Filter Results By:
Products
Applications
Manufacturers
Thermocouples
Thermocouples are junctions of two dissimilar metals that produce a very small voltage proportional to the temperature of the junction.
-
product
Gauge Type T Thermocouple Wire
W-TW-40
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
product
Thermocouple Contact, ITA, Constantan, Type T(°C)
610113149
Primary mating contact 610113148.
-
product
Process Calibrator
MC-1000
The MC-1000 Process Calibrator provides high accuracy calibration, common DMM functions including read and source thermocouples, RTDs, Ohms, current, pressure, frequency and test continuity. This single calibration instrument will calibrate virtually any process device including: read and source thermocouples, RTDs, Ohms, Voltage, Current, Frequency, Pressure, and test continuity.
-
product
Independent 24-bit Sigma-Delta Type (One for Each Channel)
TR1
The TR1 provides 8 channels which can be individually programmed as a Thermocouple (TC) or a Resistance Temperature Detector (RTD) measurement interface. When configured as a TC, the channel can interface with virtually all thermocouple-type NIST temperature ranges. When configured as an RTD, the channel can interface to two, three and four-wire platinum RTD sensor configurations.
-
product
Temperature Meters
Omega offers a large selection of Temperature Meters that accept a wide variety of input signals including thermocouple, RTD, and thermistor.
-
product
MAX31856 Thermocouple Sensor Arduino Shield
SEN-30007-K
Quad channel thermocouple Arduino shield based on the MAX31856 universal digital thermocouple interface IC. This is an exciting update of the MAX31855, with improvements in resolution (19 vs 14 bits), on-board temperature reference (6 vs 4 bits), and compensation (fully compensated vs nonlinear correction required). The MAX31856 is interfaced via 4-wire SPI with options for interrupt triggering. An LDO and a high-speed level shifter are included on ALL device pins to allow interfacing with to any Arduino - both 3.3V and 5.0V variants - without sacrificing device performance in any operating condition.
-
product
Thermocouple, Contact, ITA, Chromel, Type K (°C)
610113133
Primary mating contact 610131131.Thermocouple contacts are manufactured from chromel or alumel alloys and color-coded for easy identification. Contacts are crimp terminated and easily inserted into the connector module. They can be readily removed from the connector module using a special removal tool.
-
product
Smart Probes
A wide selection of rugged smart probes for your sensing needs. From non-contact IR sensors to a full range of sensor types including Temperature, Humidity, Process, RTD, Thermocouple, pulse.
-
product
Submersible, Thermocouple Based Temperature Data Logger
TCTemp1000
The TCTemp1000 is a rugged, submersible, battery powered, thermocouple based temperature data logger. This is a stand-alone, compact, portable, easy to use device that can measure and record data for up to 16,383 measurements per channel. The storage medium is non-volatile solid state memory, providing maximum data security even if the battery becomes discharged. Its real time clock ensures all data is time and date stamped.
-
product
Low-Thermal EMF LXI Matrices
Pickering low-thermal EMF LXI matrices offer excellent thermal stability and substantially reduced thermal EMF figures when compared to a conventional switching matrix. Typical applications include signal routing in automatic test equipment, selecting thermocouple inputs, switching amplifier gain circuits and high accuracy DC microvolt measurements.
-
product
Thermocouple Thermometer 1 Input
HD2108.1
Thermocouple thermometer with one input for K, J, T, R, N, S, B, E type probes with miniature connector.
-
product
Portable Temperature Monitor
PTM1
The Model PTM1 is a high performance, precision hand-held instrument for the measurement of temperature using Physitemp’s Type T (copper-constantan) thermocouples (will also accept J & K). This versatile instrument measures temperature in both °C and °F. The internal memory of the microcomputer stores the minimum and maximum measured temperature range for instant recall via the LCD display.
-
product
Infrared with Laser & Thermocouple Jack
412
The 412’s innovative design incorporates a Non-contact Infrared Thermometer to measure surface temperature with a Thermocouple Jack to measure internal temperature.
-
product
FD-11614, 16-Channel Temperature Input Device for FieldDAQ
785854-01
The FD-11614 measures up to 16 thermocouple channels. It features cold-junction compensation and open thermocouple detection with an LED indicator per channel to identify disconnected thermocouples. The FD-11614 has an ingress … protection rating up to IP67 (dust- and water-resistant), can operate in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 g vibration. The FD-11614 incorporates Time Sensitive Networking (TSN) and features an integrated network switch and built-in power circuitry for simple daisy chaining. You program the FD-11614 with NI-DAQmx, which automatically synchronizes multiple FieldDAQ™ devices. This device is ideal for test cell and outdoor environments.
-
product
Signal Isolators
Signal IsolatorsDatexel manufacture a large range of Signal Isolators. The DAT511 is a loop powered isolator with 3000 V galvanic isolation between the input and output. It is a 2 wire device so there is no external wiring. The DAT511H is similar but is Hart compatible. The DAT4035 is a universal input signal (Thermocouples, RTD's, mV, Volts, mA, resistance and potentiometers) conditioner with 2000 V isolation between the input and output and it is PC programmable. It is a 2 wire loop powered device. The DAT4135 is similar but it is a 4 wire device so it has the ability to boost the output or provide a voltage output.
-
product
Thermometer, 2 Channel, 0°C to +1767°C, 175 mm, 85 mm, 30 mm
72-7715
Compact handheld thermometer is ideal for a variety of industrial, residential, HVAC and equipment testing applications. It accepts a wide variety of industry standard thermocouple probes and features internal data logging of up to 100 records. Dual inputs allow simultaneous measurement of two separate zones with independent readout or differential (T1-T2) display
-
product
Data Logging Kit
ThermoVault
Oven Temperature Profiling kit. Comes with TC101A Thermocouple based Temperature Data Logger with screw terminal, Thermally insulated enclosure, and Type K thermocouple probe.
-
product
Multimeter, Tester, LCR
7 digit resolution.Highly sensitive DCV and resistance measurements with 100 pV and 100 nOhm.1.3 nV eff , 8 nV peak-peak noise performance.Built-in low-noise 2-channel scanner.Direct SPRT, RTD , thermistor and thermocouple temperature measurement with 0.003 C accuracy.3 built-in low-power, dry-circuit test resistance functions.GPIB and RS232 interface.
-
product
Thermocouple Interface Amplifiers
Analog Devices offers specialized precision thermocouple interface amplifiers that provide a simple and effective solution for measuring thermocouple temperatures. With features such as integrated cold junction compensation and a high gain precision instrumentation amplifier, these thermocouple amplifiers provide a complete signal conditioning system in one IC package. ADI’s thermocouple amplifiers are suitable for use in diverse environments to measure a wide range of temperatures. These products will save you in cost, space, and unnecessary circuit design across a broad range of applications and industries.
-
product
Terminal Block For 34921A And L4421A Multiplexer
34921T
Offers a built-in thermocouple reference junction that helps minimize errors due to thermal offset
-
product
Thermocouple Thermometer, Dual Input / Analog Output
871A
Industry''s leading handheld thermometers that feature analog outputs for use with chart recorders or computer I/O cards, the 870 series has dual thermocouple inputs and respective linear analog outputs which produce 1mV/C or 5/9 mV/F in the 200 ranges and .1mV/C or 5/90 mV/F in the other ranges. The Model 871A uses Type K thermocouples to measure a temperature range from -40 to 1999F (-40 to 1370C) and the Model 872A uses type J thermocouples to measure from -40 to 1400F (-40 to 760C).
-
product
FlashCheck TCT
Digital Thermocouple Thermometer Kit is an expanded range, handheld instrument used by food service professionals and quality control inspectors to verify temperatures of foods and equipment throughout preparation, storage, and handling of food. This digital thermometer kit gives you maximum durability and versatility that can be used in a variety of situations.
-
product
MSXB 042
MSXB 042
The MSXB 042 Analog Termination Board allows quick and secure connection of discrete wires to the iDSC 1816 Board. MSXB 042 includes locations to install voltage divider resistors and 0-20mA termination resistors, as well as a Cold Junction Compensation (CJC) circuit for thermocouple applications.
-
product
Brake Fluid Boiling Point Tester
6513C
Peaceful Thriving Enterprise Co Ltd
This tester can measure the boil point of the brake fluid. It can measure the wet boiling temperature of the brake fluid for technician as a reference for maintenance. It can be the reference when technician is going to change the brake fluid. Besides the brake fluid, user can also measure the temperature of other fluid by connecting the tester with K-type thermocouple.
-
product
Band-On Telemetry System
Advanced Telemetrics International
The ATi Band-On Telemetry System transmits real-time sensor data from a rotating shaft while the system is running. The system consists of one or more rotating signal conditioner/ transmitter modules with battery pack and a stationary receiver. Rotating transmitters are available to interface with most any type of sensor including strain gages, thermocouples, thermistors, RTDs and accelerometers.
-
product
Temperature Input Device
The Temperature Input Device is a thermocouple measurement device featuring InstantDAQ technology. InstantDAQ technology includes built-in software for viewing and logging data that automatically loads when you plug in the device, so you can instantly take temperature measurements with your PC. You can connect the Temperature Input Device to any USB port to use your PC as a display and monitor data in real time. The device is compatible with J, K, R, S, T, N, E, and B thermocouples.The Temperature Input Device includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
Engine Speed Control and Measurement (Test Set A)
MS 1100
*Checks the parameters such as current, voltage, speed, and turbine gas temperature of 804E and 811 engines Portable instrument*Testing of Automatic engine control system and after burner control system*Simulates the temperature signal derived from the engine TGT (Temperature Gas Turbine) thermocouples*Simulates the speed signal, NL (low pressure shaft speed signal) drive from the L.P shaft Probe*Indicates the current signal to the FCU solenoid derived from the engine control amplifier*Measure the TGT and NL simulated signal at static position*Measure the signal produced by the engine TGT thermocouples*Measure the NL signal produced by the LP shaft*Measure the NH (High-pressure shaft speed) signal produced by HP shaft*Indicates the solenoid current, produced by the engine control amplifier*Indicates the solenoid voltage, produced by the engine control amplifier*Used to test engine in both static and dynamic states
-
product
High Current Transformers
High Current Transformer is designed to elevate and check the temperature of the conductors at high current levels, in order to simulate the current loading conditions found in electrical circuits. High Current Transformer is designed as an open type transformer that uses the test object as its secondary coil or has 1 or 2-turn self secondary winding. The conductors cores' temperature depends on the short-circuit high current caused by the test object. According to the current going through the test object, the test temperature of the conductor will change. The loop temperature is measured by a thermocouple probe which is directly connected to conductor.
-
product
Thermostation
VT-96
Thermal station VT-96 is intended for building data collection systems (distributed and remote) from thermocouple temperature sensors. The interfaces allow you to easily and quickly connect the VT-96 to a remote (via ETHERNET) or nearby computer (via USB). The integrated WEB-page provides a convenient way to check the communication with the unit and its functioning, and the standard VXIplug & play drivers reduce the costs of integrating the unit into the system and developing application software. Multiple thermostats easily integrate and synchronize with each other and other VXI instruments via a dedicated Trigger Bus.
-
product
Thermocouple Vacuum Gauge Tubes
DV-6 Series for Medium Vacuum
Teledyne Hastings, manufacturer of the original DV-4, DV-5, and DV-6 thermocouple vacuum gauge tubes, produces vacuum measurement equipment with exceptional stability, accuracy, and reliability under the most demanding conditions.The Teledyne Hastings’ DV-6 series thermocouple vacuum gauge tube acts as a localized sensor which is then paired with a selection of meters or controllers to provide reliable, cost-effective measurements in diverse applications. The robust sensor gauge tube is easily installed into vacuum systems and when properly excited, generates a thermoelectric voltage to provide a vacuum pressure measurement based on gas density. The DV-6 thermocouple vacuum gauge tube fully compensates for temperature and rate of temperature change.Thermocouple gauge tubes are calibrated on vacuum systems that contain N2 or Air, but can be used with other gases. Additionally, thermocouple gauges and their controllers can be recalibrated when a replacement thermocouple gauge tube is installed, following instructions in the manual. However, our DB-20 reference tube is available to confirm meter/controller performance. A complete line of installation accessories are also available to simplify the integration of our thermocouple gauge tubes into a variety of vacuum systems. Our goal is to provide “one less thing to worry about”, when performance matters! With a wide range of meter, fitting, relay and output options, the DV-6 series provides a reliable pressure measurement in numerous industries and applications.
