Filter Results By:
Products
Applications
Manufacturers
-
product
cPCI Data Acquisition
The cPCI data acquisition product line provides a variety of high-speed digital conversion cards from 50MS/s, 100MS/s, 500MS/s to 4GS/s. These conversion cards feature 8-, 10-, and 12-bit resolutions, as well as wide bandwidth and large acquisition memory. The high-speed digitizer, when configured into a data acquisition system, provides basic multi-channel oscilloscope functionality in a compact chassis.
-
product
48 Channel Threshold Comparator FPGA PXI Card
GX3748
The GX3748 is a user configurable, FPGA-based, 3U PXI card which features 48 voltage comparator channels. The daughter board interfaces to the GX3700 FPGA baseboard which employs the Altera Stratix III FPGA. Each input channel can accept input voltage signals from 0 to 50 volts, with programmable threshold levels. Three of the 48 channels are supported by the board's timestamp event feature.
-
product
3U CompactPCI Serial 2-Port CAN From PEAK Module
cPCI-A3CAN
- Follow PICMG® CompactPCI® Serial design guide- CompactPCI® Serial, 3U 4HP- 2x D-Sub CAN ports in front panel- Operating temperature: -40°C to +85°C- Designed to meet EN50155 standards
-
product
PCIe 16 Bit Multi-purpose Digitizer - up to 20 MS/s on 8 Channels (Single Ended) or 4 Channels (Differential)
M2P.5923-X4
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
product
PXIe 8 Bit High Speed Digitizer - 1.25 GS/s on 4 Channels, 500 MHz Bandwidth
M4X.2212-X4
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
PCIe 16 Bit Multi-purpose Digitizer - up to 5 MS/s on 4 Channels (Single Ended) or 4 Channels (Differential)
M2P.5916-X4
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
product
RazorMax Express 16 CompuScope 16-Bit, 1 GS/s, PXIe Gen3 Digitizer / Oscilloscope
The GaGe RazorMax Express CompuScope PXIe Gen3 x8 digitizer features unprecedented speed and resolution with either four or two 16-bit channels at 1 GS/s and 600 MHz bandwidth, and PXIe Gen3 data streaming rates up to 5.2 GB/s in a 3U Single Slot PXIe form factor.
-
product
PCIe 16 Bit Multi-purpose Digitizer - up to 125 MS/s on 4 Channels (Single Ended) or 4 Channels (Differential)
M2P.5966-X4
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
product
High-Throughput, 12-bit, 5 GSPS Digitizer
ADQ32
ADQ32 supports sustained streaming of up to 7 Gbyte/s either to the host PC or via pinned buffer to graphics processing units (GPUs).
-
product
14-Bit Digitizer
PA72D14130
The PA72D14130 is a 14-bit digitizer, capable of capturing waveforms at speeds up to 130Msps. An onboard offset voltage source allows capturing offset signals while still using the optimal range for maximum ADC utilization. Two onboard filters allow suppression of out-of-band noise. The 64MWord onboard memory enables capturing very long waveforms, or sequentially capturing multiple signals with minimal intermediate bus communication.
-
product
Multi-Channel 10-Bit Digitizer
ADQ8-8C
With compact modular form factors, 8 channels per board, and high-precision multi-board synchronization capabilities, ADQ8-8C is ideal for massive multi-channel implementations.
-
product
PXI FlexRay Digitizer
PXD7113
The PXD7113 FlexRay Digitizer features a 100MS/s input with 16Bit resolution, input voltages up to ±10V and a bandwidth up to 10MHz. The PXD7113 FleyRay Digitizer has a 2MB memory which allows up to1 million samples. The device has a high common mode rejection ratio (CMRR).
-
product
PCIe 12-Bit, 6 GS/s, Gen3 Digitizer
EON Express CompuScope
The GaGe EON Express CompuScope PCIe Gen3 digitizer board features unprecedented speed and resolution in a 6 GS/s streaming digitizer with 1.75 GHz bandwidth and PCIe data streaming rates up to 6 GB/s.
-
product
PXIe 8 Bit High Speed Digitizer - 1.25 GS/s on 1 Channel, 500 MHz Bandwidth
M4X.2210-X4
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
VXI High Performance Digitizer
VX2022
The VX2022 is a high-speed (20MS/s), 12Bit, digitizer for high performance measurements. Up to two input channels can be installed in the VX2022 with standard 2MS (4MByte) of memory. The VX2022, "C" size single slot VXI module, is designed for high throughput testing. Multiple measurements in combination with the memory segmenting feature results in additional test time improvement.
-
product
PCIe 16 Bit Multi-purpose Digitizer - up to 125 MS/s on 2 Channels (Single Ended) or 2 Channels (Differential)
M2P.5961-X4
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
product
PCIe 16 Bit High Speed Digitizer - 180 MS/s on 4 Channels
Your product description goes here.
-
product
PCIe 16 Bit Multi-purpose Digitizer - up to 80 MS/s on 2 Channels (Single Ended) or 2 Channels (Differential)
M2P.5941-X4
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
product
16-Bit Multi-Function With A/D, D/A And Digital I/O Channels CPCI Cards
GX3232 Series
The GX3232 is a multi-channel 16-bit, analog input and output cPCI module, supporting 32 single-ended or 16 differential input channels and four analog output channels. The inputs can be software configured for differential or single-end operation and are sequentially scanned with a maximum aggregate scan rate of 300 kS/s. Three input ranges are software-selectable: ±10 V, ±5 V or ±2.5 V. Optionally, the GX3232 is available with a high voltage input configuration and supports three ranges: ±60 V, ±30 V and ±15 V. The high voltage configuration supports 16 single-ended or 8 differential input channels for high voltage and 16 single-ended or 8 differential inputs for low voltage measurement. Four analog output channels provide software-selectable output ranges of ±2.5 V, ±5 V or ±10 V. The outputs can be updated either synchronously or asynchronously and support waveform generation. Each output can be clocked at rates up to 300 kS/s. A 16-bit digital I/O port is also provided, which supports 16 bidirectional data lines. Note that when used with a TS-700 system only 8 of these digital I/O lines are available at the test system's receiver interface.
-
product
8-CH 14-bit 100 MS/s High-Speed PXI Express Digitizer
PXIe-9848
The ADLINK PXIe-9848/9848H is an 8-channel, 14-bit, 100 MS/s digitizer delivering both high-accuracy measurement results and high-dynamic performance. With a PXI Express bus interface and ample onboard acquisition memory up to 512 MB, the PXIe-9848/9848H can easily manage simultaneous 8-CH data streaming. High density and high speed digitizer features ideally position the PXIe-9848/9848H for applications such as LIDAR, radar signal acquisition, and PSU (Power Supply Unit) testing applications.The PXIe-9848 provides a flexible set of input ranges from ±0.2V to ±2V, software selectable 50Ω or 1MΩ input impedance, a wide variety of triggering options and tight synchronization capability, all maximizing convenience of use. In addition, ADLINK provides the PXIe-9848H, features a x15/x50 signal condition module providing both high input voltage range of ±100V and high dynamic performance, delivering the optimum solution to measurement range expansion in a PXI system.
-
product
4-CH 12-Bit 80 MS/s PCI Express Digitizer
PCIe-9814
The ADLINK PCIe-9814 is a PCI Express digitizer providing speedy, high quality data acquisition. Each of the four input channels supports up to 80MS/s sampling, with 12-bit resolution A/D converter. This allows simultaneous recording of signals on all channels with no inter channel phase delay. The extremely large on-board memory enables long recording times even at the highest sampling rates.Unlike parallel PCI buses, PCI Express slots utilize serial point-to-point connection. Each connection pair (lane) can achieve burst connection speeds of 250MB/s. The PCIe-9814, based on x4 lane slot PCI Express technology, provides a clear advantage in that direct connection of each slot allows full transfer bandwidth for each individual card. The ADLINK PCIe-9814 x4 digitizer can be used in any standard PCI Express slot, x4, x8, or x16.
-
product
PXIe-5775, 12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO Digitizer
785591-01
The PXIe-5775 is a PXI FlexRIO Digitizer that provides 6 GHz of AC-coupled analog bandwidth and 12 bits of resolution. You can operate the PXIe-5775 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. With a passband from 1 MHz to more than 6 GHz, the PXIe-5775 is ideal for high-bandwidth frequency domain applications, including radar prototyping, LIDAR, and communications. The FlexRIO driver includes support for finite acquisition, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
product
PCIe 16 Bit Multi-purpose Digitizer - up to 40 MS/s on 8 Channels (Single Ended) or 4 Channels (Differential)
M2P.5933-X4
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
product
PCIe 16 Bit Multi-purpose Digitizer - up to 20 MS/s on 4 Channels (Single Ended) or 2 Channels (Differential)
M2P.5922-X4
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
product
High-Speed A/D 12-Bit Digitizers
GaGe 12-bit resolution digitizer models divide the input voltage range into 4,096 different digitization levels, which improves the delectability limit by a factor of 16 over the 256 levels of an 8-bit resolution digitizer model.
-
product
PXIe-5764, 16-Bit, 1 GS/s, 4-Channel PXI FlexRIO Digitizer
785171-01
The PXIe-5764 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PXIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5764 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
product
PXIe-5763, 16-Bit, 500 MS/s, 4-Channel PXI FlexRIO Digitizer
785161-01
The PXIe-5763 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PXIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5763 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
product
PCIe 16 Bit High Speed Digitizer - 180 MS/s on 2 Channels
M4I.4470-X8
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
PCIe 16 Bit Multi-purpose Digitizer - up to 125 MS/s on 1 Channel (Single Ended) or 1 Channel (Differential)
M2P.5960-X4
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
product
PXIe Digitizer: 4 Channels, 2 GHz, 12-bit
M5200A
The M5200A is a single-slot PXIe four-channel, high-speed, analog to digital digitizer. It is a high-performance digitizer with easy-to-use programming libraries, real-time sequencing technology, and FPGA programming.
