-
product
6-24V Multi-functional Auto Tester With LED Display
6510A
Peaceful Thriving Enterprise Co Ltd
Test the automotive electrical system within 6-24V. In order to save the testing hours for the automotive electrical system, the tester is designed to test the system without re-connection between the vehicle battery and the testing components. For the testing and safety purpose, the tester contains short-circuit protection, which can also check the ground connection without voltage drop test. The short-circuit protection system contains the recoverable fuse, so the technician will not waste the fuses during the testing. The extension cable is long enough for a technician to test the whole system for the vehicle. Therefore, the technicians do not have to search for ground connection constantly.
-
product
RF Shielded Chamber
MIL-STD
A high performance RF-shielded chamber specifically designed for radiated emissions testing in accordance with MIL-STD-461E/F. This chamber can be used for conducted emissions, conducted immunity, radiated emissions, and radiated immunity testing.
-
product
PXI Resistor Module 2-Channel 1.5R to 8.19k with SPDT
40-293-124
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
IP Fax/ Modem Testing
To successfully deploy fax services requires extensive network design, test and traffic engineering. Test equipment can prove valuable in this process, if it can: Generate and receive fax signals in bulk over wired and wireless networks, monitor and distinguish fax signals in real time for traffic engineering and network design purposes, and analyze fax signals after capture for troubleshooting failed or poorly handled calls.
-
product
Gearbox Tester
The gearbox tester was designed to test the Azimuth Drive Unit (ADU) for a missile launcher. The ADU is the horizontal position controller for the launcher. It consists of a main drive shaft, a manual drive shaft and an output drive shaft. This system uses a multi-axis motion controller to operate.
-
product
Cable Test And Fault Location Systems
Power outages can cause serious financial and social damage, as they disrupt the normal operation of security and life support systems, destabilise the operation of industrial facilities, transport network, and utilities. Reliable power distribution is ensured by an effective prevention and prompt elimination of cable faults and electrical equipment failures. KharkovEnergoPribor Ltd. offers a range of integrated solutions designed for testing power cables and electrical substation equipment, as well as locating various types of faults in underground utilities.
-
product
Dual Surge Current Generator
MIG0612T-K12
Designed for testing telecom surge protection devices according to ITU-T K12. The generator has two indepedent impulse outputs which allow testing of two and three terminal protection devices such as gas discharge tubes (GDT). The generator can be configured for two terminal devices or with the outputs in parallel to increase the current impulse for two terminal devices.
-
product
PCI High Density Potentiometer Card 4-Channel, 16-Bit, 0 To 65k Ohm
50-296A-121-4/16
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
DIELECTRIC and CONTINUITY TESTERS ( HI-POTS )
AV-25V-GC1-05
This tester is designed for testing equipment wiht a line cord which can be plugged directly to the tester. The continuity test is to determine whether the ground wire of the line-cord is well connected to the metal frame of the unit under test.
-
product
Cable Manufacturing
For years, we’ve been at the forefront of optimizing and automating how cable manufacturers test their fibers. Whether it’s cable design qualification, in-process testing, or final quality control—PK instruments around the globe are running 24/7 measuring thousands of fibers.
-
product
ICT/FCT-Fixtures
We offer a wide range of testing fixtures. In Circuit Test fixtures, Functional Circuit Test fixtures, small and simple fixtures up to large special designed testing solutions.
-
product
PXI Resistor Module 4-Channel 1R to 127R with SPDT
40-293-112
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
High-Performance Application and Security Load Module
PerfectStorm 10/1GE Load Module
Keysight Network Applications and Security
Equipped with powerful multi-core, multi-threaded network processors, PerfectStorm 10/1GbE is designed to satisfy the testing needs of manufacturers needing speed flexibility in their testing resources. Networking equipment manufacturers building new equipment or service providers and large enterprises integrating this them benefit from testing and verifying performance and functionality prior to deployment.
-
product
Massively Parallel Board Test System
I7090
The Keysight i7090 is a massively parallel board test system designed to help PCBA test engineers improve manufacturing efficiency while reducing costs. Unlike traditional in-circuit testers, the i7090 supports up to 20 In-Circuit Test cores in parallel, which means engineers can test multiple Units Under Test (UUTs) simultaneously without the need for multiple systems. This reduces scaling and infrastructure costs and frees up valuable testing space.
-
product
PXI Resistor Module 4-Channel 1R to 63.7R with SPDT
40-293-111
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Laser Diode Characterization System
58620
The Chroma 58620 Laser Diode Characterization Station is a state-of-the-art full turnkey system specially designed for laser diode testing. Features range from macro inspection of the facet or aperture active area to a full suite of electro-optical parametic tests.
-
product
Automated Electrical Insulating Gloves Tester
CBC-12C
Automated system СВС-12С is designed for electrical withstand testing of rubber insulating gloves with an AC voltage (UAC ≤ 10 kVRMS) at industrial frequency (f = 50 Hz).
-
product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 1.02k Ohm
40-294-021
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Towing Dynamometer
RS-10K
RS-10K Towing Dynamometer is designed for testing today’s mid-sized cars and SUVs. The RS-10K is built with an all aluminum frame, an aerodynamic body and rides on an independent, air ride suspension and uses an eddy current absorber with special high temperature coils to absorb energy. The RS-8K is powered by an industrial generator, so unlike battery/alternator Towing Dynamometers, there are no lead-acid batteries to charge and testing time is unlimited at low speeds.
-
product
Desktop Appliance for PCI Express® Gen4
DE200-G4
A versatile test system designed to test and debug solid state drives (SSDs) of all popular storage interfaces and protocols, such as PCIe, SAS, and SATA.
-
product
PXI Resistor Module 2-Channel 1.5R to 4.09k
40-293-023
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
System on Demand (SoD): HiL Test System
System on Demand (SoD) is a unique, agile and standardized principle to design HiL test systems. SoD shifts the focus away from technical-only solutions to a proven automated design process – targeting our customer‘s real issues: time, budget and flexibility.
-
product
Benchtop & VXI Instruments
NAI offers a wide range of Benchtop and VXI card-based motion simulation and measurement instruments specifically designed for defense, commercial aerospace and industrial applications. Noted for their best-of-breed performance, these innovative and highly reliable instruments are used in a broad range of programs by customers world-wide. Typical applications include design; simulation; production test; and calibration of airborne, ground-based, and shipboard systems such as navigation control, signal retransmission, fire control, LVDT/RVDT simulation, and test.
-
product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 16.3k Ohm
40-294-031
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCIe® Gen5 NVMe SBExpress Test System
SBExpress-RM5
The SANBlaze SBExpress-RM5 is a complete turnkey PCIe® Gen5 NVMe SSD Drive validation test system. The SBExpress-RM5 feature set provides unique functions applicable to all aspects of a product lifecycle, from development and QA, to design validation and manufacturing test cycles. The ability to drive Gen5 NVMe SSDs with a wide range of configurable attributes provides engineers with a flexible, multi-controller supported validation test platform. Development, qualification, and certification test cycles can be highly automated, thus reducing overall test time, and rapidly surfacing errors and non-conformance.The SANBlaze SBExpress-RM5 hardware provides a rackmount chassis with sixteen dual or single port front-accessible drives.
-
product
Manual Testing Services
With manual testing services, we will hand-pick a team dedicated solely to your project. Our professionals will work with your developers, business analysts, and managers to go over requirements, build a comprehensive test plan, design thorough test cases, rapidly execute the tests, help remediate defects, and retest until the project is satisfactorily completed. The same individuals will be with you from beginning to end, so they have a complete understanding of the project and how you want it done, and you will always know exactly who you are dealing with. The same QA Engineers that develop the test cases will also execute them, leaving no room for misunderstandings and greatly expediting the process.
-
product
Oil Tan Delta Tester / Tester System
The instrument is designed to test the insulation resistance of electronic and electrical components in the range of 1 Meg ohm to 10 Million Meg ohm.
-
product
6U And 7U VPX 1 To 15 Slot Power & Ground Only Backplanes
101VPX6xxP-xxxx
Elma’s 6U / 7U VPX power and ground only backplanes provide a cost-effective way to design and test cards using the VPX architecture. The only assigned pins are for 3.3V, 5V and 12V power, and both ground and utility planes are defined.
-
product
Test Systems
This measurement system is the state-of-the-art acoustical analyser from Norsonic. Using the experiences and accumulated know-how from the previous generations of analysers, Norsonic is offering a multi-channel system with focus on user friendliness, high efficiency, and accurate reporting. The system has been designed for field testing as well as demanding accredited lab measurements.
-
product
Towing Dynamometer
RS-125K
RS-125K towing dynamometer is designed for testing Class A trucks and is the most full-featured, reliable and accurate towing dynamometer in the industry. The RS-125K is built with a heavy-duty steel frame, heavy-duty industrial axles and rides on an air ride suspension. The RS-125K is designed to maintain 125,000 Newtons of constant drawbar pull and the ability to simulate an uphill slope of 25%. The towing dyno uses absorbers with special high temperature coils powered by an industrial generator so there are no lead-acid batteries to charge and testing is unlimited at low speeds
