards)
40-562B-121-20X32
-
The 40-562B-121-20X32 is a high density BRIC8 matrix module with a size of 20x32 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-241-HI
-
The 40-230-241-HI (PXI) and 42-230-241-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4Ω and 102kΩ with 0.25Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI 4-Slot BRIC Matrix, 55x16 2-Pole (5 Sub-cards)
40-562B-022-55X16
-
The 40-562B-022-55X16 is a high density BRIC4 matrix module with a size of 55x16 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 8 Slot BRIC 270x8 1-Pole (9 sub-cards)
40-561A-121-270X8
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
8-Slot BRIC, 384x8, 1 Pole, PXI Matrix (6 Sub-cards)
40-559-801-384x8
-
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI 8-slot BRIC Matrix, 320x16, 1 pole (10 Sub-cards)
40-558-801-320x16
-
The 40-558-801-320x16 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
Single 16x16 1-Pole High-Density PXI Matrix Module
40-520-001
-
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PXI Automotive Ethernet Interface Module
-
The PXI Automotive Ethernet Interface Module communicates with Automotive Ethernet so that you can use the NI‑XNET driver or standard networking drivers to develop applications that require Automotive Ethernet to test and validate automotive electronic control units (ECUs). It provides up to four independent endpoints or up to two network terminal access points (TAPs). With onboard hardware timestamping and the ability to act as 802.1AS masters or slaves, the PXI Automotive Ethernet Interface Module can synchronize with an external network as well as the rest of a PXI system.
-
Product
PXI 8-slot BRIC Multiplexer, 4-Channel, 40-Pole (3 Sub-cards)
40-570A-211
-
The 40-570A-211 is a 4-channel, 40-pole High-Density Multiplexer and is part of our BRIC family. The 40-570A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
Product
PXI 10 Banks of 16 Channel 1 Pole MUX
40-615-022-10/16/1
-
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration. Connections are made via a front panel 200-pin connector.
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 127 Ohm
40-294-012
-
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI 12-Slot BRIC Matrix, 352x8 1-Pole (16 sub-cards)
40-562B-321-352X8
-
The 40-562B-321-352X8 is a high density BRIC12 matrix module with a size of 352x8 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI High Density Multiplexer, 47-Channel, 2-Pole
40-640A-022-47/2
-
The 40-640A-022-47/2 is a 47-channel, 2-pole MUX and is part of a series of high density multiplexer modules featuring a choice of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PXI Single Bus 74-Ch 2A Fault Insertion Switch
40-190B-001
-
The Single Bus, 74 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
PXI 10W Programmable Resistor Module, 2-Channel, 1Ω to 239Ω
40-253-013
-
The 40-253-013 is a programmable resistor module with 2 channels which can be set between 1Ω and 239Ω with 1Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems
-
Product
1-Slot 3U VPX Development Chassis for Quartz Products
Model 8257
-
- 1-slot, small footprint development chassis- Optional dual MPO interfaces support 100 GigE- Supports VITA-66.4
-
Product
PXI FlexRIO GMSL Interface Module
-
Combines the Maxim Integrated Gigabit Multimedia Serial Link™ (GMSL™) interface with the Xilinx FPGA for high-throughput vision and imaging applications.
-
Product
PXI 4-Slot BRIC Matrix, 138x16, 1-Pole (6 sub-cards)
40-560B-021-138X16
-
The 40-560B-021-138x16 is an ultra high density matrix module and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI Vector Component Analyzer, 100 kHz to 32 GHz
M9816AS
-
The PXI vector component analyzer enables complex multiport device characterization with continuous wave and modulated signal measurements.
-
Product
Receiver, G20, Slide Mount, with Mounting Flanges for Pickering Chassis
310120143
-
Receiver, G20, Slide Mount, with Mounting Flanges for Pickering Chassis (40-908, 40-914, 40-918)
-
Product
PXI 2A Multiplexer, 2-Bank, 4-Channel 16-Pole
40-614-014
-
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
Product
PXI 8 Slot BRIC 220x4 2A 2-Pole Matrix
40-566A-104
-
These modules are 2 Amp high-density large PXI matrix modules with the ability to switch up to 2 Amps at 150VDC/100VAC. They are available in 4 or 8-slot PXI sizes and are constructed using quality electro-mechanical relays for high switching confidence.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-110-HI
-
The 40-230-010-HI (PXI) and 42-230-010-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 2.5Ω and 31.5Ω with 0.125Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
CDMA2k Analysis Using NI PXI RF Test Instruments
NI-RFmx CDMA2k
-
NI-RFmx CDMA2k is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development effort.
