Filter Results By:
Products
Applications
Manufacturers
Transducer Amplifiers
Increase a transducers signal to measurable levels.
-
product
6 Channel Signal Conditioner & Data Acquisition Module
DP-cPCI-1197
DP-cPCI-1197 is a high-resolution signal-conditioning module that amplifies the signals from full-bridge based transducers. This signal-conditioning module is available on a cPCI module form factor. This module has four gain settings to accommodate a wide variety of sensor output voltages. In addition, this module has an adjustable excitation voltage to accommodate transducer excitation requirements.A high resolution sigma-delta ADC and variable gain amplifier forms the core of the signal conditioning system. Direct digital conversion and digital isolation ensures a better signal integrity in comparison with the conventional analog system.
-
product
Turnkey Laboratory Acquisition Systems
Series 6800 for laboratory applications is a ready-to-run, high performance measurement system. Enclosures are 3U rack mountable or can be used right on the desktop. 6800 units come equipped with a conditioner, amplifier, filter and digitizer. Each channel has a front mounted connector specific to a measurement type: RJ-45 for 8-wire bridge transducers, BNC for voltage or ICP/IEPE inputs or a 3-wire military grade connector.
-
product
4-20mA Bridge AmplifierR
90416
This miniature, on-board, transducer amplifier is capable of supplying excitation voltage and amplifying millivolt signals from strain gage based transducers.
-
product
Signal Amplifier
ZET 412
The Signal amplifier ZET 412 with pseudo-galvanic separation is intended for amplification of input signals from various primary transducers and their transmission to the measuring unit (e.g., ZET 210 ADC/DAC unit) as well as for power supply of the connected sensors.
-
product
Single-Channel DC Powered Carrier Demodulator
CD16
The CD16 Miniature Carrier Demodulator is designed to deliver a 0 to 5 Vdc output from a variable reluctance transducer and operate from unregulated 9 to 55 Vdc power. A square wave excitation of 5 kHz is furnished to the transducer and the solid state integrated circuit amplifier and demodulator converts the transducer signal to an analog dc output. Zero and Span adjustments are made through access holes in the case.
-
product
Frequency Response Analyzers
Frequency Response Analysis (also referred to as Transfer Function Analysis) measures the output spectrum of a system relative to a stimulus, and is used to characterize the dynamics of the system under test. The technique measures the magnitude and phase relationship between output and input waveforms as a function of frequency. The input signals may be from a wide range of sensors including acoustic (microphones/sonar), mechanical (accelerometers/displacement transducers), optical (photodetectors), and electrical (amplifiers).
-
product
Electric Transducer Driver Amplifier
7620
The Krohn-Hite Model 7620 is a 17/34 watt, wideband power amplifier that offers extended output power and voltage capabilities. Performance features not available in other power amplifiers, the 7620 provides a differential output and is able to deliver 17/34 watts of continuous power (68 watts at dc) and 141V/282V rms (400V/800Vp-p). It can also provide plus and minus dc voltages simultaneously.
-
product
Load Cell Amplifiers
Datum Electronics load cell amplifier range is designed to increase (or amplify) a signal, generated by a strain gauge load cells with a full bridge connection, pressure transducers or torque sensors, allowing the user to use the data from the load cell in a more efficient and productive way.
-
product
Instrumentation
Unholtz-Dickie designs and manufactures a variety of transducer signal conditioners, accelerometers, remote charge preamplifiers, vibration monitors & limiters, transducer testers, buffer amplifiers and other special purpose instrumentation accessories for vibration testing.
-
product
Signal Conditioning System
28000
The Precision 28000 Signal Conditioning System makes it easy to manage a test with up to 256 channels of fully programmable transducer conditioning. Choose a mix of bridge, charge, IEPE w/TEDS, voltage (filter amplifier), strain, thermocouple, RTD/potentiometer, frequency, or other transducers. Self-tests traceable to NIST. 4, 8 and 16-slot rugged and transportable mainframes feature integrated cooling. Customize the 28000 for high-speed transient applications, static applications, or a combination of both.
-
product
Bridge Amplifier
90376
This miniature, on-board, transducer amplifier is capable of supplying excitation voltage and amplifying millivolt signals from strain gage based transducers.
-
product
Charge Amplifier
ZET 440
Charge amplifier ZET 440 for piezoelectric detectors is intended for:*amplification and conversion of output signals of primary piezoelectric transducers with charge output;*amplification and conversion of output signals of primary transducers with the IEPE type in-built electronics to voltage;*gain ratios: 1, 10, 100;*LPF: 0.1, 1, 10 Hz
-
product
6000 Series Analog I/O Modules
Series 6000 analog I/O modules condition, amplify, filter and digitize signals from virtually any transducer. All modules have conditioning & amplifier per channel and nearly all modules allow for setting bridge completion, shunt calibration, transducer power, gain, etc. individually per channel. Following the conditioning/amplifier stage, multi-pole Bessel or Butterworth analog filters are provided on each channel and can be set or bypassed individually by program control. A number of the modules include a high level analog output providing a conditioned/filtered output to a redundant, external A/D system. A 16-Bit Successive Approximation A/D follows the analog filter stage. Some modules use a single A/D with sample and hold while others have an A/D per channel. Sample rates are programmable per channel to easily accommodate mixing high and low speed measurements into a single data stream. Programmable hardware based warnings and alarms are included in the channel-by-channel architecture and are detected by digital output modules in the system, providing an ultra-low latency control capability directly from the data acquisition system.
-
product
High-Voltage Amplifier
ZET 420
The high-voltage signal amplifier for emission of acoustic signals through capacitive emitters: sonic detectors (without integrated amplifiers), piezoelectric emitters, and transducers.
-
product
Amplifier
AC-100
The voltage amplifier for connecting piezoelectric acceleration meters, microphones, and other primary voltage output transducers to FFT spectrum analyzers with the IEPE standard current output (ZET 017-U2, ZET 017-U8, A19-U2).
-
product
Signal Conditioners
Metra Mess- und Frequenztechnik in Radebeul e.K.
Metra has been manufacturing amplifiers for piezoelectric transducers for over 50 years. We offer economic charge amplifiers and signal conditioners for IEPE transducers including microphones.
-
product
Turnkey Portable Acquisition Systems
Series 6800 for portable applications is a ready-to-run, high performance measurement system that is DC powered for mobile applications. All connections are front mounted for easy installation in tight places or on the go. 6800 systems come equipped with a conditioner, amplifier, filter and digitizer. Each channel has a front mounted connector specific to a measurement type: RJ-45 for 8-wire bridge transducers or BNC for voltage or ICP/IEPE inputs.
-
product
Programmable Oscillator Amplifier
Computer Conversions Corporation
The Computer Conversions Corporation POA90-3 is a programmable quadrature oscillator with a built-in power amplifier, capable of driving current loads of up to 200mA. The sinusoidal outputs are 2.5Vrms signals that are phased 90° apart as REF out and REF out +90 (Quadrature), allowing the unit to be used with Synchro, Resolver, LVDT/RVDT, Inductosyn, or similar inductive transducers.
-
product
Synchro Power Amplifiers
SPA
Computer Conversions Corporation
The SPA Series "Pulsating" Synchro Power Amplifiers are proven, high efficiency, low cost, compact, reliable solid state synchro drivers; designed for demanding Naval/Maritime, Aircraft, fire control and radar/Antenna related, applications. They are commonly used on synchro based data transmission, re-transmission, simulation and instantaneous absolute position indicating and active control systems.
-
product
Synchro Power Amplifiers
SSP
Computer Conversions Corporation
The SSP Series are Compact, Reference Powered and Isolated Synchro Power Amplifiers, and AC Sine/Cosine ( Resolver ) to synchro converters; designed for moderate wattage, and re-transmission requirements; providing ultra high efficiency, and ultra high reliability in service, and ease of use. They are ideally suited for demanding Naval/Maritime, Aircraft, and Radar/Antenna related, applications. They are commonly used on synchro based data transmission, retransmission, simulation, and active control systems. They are suitable to drive both CT and CDX type passive loads, and virtually any synchro input instrumentation, or control.
-
product
Amplifier for the Frequency Range from 2 Hz to 50,000 Hz.s
Trig-Tek™ 203M
Versatile amplifier covers the frequency range from 2 Hz to 50,000 Hz.s and provides has three simultaneous outputs
-
product
Signal Amplifier
A10160
Model A10160 is an ultra-small footprint, wideband, DC coupled amplifier designed for high frequency, high current, signal amplification. With a high bandwidth of 45MHz, 34Vp-p into 50 ohms and up to 10W output power, the A10160 is the ideal complimentary amplifier to any signal source that needs a supporting power boost for demanding applications.
-
product
Signal Amplifier
9200A
Model 9200A was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It is built in a small case size to save space and cost but without compromising bandwidth and signal integrity.
-
product
Wideband Power Amplifiers
Krohn-Hite Wideband Power Amplifiers are designed to meet today's industrial needs where wideband, precision performance is required. Applications include: meter calibration, piezo transducer driving, bridging applications requiring high input and low output impedance, low distortion ac power source, ion beam deflection, vacuum tube driver, ink jet testing and design and many more.
-
product
PXIe Single Channel 20GHz 30dBm RF Amplifier
3201
Model TE3201 is a single channel RF amplifier in a single slot PXIe form factor that can operate from 100kHz to 20GHz, designed for high frequency, and high power signal amplification.
-
product
PXI Voltage Amplifier 10K Ohm, SMB
41-650-012
The 41-650 is a 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test. Each amplifier can be independently programmed to a gain of 1, 2, 5, 10 or 20, enabling it to be used with modules with low output voltage capability. Inputs and outputs can be provided either on SMB connectors or on a D Type connector to suite the user’s wiring system.
-
product
PXI Voltage Amplifier 10K Ohm, D Type
41-650-011
A 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test.
-
product
PXI Bus Signal Amplifier
3222
Model 3222 is a 3U single-slot, PXI-based power amplifier designed for signal amplification. Offering unmatched signal purity, Model 3222 amplifies signals from dc to over 20 MHz. The unit has a fixed gain of x10, however, the same amplifier is available with custom gain, with no signal purity or performance degradation.
-
product
Amplifier Operating with High Temperature Accelerometers Where Pyroelectric Effects May be Encountered
Trig-Tek™ 203PC-1/2
Operates with high temperature accelerometers where pyroelectric effects may be encountered, with frequency range from 3 Hz to 40,000Hz
-
product
Motion Control Terminal Board for Panasonic MINAS A4 Servo Amplifiers
DIN-814P-A40
This well-designed motion control terminal board is for the users who use Panasonic MINAS A4 super servo. With this terminal board, users can ealisy complete wiring with PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134.
