Filter Results By:
Products
Applications
Manufacturers
Voltage Converters
Changes the voltage of a source.
-
product
Frequency Converter
Our frequency converters, which we offer with outputs of up to 500 kVA, can be used to supply alternating current consumers with constant voltages that deviate from the input network.
-
product
NI-9264, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
780927-01
25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The NI‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the NI‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection.
-
product
Analog Output Modules
D3000/4000
The DGH D3000/4000 series are complete computer-to analog output modules. They communicate, in ASCII, with RS-232 and RS-485 serial ports. Simple ASCII commands are used to control a 12-bit DAC (Digital-to-Analog Converter) which is scaled to commonly used current and voltage ranges.
-
product
AC DC Current and Voltage Converters
The DAT5023 I is an AC or DC current converter, the input current range is selectable on order from 0-5Amps, 0-10Amps, 0-20Amps, 0-25Amps, 0-30Amps, 0-40Amps, 0-50Amps, 0-60Amps. It measure the current with the use of a Hall effect transducer. There is a coil (current transformer) inside the current converter which is isolated from the current input. The cable passes through the housing of the converter and the coil and the true root mean square measurement is taken from this coil then converted to a standard industrial signal output.
-
product
ColorPAL Color Sensor
28380
The ColorPAL is a miniature color and light sensor which, through its RGB LED, doubles as a color generator. For sensing color, the ColorPAL uses its LED to illuminate a sample, one color component at a time, along with a broad-spectrum light-to-voltage converter to measure the light reflected back. The amount of light reflected from the sample under illumination from each red, green, and blue LED can be used to determine the sample’s color. The ColorPAL works with non-fluorescent reflective surfaces, preferably those in contact with its light shroud.
-
product
Current Source-Sink D/A Converters
Analog Devices’ current source D/A converters (DACs) portfolio is ideal for photonics control applications where low current noise density, low dropout voltage, and high power efficiency, in addition to high channel density, is critical to system performance. The flexibility of the configurable current source D/A converter outputs, and 300 mA current delivery, make them suitable for resistive heaters and proportional solenoid drive.
-
product
cPCI to PMC Compatible Adapter/Carrier
cPCIBPMC6UET
cPCIBPMC6UET ( cPCI to PMC ) adapter / carrier converter card provides the ability to install up to two PMC cards into a standard cPCI slot. cPCIBPMC6UET has two PMC card slots mounted to a universal voltage 6U 4HP cPCI card.
-
product
Frequency to Voltage Converters
Encore Electronics offers a complete line of frequency to voltage converters ranging from the economically priced and compact DIN rail mounted Model FL228 to the rack mounted Model 225. For applications requiring performance between these two models, we now offer our FL236 DIN-rail packaged Digital Frequency/Voltage converter, featuring fast response time, low power and compact footprint.
-
product
Digital Power Meter, 30A
66205
Chroma Systems Solutions, Inc.
Voltage Ranges:15/30/60/150/300/600 Vrms1200Vrms (optional)Current Ranges : 0.005/0.02/0.05/0.2/0.3/0.5/2/5/20/30 ArmsFrequency Range : DC, 15Hz~10kHzEmbedded high speed DSP, 16 bitsAnalog/Digital converters withmax samipling rate up to 250kHzCapable of meeting the IEC 61000-4-7harmonics measurement requirementsSmart Range function provides seamlesspower integration measurement underauto range modeSupports external shunt and CT forhigher current applications5 mA minimum current range &0.1mW power resolutionMeets ENERGY STAR /EN 50564/IEC 62301/ErP requirementsUser-define criteria providesautomatic PASS/FAIL indicationsTHD and user-specify order distortionmeasurementInrush current and energy measurementsVoltage/ Current harmonics measurementsup to 100 ordersUSB (Host) interface provides data loggingfunctionalitySupport GPIB, USB, RS232, LAN (option)interface
-
product
100-Watt DC/DC Converter
55LS1
NAI’s 55LS1 is a COTS, 100 Watt DC/DC Converter that accepts a +28 VDC input and provides a single full-power output at a baseplate temperature of +100° C.Standard features include remote error sensing; remote digital (TTL) turn on/off; and protection against transients, overvoltage, overcurrent, and short-circuits. Options such as ESS vibration testing and choice of output voltages are available, and additional options and special units can be ordered.
-
product
Non-Contact Type Magneto-Electric Rotation Detector
MP-9820
MP-9820 is a magneto-electric-rotation detector using an internal hall element, a permanent magnet, DC amplifier, and voltage regulator in its compact body. Using MP-9820 in combination with detection gear enables deriving stable rectangular waveform from ultra low speed all the way through high speed. (1 Hz to 100 kHz)MP-9820 finds wide range of applications and rotational measurement objects by using with TM-3100 series tachometer and FV-1500 FV converter.
-
product
PXI I/O Module for Sound and Vibration
JSV-4498-PXI
16-channel ICP analog voltage input Maximum sample rate: 204.8KS/s; simultaneous acquisition Analog-to-digital converter: delta-sigma, 24 bits Phase accuracy < 0.02deg@10KHz Maximum analysis bandwidth：96KHz Input range from ± 10 V to ± 316mV Coupled mode：AC Signal conditioning: anti-aliasing filter Digital filter: user-defined low pass, high pass, band pass, band stop Dynamic range：114 dB ICP Current：0-4 mA, optional Overload indication: software displa
-
product
Thin Film Current Sensing Chip Resistors
CSTN
*Thin film process*High power rating up to 3 watts in 2512 size*Resistance values from 50m to 1ohm*High purity alumina substrate for high power dissipation*Power management applications*Switching power supply*Over current protection in audio applications*Voltage regulation module (VRM)*DC-DC converter, battery pack, charger, adaptor,*Automatic engine control*Disk drive
-
product
Bench Electronic Loads
EL30000 Series
The Keysight EL30000 Series Bench electronic load with a built-in data logger provides new levels of test insights for your devices like power supplies, batteries, DC to DC converters, and more. View voltage and current trends to make real-time decisions, rather than waiting hours for a test to complete. At the heart of the EL30000 is a highly accurate measurement system that provides real-time updates to the large display. Keysight’s PathWave BenchVue software allows you to operate the electronic load remotely, execute test sequences, log data, and integrate with other test instruments. Single and dual-channel models are available with up to 600 W for measurements that require more power. Start your test with confidence and finish with results you trust.
-
product
Energy Saving Static Converter
The ENERGY SAVING static converter serves to generate a controlled squarewave single-phase alternate voltage (low frequency: 25 ÷ 125Hz) for industrial applications requiring high load power supplied by an external matching transformer. The power supply, sectioned by remote control switch and external fuses, is fed by a three-phase electric line via uncontrolled diode bridge and filtered by inductor and capacitor battery. The DC voltage thus obtained is converted into single-phase alternating voltage via “H”-shape bridge of semiconductors in order to control impressed frequency single-phase transformers.
-
product
A/D & D/A Converter Combinations
Analog Devices’ comprehensive portfolio of integrated monitoring and control components combine ADCs, DACs, temperature sensors, GPIOs, and current sensing technologies in a wide range of configurations. ADI integrated solutions save space over discrete implementations and simplify operations and provide the configurability your system requires. These products are ideal for general system monitoring of peripherals like power supplies or system voltages and currents. Used in wireless base stations, optical transceivers, transponders, and industrial systems such as building control, these converters offer versatility and flexibility.
-
product
PXIe-4302, 24-Bit, 32-Channel, 5 kS/s, ±10 V PXI Analog Input Module
783865-01
24-Bit, 32-Channel, 5 kS/s, ±10 V PXI Analog Input Module—The PXIe‑4302 is a filtered input module for voltage, thermocouple, and current measurements. The module has an A/D converter per channel to enable a simultaneous sample rate of 5 kS/s. The PXIe‑4302 offers you the ability to select a digital filter per channel to provide extra filtering performance. You also can operate up to four different sample rates and triggering configurations concurrently to ensure you measure every sensor as needed. The included NI‑DAQmx driver simplifies hardware configuration and measurement.
-
product
Single Channel USB Programmable Band-Pass Filter
USBPBP-S1
The USBPBP-S1 stand alone USB controllable module provides a single channel of high and low-pass filtering and high-quality instrumentation amplifier for front-end signal conditioning compatible with all popular A/D converter devices. The USBPBP-S1 is powered with 9 to 12VDC so it can be connected to a battery voltage source or the supplied 115-220VAC adapter may be used for operation with wall power anywhere in the world. When programmed from the USB port, the USBPBP-S1 will remember all of the programmed properties between power cycles. Program once and operate as a stand- alone signal conditioner without having to reprogram for every use. This is perfect for turn-key applications. It's easy to connect the USBPBP-S1 into the data collection system. Input and output signals can be routed through BNC connection or using the detachable screw terminal connectors. Optional SMA type adapters are also available.
-
product
Transistor Testing
Radiant is introducing an I2C digital-to-analog converter product that can be attached to the Precision Premier II and is controlled from Vision. The addition of this extra voltage source makes it possible for the Premier II to measure the performance of thin-ferroelectric-film gate transistors (TFFTs and MFSFETs). This document explains the theory for such testing and gives examples of such tests using Radiant's SFRAM transistors as examples.
-
product
NI-9264, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
785190-02
25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The NI‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the NI‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection.
-
product
Fully Differential Amplifiers
Differential amplifiers allow the process of single-ended input to complementary differential outputs or differential inputs to differential outputs. These amplifiers feature two separate feedback loops to control the differential and common-mode output voltages. Analog Devices fully differential amplifiers are configured with a VOCM pin, which can be easily adjusted for setting output common-mode voltage. This provides a convenient solution when interfacing with analog-to-digital converters (ADCs). ADI also offers a series of differential receiver products that convert differential input signals to single ended output.
-
product
NI-9264, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
785190-01
25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The NI‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the NI‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection.
-
product
System Components
System components and accessories complete the Bender product portfolio:Coupling devices for ground-fault monitoring at high voltages, analog measuring instruments, power supply units, interface converters and interface repeaters.Please contact us for advice regarding these and other system components.
-
product
16-Channel VME Analog/Thermocouple Input Module
V450
The V450 is a 16-channel 24-bit VME isolated analog-to-digital converter module which can acquire a wide range of DC voltages, including thermocouple readings with automatic cold junction compensation. Each channel is independently isolated with it's own A/D converter, signal conditioning, input protection circuits, and test relay.
-
product
PXIe-4310, 16-Bit, 8-Channel, 400 kS/s/ch, Ch-Ch Isolated PXI Analog Input Module
784813-01
16-Bit, 8-Channel, 400 kS/s/ch, Ch-Ch Isolated PXI Analog Input Module—The PXIe-4310 is a channel-to-channel isolated, filtered analog input module for higher voltage measurements. The module offers the ability to select an analog filter per channel to provide extra filtering performance. You also can operate up to four different input ranges per terminal block and triggering configurations concurrently to ensure you measure every sensor as needed. The module has an A/D converter per channel to enable a simultaneous sample rate at the maximum sample rate across the input range. The included NI-DAQmx driver simplifies hardware configuration and measurement.
-
product
High Voltage Power Supplies
The mains voltage (230V / 3 x 400V) is transformed, rectified and filtered by the HN series. The direct current output voltage is tuned by a variable transformer or regulated by a thyristor controller. With the HS and HV series the rectified mains voltage is supplied to a frequency converter, which produces a mid-frequency square wave voltage. This transformed, rectified and filtered alternating current produces the desired voltage as output, which is regulated by means of frequency variation or pulse width modulation. The equipment in the HV series supply, in addition to the high voltage output, up to 3 auxiliary outputs which can be used to supply e.g. heating, grid voltage or surge voltage.
-
product
100-Watt DC Power Line Conditioner w/Holdup
44LS1
NAI’s 44LS1 is a 100-Watt Power Line Conditioner with holdup time that protects downstream DC/DC converters from transients, low voltage conditions, and power interruptions. This unit accepts +28 VDC input and provides 22.5 to 30 VDC at 100 Watts to all downstream DC/DC converters.
-
product
Optical Delay
ODL
The Peregrine Optical Delay Line (ODL) provides an exceptional combination of precision, speed, and optical stability at a low price. It is ideally suited for pump-probe experiments and autocorrelation measurements (both interferometric and intensity methods). Advanced voice coil technology allows the ODL to be positioned anywhere in its travel range to within 150 nm. That’s 1 fs for a double-pass configuration. The response time is as short as 1 ms. Our 1-cm-travel ODL is interferometrically stable (measured using a 650 nm laser). No backlash, no hysteresis and no drive trains to wear out as with stepper motors. It’s convenient–the ODL can be positioned using digital commands, an analog voltage or a combination of the two. Two 16-bit on-board analog-to-digital converters simplify data collection. Digital inputs and outputs allow master or slave clocking. An executable Windows application is provided to get you up and running in minutes. In addition, DLLs and LabVIEW Vis for integration into your software are also included.
-
product
NI-9264, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
780927-02
25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The NI‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the NI‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection.
-
product
Autotransformer
T-1007
The Titan Series T-1007 Auto-transformer is used to conveniently scale the standard OV to 130V / 260V full scale Titan AC Power Source/Frequency Converter output to either X .5 stepdown (OV to 65V) or X2 stepup (OV to 520V). It has a 1.2 KVA power rating with excellent bandwidth and voltage regulation.The unit is of toroidal design, making it approximately half the size and weight of a comparable stacked laminate transformer. It is center filled with epoxy for isolation and durability, and features simple 1/4" bolt center mounting.
