-
product
Wire/Cable Harness Tester
PANTHER 4HT
Qmax Test Technologies Pvt. Ltd.
The Panther 4HT Wire \ Cable Harness tester is designed for Automotive and Semiconductor industry to apply in testing of wire harnesses, that needs testing during production with whole new fleet of features that make the task reliable, complete and fast. It uses innovative technology to test the impedance values. It can be interfaced to any type of fixtures as required. It uses the Learn and Compare technique for finding out opens or shorts in a harness. The learnt open / short combination from a Good Board is taken as reference and compared with the Board Under Test for any mismatch.
-
product
Edge Press Technology Bed of Nails Testers
Prober Edge Press Family
Production volume test fixture with swappable test plates, front and rear panel inlays, and multi-testing compatibility with process carrier pallets. Swappable test plates provide the ability for one fixture base to support a variety of units under test. Interchangeable front and rear panel inserts provide further customization. Interoperability with process carrier pallets provide multiple board testing capabilities, panelized testing, and flex circuit testing. A selection of interfaces to general testing equipment provide for a wide selection of customized testing features.
-
product
Debug Fixture
With at-speed test, debug can easily become a problem: If test points are on the bottom, as is often the case for test processing, then this requires the board to be flip over for the debug. However, during at-speed testing, key devices and signal paths are often on the topside. IST Engineering has in-house expertise with debug fixtures, which allow the test technician to flip over a test board, or even hold it vertically for dual-sided access, while still running the Device-Under-Test at full-speed through card-edge connectors - whether these are standard DIN type or F or N type co-ax connectors. The debug stations are constructed robustly, with metal frames and high-grade flexible cabling and can also be used as backup test stations in a manufacturing flow. They can be built with custom machined waveguide connections for RF/Microwave applications, or with standard, off the shelf connectors, as defined by the application. A number of these debug fixtures are in production use with a range of customers.
-
product
In-Circuit Test Fixture Design Services
An integral part of board test is the test fixture. Innovations in board technology may manifest themselves as challenges in test fixture design. Utilizing a creative & systematic design philosophy, Acculogic consistently delivers state of the art solutions for the most complex test interface problems.
-
product
SMT & THRU HOLE LOADED BOARD TEST PROBES
SERIES 33
ElectricalMAXIMUM CURRENT:3 amps continuousat working travel, non-inductiveRESISTANCE: At 35 mA test current,20 mOHMS meanMaterials and FinishesPLUNGER: Heat treated berylliumcopper, 24Kt gold plated over nickelBARREL: Nickel silver with preciousmetal clad ID.SPRING: Music wire, silver plated
-
product
K-Base Test Board Adapter
1180
The TESCO K-Base Test Board Adapter allow quick, convenient testing of self-contained K-Base meters on test boards designed for socket type meters. The K-Base Test Board Adapters are designed for single phase (Catalog No. 1180-2) and polyphase (Catalog No. 1180-4).
-
product
VME Test Extender 3U/220mm J2
111EXT3122-12XX
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
Clamshell Type Mechanical Fixtures
Series 30
Semco’s GR Series 30 mechanical kits are an inexpensive solution to printed circuit board testing that requires the benefits of GR2270 style (VG) interface compatibility.
-
product
Fire Control System
MS 1120
PCI Based BTA is used to test FCC System Processor (8086) & Analog Boards. This system consists of a PC-AT, Digital Input / Output (DIO) Board and Analog Input / Output (AIO) Board to provide the necessary input/output signals to/from the board to be tested.
-
product
Clamshell Type Mechanical Fixtures
Series 70
The VP Series 70 Mechanical Test Kits provide a solution to printed circuit board testing using the Virginia Panel ITA G12 Interface.
-
product
Solid Pins
Advanced Probing Systems, Inc.
APS produces electro-chemically machined pins in diameters between .020"-.040" in a variety of materials for use in various applications. These “large diameter pins” are used in various medical applications, industrial applications, board testing, LED & LCD test and as components in small tools. APS’s design services can help you select the optimal material from tungsten, beryllium-copper, Paliney 7® or various stainless steel alloys or work with the material of your choice. Pins can be produced with either a sharp or radius (rounded) tip. Tapers can be highly polished, slightly polished, matte or neutral in finish.
-
product
Bypass Diode Thermal Test System
King Design Industrial Co., Ltd.
* Power: the heating board control panel uses 220V single-phase power.* Power consumption: 1.0KVA, 1000W(Max)* Volt: 220VAC* Current: 4.5A* Heating board: one controller per board* Power rate: room temperature raise to 75°C± 5°C within one minute.* Heating board dimension: 500mm x 1,000mm* 6-sheet electrical heating boards test: used to test the 2,200mm x 2,600mm module. It can be customer-designed.* The length of board power cable and thermal sensor cable shall exceed 3,000mm.* To get uniform heating effect, the electrical board is sandwiched by 2mm aluminum sheets at both sides of board.
-
product
Wireless Functional Test Fixtures
Circuit Check’s wireless fixture technologies reduce debug time, simplify ECO’s and reduce maintenance. This allows for the highest test performance, ability to probe denser smaller targets and achieve ultra-high node counts. Higher density more complex circuit boards complicate testing requirements. Smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board (T-Board).
-
product
1149.1 Boundary Scan Feature, GTE 10.00p
K8212B
Boundary scan is a method for testing interconnections on printed circuit boards. Keysight’s Interconnect Plus Boundary Scan feature enables all the tools required to develop and execute this foundational test method on the board under test.
-
product
Air Data Computer (ADC) Tester
MS 1122
The ADC tester is used in 2nd line maintenance is to check the functionality of ADC. This unit is a rugged customized hardware based on full functionality test of ADC. The Air Data Computer (ADC) Tester is a fully automated GO/NOGO tester with full functional testing in 2nd line maintenance. This tester is to test ADC at unit level and identify faulty Shop Replaceable Unit (SRU). This tester is also used to carry out PI checks on ADC before clear them for installation on aircraft. ADC Interface board designed to test full functionality of ADC. The Air Data Computer (ADC) test equipment shall be used for testing ADC of Tejas Aircraft. ADC test equipment shall verify the functionality against specifications during second line maintenance and pre-installation on the aircraft.
-
product
Actuation Methods for In-Circuit Test Fixtures
Commonly referred to as In-Circuit Test (ICT), loaded board test can be defined as the task of measuring values of components that have been installed on a printed circuit board (PCB). A second basic category of loaded board test measures simple open and shorts on the board to verify manufacturability standards. Circuit Check supports all forms of in-circuit test strategies with its Performance Grade and Value Line test fixtures.
-
product
1149.6 Boundary Scan Feature, GTE 10.00p
K8213B
Keysight’s Interconnect Plus Boundary Scan 1149.6 feature enables all the tools required to develop and execute this test method on the board under test. Compared to the 1149.1 standards, the 1149.6 standards define test methods for the boundary scan devices that are designed with AC coupled signals or differential nets needed for high-speed operations of the device.
-
product
High-Speed Embedded Host Electrical Test Board
HSEHET
High-Speed Embedded Host Electrical Test Board is approved by USB-IF, specifically designed for the electrical test of USB embedded host products.
-
product
In-Circuit Test Systems
Keysight offers leading board test solutions for electronics manufacturers to tackle a wide range of PCBA test access and coverage issues for today's complex printed circuit assemblies.
-
product
PCBA Pattern Analyzer
A222917
Chroma A222917 is a multi-functional PCBA main board board signal test device for display. It has ultra high speed LVDS (Low -voltage differential signaling) as image signal analysis core to provide high efficiency and stability test quality.
-
product
FRAMOS SLVS-EC RX IP CORE
Sony’s SLVS-EC interface standard has emerged as the best high speed interface to Sony’s best image sensors, enabling higher throughput, greater signal integrity, and simpler designs. Engineers developing solutions using Xilinx FPGAs and SoCs can take advantage of FRAMOS’s SLVS-EC RX IP Core, Evaluation Board and tested source code examples. Device builders and camera vendors can de-risk the design while reaping the benefits of Sony’s latest high-speed interface.
-
product
Test Probes and Pins
Spring Loaded Test Probes for Circuit Board Testing, "Pogo Pins" Test Electronics sources and stockes a large variety of Test Probes and Spring Loaded Test Pins. Let our applications engineers help you find the correct pin for your test fixture application.
-
product
Semi-automatic Three-phase kWh Meter Test Bench
SY8310
Hong Kong Songyang Industrial Ltd.
The new SY8310 series semi-automatic three phase energy meter test board, designed according to International Standard, is a newly developed ideal measuring equipment for energy meters. The equipment can be operated easily through test board button to preset directly all data of meter under test and test process.
-
product
Backplane Test System
402HV
Our model 402HV is the result of 25 years of high voltage / high pin count test systems experience. We produced our first high voltage system back in 1985. It was programmable up to 600 volts / 600 Mohms and had over 49,000 test points. It could test a 5k point board in less that 15 seconds. Since then we have built hundreds of high voltage test systems, with our highest voltage system capable of testing up to 2000 Volts DC / 1500 Volts AC. (One of our 600 volt systems, built in 1986 is still in operation testing boards for a defense contractor.)
-
product
Printed Circuit Board Testing Solutions
IES Systems is a turnkey test systems solution provider with 10 years of proven experience in printed circuit board testing solutions. Our experienced engineers design electro/mechanical solutions to interface between your product and our custom designed test instrumentation. We provide a complete solution to your PC board testing needs.
-
product
Test Points, Tips, Probes, Jumpers and Clips
Nickel Plated Steel Alligator Clips. PTFE Insulated Terminals and Test Point Jacks. Circuit Board Test Jacks and Plugs. Color Coded PCB Mount Test Points, Loop Style with Plastic Base for Snap-In Mounting. Surface Mount Test Points on Tape and Reel.
-
product
VME Test Extender 9U/400mm J1/J2/J0
111EXT9140-0120
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
High Flexibility Test Controller Card
TCC 1800-UE
The TCC1800-UE Test Controller Card is a generic control board for production testing of printed circuit boards (PCBs). The board is controlled by a command language on a PC to which it is connected via Ethernet.The TCC1800-UE is designed to work with positive voltages up to 24V. The card provides extensive IO: Analog and digital interfacing, counters, PWM outputs, bidirectional I/O, ethernet-, CAN, USB, SPI and I2C interfacing.
-
product
Silicon Test & Yield Analysis Solutions
Tessent®
The Tessent product suite combines features of deterministic scan testing, embedded pattern compression, built-in self-test, specialized embedded memory test and repair, and boundary scan, as well as board and system-level test technologies. This comprehensive silicon test and yield analysis solution is built on the foundation of the best-in-class solutions for each test discipline
-
product
6 Sided Bed of Nails Testers
BoxProber Family
6 sided Bed of Nails circuit board test fixture. Probes top bottom and all 4 sides. Central camming mechanism pull plates inward. Mechanically or electrically actuated options. Designed primarily for testing products in plastics. Side access electrically probes outside panel connectors. The unit will also optically read LEDs and key segments off LCD displays. Solenoids will press buttons and servos will turn selector switches. DC motors are used to adjust multiple turn potentiometers. Microphone will detect audio output tones. Top and bottom of circuit boards can also be probed if removable access panels are available. This unit will also probe all 6 sides of a circuit board. This is typically utilized in applications where connector testing is required.
