Noise Monitors
-
product
20Hz Injection Kit Monitoring System
Signals & Systems India Private Limited
The Display used to monitor the 20Hz and 50Hz current passing through NGT transformer. This could help to monitor the stator earth fault and could record the current every minute. The current shall be displayed in milliamps for both 20Hz and 50Hz. If an earth fault occurs in the generator star point, the 20 Hz voltage drives a current through the fault resistance. The current can be measured using clamp-on CT which would be clamped between load resistor and NGT. It gives an indication of the current values are lower or higher than the set threshold.
-
product
Hydrogen Penetration Monitoring System
MS3112
The Hydrogen Penetration Monitoring System™ provides a method for directly measuring the rate of hydrogen migration through a vessel or pipe wall. This method actually measures the penetration current set up by the hydrogen as it moves through the steel. By sensing and recording this data directly from the pipe wall, this system offers valuable data which can only be indirectly inferred by other methods.
-
product
Surface Quality Monitors
PET manufactures and markets non-destructive, non-contact surface contamination and thin film detection models and automated systems (surface quality monitoring system) capable of detecting thin layer contamination, thin films and coating down to the Angstrom level. These systems represent a major breakthrough by providing, for the first time, a quantitative measure of surface cleanliness. As surface cleanliness verification instruments, in a part cleaning environment, these products are capable of validating the cleaning quality of all the part cleaning equipment available in the market. Any of SQM model series is capable of verifying metal contamination; monitoring absence/presence of organic and/or inorganic on virtually on surfaces of all metals. They are, price/performance, the most sufficient product available for testing surface of metals for surface cleanliness. These systems operate in an ambient environment, require no sample preparation or deposit of any agents on the surface. In any parts cleaning environment where the quality and efficiency of part cleaning equipment for removal of surface contamination is highly desired, these systems provide a scientific solution by quantitatively measuring the surface cleanliness. The SQM series has the sensitivity and operational simplicity required to provide fast and cost effective surface evaluation for all metals.
-
product
Panel Mounted Power Quality and Energy Monitor.
PM7503
The PM7503 Power Quality and Energy Monitor is a panel mounted variant of our top of the range PM7000 Power Quality Analyser. As with the PM7000 and P7000FLM, as well as recording all other important power quality parameters, the PM7503 with the optional Interharmonics upgrade is able to record 100 Voltage or Current harmonics on all 4 inputs at the same time.
-
product
Clamp type AC Current Sensor／for Power Monitor
CT-80PB
MULTI MEASURING INSTRUMENTS Co., Ltd.
*BIG CT WINDOW*AC 1A～500A*Current measurements of main cable
-
product
HF Low Noise Amplifier
The COMM-connect HF Low Noise Amplifier can be used to amplify signals in the HF frequency range. The amplifier comes with a selection of 4 different connectors, which makes it very easy to adapt to any type of installation. Mechanical mounting is made easy by mounting flaps protruding the casing.
-
product
Active Monitoring or Synthetic Transactions
CloudReady
Always-on, end-to-end user experience monitoringNo complex scripting required, Exoprise maintains the actions the sensors takeMonitors app performance via both Web UI and API transactionsFull network path performance information for correlation and outage detection
-
product
External Pyrometric Camera for Combustion Thermal Monitoring
PYROSCAN-U
Pyroscan-U is specifically designed to perform thermal monitoring and mapping of any object inside a kiln, furnace, boiler or reactor, while looking at the area of interest through a standard window, from outside the combustion chamber. This megapixel pyrometric camera captures both visible and infrared HDR (High Dynamic Range) images of the burning zone.
-
product
Thin Film Composition and Thickness Monitor
P-1000
The Precision P-1000 readily analyzes compound thin films utilized in semiconductor, superconductor, magnetic and applications.
-
product
Low-PIM, High-Power Filter Solutions for Monitoring Broadband Emissions
Enables monitoring of PIM to 13 GHz; 100W CW and 1KW peakNear-end monitoring: Carriers rejected -90dB by the notchtravel through the bandpass filter to the low PIM termination.Far-end monitoring: Carriers rejected -90dB by the highpass,IM products passed are monitored by the spectrum analyzer.
-
product
Monitoring & Management
Avocent®
The Vertiv ™ Avocent® (ADX) ecosystem is a series of IT Management devices and software that provides solutions in edge, enterprise and engineering lab environments. Built upon a secure common architecture the Avocent ADX ecosystem seamlessly integrates and scales to create an open yet resilient IT management fabric.
-
product
Automation Monitor
The Automation Monitor is a diagnostic system for remote analysis and troubleshooting of semiconductor capital equipment. The monitor is capable of delivering synchronous streams from strategically located video cameras, sound devices and data sources on the equipment.
-
product
PDS Wire Crane Monitoring System
It shows a real time overview of the wire crane in navigation, profile, and 3D views; displaying the clamshell, pontoon/vessel, design depths and color-coded digital terrain model (DTM). The navigation view highlights the high and low spots and is updated in real time, registering the progress of the dredging work. The registration follows the shape of the clamshell, bucket or orange peel bucket and is visible immediately in all views. The system also shows the open/close status of the dredge tool. Up/down indicators show the operator the exact distance to the seafloor and design depth continuously. 3D design models allow the use of complex designs.
-
product
Phase Noise Analyzer
NXA-6
This new NXA-6 is a sea-change in Phase Noise Test Systems. Making both residual and absolute noise measurements out to 6 GHz, this self-contained instrument uses either internal or external references with cross correlation for maximum dynamic range.
-
product
Battery Monitoring System
BMS-3923
Kongter Test & Measurement Co., Limited
This battery monitoring system is an innovative solution to measure battery condition with communication way of Power Line Carrier (PLC). With multi-frequency measurement, users can monitor and analyze battery in all aspects: internal resistance, voltage, current, capacitance, temperature and so on.Based on our years experience for battery management system, we build very mature mathematical model that precisely predicts battery capacity. This will in another hand reduce the time that we spend on capacity measurement using a battery load bank.
-
product
Tick-to-Trade Data Monitoring Appliance
NetTradeWatch™
NIKSUN NetTradeWatch™ is a tick-to-trade data monitoring appliance that is specifically software engineered to address the needs of highly dynamic and complex trading environments. NIKSUN NetTradeWatch™ combines the critical capabilities of multicast data monitoring, determination of data quality, and deep analytics related to transactions for 100% visibility into the financial network environments, making it the solution of the choice in a specialized market.
-
product
Low Noise Super Wide Band Amplifiers
WBA Series
WBA series low noise amplifiers have the octave bandwidth from MHz to GHz. With super low noise figure and exceptional low VSWR, WBA series LNA achieves exceptional gain flatness accross octave or multi-octave bandwidth.
-
product
Vacuum Process And Chamber Environment Monitors
Our process monitors are innovative in-situ process monitoring instruments that are fully integrated, application-specific packages, including component residual gas analyzers (RGAs), analytical equipment, and control software. Process mass spectrometers are used in varied applications, including; Semiconductor, Thin Film (CVD, Etch, PVD and degas), pharmaceutical lyophylization and bulk gas purity monitoring.
-
product
Log Management And Network Traffic Monitor
Derive Security Intelligence out of Network with Event Log Analyzer and Network Bandwidth Monitoring
-
product
USB Smart Noise Source, 500 MHz To 50 GHz, 5 DB ENR Nominal
U1832C
The USB-powered (USB TMC compliant) U1832C provides broadband noise figure measurements from 500 MHz – 50 GHz with modular signal analyzer, benchtop X-Series signal analyzers and Fieldfox
-
product
Process Ozone Monitor
Model 465M
Teledyne Advanced Pollution Instrumentation
The Model 465M is a microprocessor based medium range ozone monitor for measuring process ozone concentrations in water treatment, food processing, and research applications. The design has been specifically optimized for applications requiring the measurement of ozone at near-ambient pressure such as water treatment contactor off-gas measurement. The Model 465M has been designed to give accurate and stable readings over long time periods with little or no maintenance or calibration. The Model 465M is available in a NEMA 4X wall mount enclosure.
-
product
Analyze, Monitor and Control
Analysis Pack
Blue Cat's Peak Meter Pro plug-in will tell you everything about your audio levels. Blue Cat's FreqAnalyst Pro and FreqAnalyst Multi plug-ins provide extremely smooth spectrum and frequency content analysis. Finally, the StereoScope plug-ins series let you visualize the stereo image of your audio content in details.
-
product
15T Telemetry Running Line Monitor
RLM15T-3.0-T
The DLM 15T Telemetry Running Line Monitor measures the tension on a ropepassing through its three wheels. Typically used in cable laying and winch operationsto measure and record line tension. The robust and wireless design has become anindustry standard.
-
product
Ultra Low Noise DC Power Supplies
R4G Series
R4G series are series regulator system DC power supplies so that enabled setting and reading out more fine output with a 4-digit indicator on furont panel and a high resolution D/A and A/D converter adopted newly.
-
product
Chemitec Sensors And Analyzers To Monitor Oxidants In Water
Chemitec's S494 series of amperometric probes provide continuous, accurate monitoring of chlorine and other oxidants in clean water applications. A range of sensors assures accurate measurement of oxidation, with sensors optimized for Chlorine (total, organic or inorganic), Chlorine Dioxide, Ozone, Peracetic Acid, Hydrogen Peroxide, Bromine, or Chlorites.
-
product
USB Smart Noise Source, 10 MHz to 26.5 GHz, Nominal ENR 15 dB
U1831C
The USB-powered U1831C provides broadband noise figure measurements from 10 MHz – 26.5 GHz with modular signal analyzer and benchtop X-Series signal analyzers.
-
product
Telephone Line Monitor
AI-5120
The AI-5120 is a compact device designed for monitoring and analyzing signals present on the telephone line. By sensing the voltage present on the telephone line it detects and measures ringing, DTMF & pulse dialing, FSK (Bell 202 and V.23) signals, line polarity reversals, and open switching intervals (OSI). Working in conjunction with the TRsSim software on a PC, the AI-5120 becomes a valuable tool in analyzing and debugging Caller ID and SMS (Short Message Service) data transmission. Like an oscilloscope, it can capture and display waveforms showing various signals present on the telephone line.
-
product
In-line Sensor & Auto Range Switching Concentration Monitor
HF-960EM
Measures a wide range of HF concentration from low concentration to undiluted liquid. The HF-960EM achieves high precision measurement by the auto-correction range switching function. Also has the capibility of cleanliness with all PFA sensors. Measurement range: 0 - 50%.
-
product
End of Line Noise Test System
End of Line Noise Test Systems from VIacoustics are designed to support end of line product noise testing on factory floors and quality assurance environments. Using the Limit Analysis features of the Nelson Acoustic Trident software, users can set noise emission maximum, minimum or control range criteria based on Awtd and/or 1/N octave band criteria. Criteria can be customized for most any type of product based on the noise emissions of known good and bad units. The large front panel Pass/Fail indicator allows operators to quickly determine if units meet the criteria. Data on units that fail can be exported for further analysis.
-
product
Noise Dosimeters
Noise Dosimeters are wearable, portable, wireless (cable-free), personal noise exposure meters for occupational and workplace noise measurements. They are designed specifically to monitor an employee’s noise exposure in order to comply with Health and Safety regulations.
