Filter Results By:
Products
Applications
Manufacturers
-
product
Cable Tester
FST-500 High Voltage Cable Tester is a modular and customizable cable tester that can be easily adapted to various cable test or cable harness test applications. The electronics is based on Finero’s rugged industrial grade FST range of standard test equipment. All set and measured values are shown on alphanumeric display, additionally there is an analog panel meter for output voltage. Other cable paramerter like L, C and R can also be tested by using optional test and measurement equipment. The tester can be ordered with a build in PC and it can be used in conjunction with Finero’s Quality Control software.
-
product
CableEye® HV-Rated QuickMount™ Housing for CAMI Connector Boards
CBH2
CAMI Research Inc. (Acton, MA) has released a High-Voltage (HV)-rated QuickMount housing (CBH2) for its CableEye® automation-ready, cable and wire harness testing systems. As a free-standing, quick-release board fixture, it allows users to connect CAMI’s test interface boards to the 64-pin headers of any expansion module - even at some distance. The housing may be used with any CableEye model and is rated to 2100 Vdc / 1500 Vac.
-
product
Pin-Mapping for Custom Connectors, Test Fixtures, UUTs | Cable & Harness Testers
PinMap™
Check out this fast and super-easy pin-mapping process enabled by our optional CableEye® PinMap™ software. Map as fast as you can move the probe from one pin to the next. Use on your custom connectors, test fixtures, specially-built connector panels, or pigtail adapters to your CableEye tester.
-
product
Systems Integration for Circuit Card Assembly
Teledyne Advanced Electronic Solutions integrates CCAs and other sub-assemblies, cables and fabricated parts into system modules shipped directly to customers for integration into their products.- Box Build: custom built to order system solutions- High complexity box assemblies and subsystems- High frequency RF box assemblies and subsystems- Full functional RF testing up to 26 GHz (K band)- Multi-level systems integration – build and test modules and CCAs and integrate into higher level assemblies- Custom cell design for customer subsystems- Special bonding processes including thermal management and vibration- Robust torque and FOD control programs- System level testing including functional, vibration and thermal- Complex harness fabrication and integration- Fiber-Optic and RF waveguide integration and testing- Large system capacity in excess of 200 lbs.- Configure to order – Integrate different options, firmware, configurations, etc across a single order as required
-
product
Portable Tester
ECAD System 2002
The ECAD System 2002 is a portable, ruggedized tester that can be used for troubleshooting and condition monitoring of installed circuits, cables and wiring harness. The ECAD tester is a combination of traditional electrical measurements, a database for storing test results, and data analysis software. This powerful combination allows a user to evaluate the condition of all circuit components in a logical and straightforward manner from one end of the circuit.
-
product
Test Management Software
Easy to use to minimal training. Our Test Management Software is powerful enough to accommodate all of your electrical and function testing requirements, whether testing a cable harness or fully equipped vehicle or aircraft.
-
product
Sea Water Immersion Test Device
Guangdong Bell Experiment Equipment Co.,Ltd
Sea Water Immersion Test Device Relevant standards requirement:Test Object: Battery storage pack or system.The test object connects all the wiring harness, connector and other parts according to the whole vehicle connection mode. Select one of the following two methods to operate test at the room temperature.Immerse the test objects (in the direction of real vehicle assembling) into 3.5% NaCl solution (mass fraction, simulated under normal temperature water composition) for 2 hours. The water depth is to be sufficient to completely submerge the test objects.Test objects according to GB/T4208-2017 part 14.2.7 test method and test process.
-
product
Software Development
In support of system, test and our tooling design, our software development team is ARC’s primary advantage in providing the superior performance in hardware (electrical), mechanical and software cohesiveness. The software team at ARC literally brings all of it together.Whether you want to leverage one of our standard platforms, such as TestCentre or harness the power of the process editor in our PVS software to build up your custom workflow, most customers are impacted by the power and scalability of our software solutions, without sometimes ever knowing the tremendous effort that goes into our software.Customization, whether you are needing work in LabVIEW, TestStand, C# or other development platforms, our team can deliver the perfect solution, tie the mechanical and electrical worlds together in coming up with your next solution.
-
product
Diesel Dynamometers
Heavy-duty toroidal water-brake or large eddy-current absorber, S-beam electronic torque transducer, high-flow manual (or optional electronic) engine load control, DYNOmite data-acquisition computer, rigid-frame engine test stand, wall (or stand) mounted control console, absorber to engine-block mounting adapter, heavy-duty input shaft, calibration arm, stainless-braided hoses, and full-function data wiring harness.
-
product
4/5 Pin Trailer Harness Checker / Towing Maintenance Kit
#8026
Innovative Products of America
Test, clean and restore 4/5 pin trailer connections. Tester will verify tow vehicle is sending proper signal to the connector, while cleaning tool removes corrosion and verifies proper pin size on both male and female truck/trailer plugs. For use with 4/5 flat connectors. Patented. Extends harness life Great preventative maintenance tool Promotes safety and limits road hazardsKit Includes: #7866: 4/5 Pin Trailer Harness Checker, #8021: 4/5 Pin Cleaner, and #8030: 2 ml DeoxIT Cleaner
-
product
USB Type-C Test Fixture | CB26U | Cable Harness Tester
A leader in development of PC-based cable and wire harness, continuity, resistance and hipot test systems for over 20 years, CAMI offers the CableEye suite of products complete with accessories – including “connector boards”. The selection of these test fixture boards is constantly growing and is currently numbering over 60 – most of which are populated with ‘families’ of connectors. When pre-populated boards are used, the tester GUI automatically displays a graphic of the connectors under test.
-
product
Switch Probes
A switch probe is designed primarily for “presence/ electrical” test applications such as detecting the absence or presence of contacts within a wire harness connector. In this case, the switch probe provides electrical interconnection and verifies the connector has been manufactured properly. If contacts are missing or out of place, the part is rejected. If all the contacts are in place, the part is accepted and an electrical test is performed, verifying the electrical integrity of the connector and the wires within the harness.
-
product
Portable Meter Test Kit
UTEC 430
The UTEC 430 is the first Portable Meter Test Kit to support both the Radian Dytronic (RD) and the installed base of Radian Metronic (RM) reference standards. The ability to support both reference standards makes the 430 the ideal budgetary solution for traditional on-site meter testing using Phantom Load current sourcing. Do not let its compactness fool you, the UTEC 430 has three 30 Amp current output elements for performing single-phase or three-phase meter testing. When each element is combined using the optional open link cable harness, the UTEC 430 can source up to 90 Amps.
-
product
PCB Test Fixtures
ATE, ICT, semiautomatic & manual electronic test fixtures, PCB test fixtures, cable test fixture, wiring harness test fixtures, dedicated test fixtures, functional test fixtures, electronic test fixture programming. PADS Schematic capture, circuit board layout, PCB design prototype, solder paste stencils, X-Y coordinate data, B.O.M. maintenance, and manufacturing documentation, Gerber data.
-
product
Cable/Harness Tester
CR
As a wire harness tester, a cable tester, a continuity tester, a component tester, and a guided harness-assembly aid, the Easy-wire CR tester is versatile. The easy-wire CR features Windows based software that allows you to create custom graphics of your connectors and light LEDs to guide the harness assembly process. Test Points: 256-32,000, Test Current: 6.5 mA max
-
product
Hipot Wire Harness Testers
NX Hipot
* 50 to 1500VDC Hipot Testing* 50 to 1000VAC (optional) * 5Mohm to 1Gohm Insulation Resistance * Simple 4-button user interface * Tests for continuity and shorts * Tests a variety of components * Precision resistance measurements * Continuous high speed scanning for real time complete status information of harness assembly progress * Keyed security access and control * Built for rough industrial environments * 2 serial ports for connection to printers and scanners * Standalone operation * Uses a high capacity memory card * Available from 64 to 1024 test points * Networkable
-
product
Cable Harness Test System
Data Patterns has built high reliability Cable Harness Test Systems for large installations. These are primarily used in launch vehicle aircraft and missile level cable harness test validation. Installations with upto 20,000 lines test capability at a single location have been supplied by Data Patterns. Portable version capable handling of as small as 384 points have also been addressed.
-
product
High Voltage, Continuity & Hipot, Cable & Wire Harness Test Systems
CableEye HVX, HVX-21
Fast ● Simple ● Precise
Advanced wiring analyzer scans for continuity (opens, shorts), miswires, resistance, capacitance, components (resistors, diodes, LEDs, capacitors) dielectric breakdown, insulation resistance, intermittent connections
HVX (Item 829) 1500 Vdc, 1000 Vac
HVX-21 (Item 829A) 2100 Vdc, 1200 Vac
For diagnostic and Pass/Fail Testing — Permits expanded testing (compared to models in our low voltage product line) for insulation resistance (IRI) and dielectric breakdown (DWV).
All CableEye testers are suitable for production, fault diagnosis, QC (Quality Control), assembly, and prototyping of standard or custom cables. Each combines test, fault location, design, documentation, labeling, and database storage in one instrument. Tests can be performed on long cables (with or without connectors) or no cables (e.g. connectors, backplanes, PCBs, components).
Standard Features & Benefits:- USB certified, PC-based tester for a versatile, fast, robust system with long life-cycle.
- Multilingual, dynamic, graphic-rich display (netlist & wiring schematic) provides clarity and speeds diagnostics.
- 128 Test Points, expandable to 1024 providing flexibility as your product line changes.
- User-selectable voltage to each connection group in the cable simplifies an otherwise complex process, accelerating testing.
- Programmable Ramp Up, Ramp Down, Dwell Time (same as Test Time), Trip Current, and Trip Delay (same as Soak Time) adds versatility.
- Current leakage detected during HV test phase provides a measure of insulation resistance up to 1 GΩ (HVX) and 5 GΩ (HVX-21) - any leakage current exceeding a preset limit reveals the presence of moisture, flux, or other contamination on exposed contacts.
- Real-time screening for intermittent connections for pinpointing elusive faults and improving quality.
- Automation scripting in a simple, intuitive language allowing non-programmers to reduce operator error by automating repetitive steps.
- Pop-Up Work Instructions. choose the exact amount of detail, imagery, language and automation you need to ensure your work instructions and tests are carried out flawlessly.
- Flexible tolerancing: optionally define as percentages or absolute terms, as well as asymmetrically (e.g. +0%/-10%) for improved yields.
- Barcode-tracking & archival data-logging to achieve error-proof test process and improved traceability & productivity.
- Print PASS/FAIL labels, test reports (with or without color wiring schematics/netlists) and log reports to satisfy ISO9000 reporting requirements.
- Compatible with laptop and touchscreen PCs for fieldwork and rack/off-bench mounting.
Includes:
CB29 board set (Item 759) for bare wire connections; comprehensive PC software with Database of >200 standard cables; 2 yr Product Support Subscription comprising Warranty, free tech support, and free software upgrades.
Select Add-On Options:
Hardware: 128-point Expansion Modules (attach to base); 4-Wire Kelvin Resistance Measurement, 1 mΩ at 1 A; Advanced Measurements; External Measurement Instrument Port (e.g. 10 GΩ Isolation at 100 V); Remote Control Connector for Deadman Switch; Environmental Sensor
Software: PinMap™ fixture editor, Connector Designer™ connector editor, or Autobuild™ guided assembly modules
camiresearch.com |@CAMI_CableEye |+1.978.266.2655 -
product
Accessories
Every Logic ships with a case, usb cable, wire harness and test clips. Get extra stuff here.
-
product
Ada Embedded Software Test Solution
VectorCAST/Ada
An integrated software test solution that significantly reduces the time, effort, and cost associated with testing Ada software components necessary for validating safety- and mission-critical embedded systems. VectorCAST/Ada parses your source code and invokes code generators to automatically create the test code (stubs and drivers) required to construct a complete, executable test harness.
-
product
Wire Harness Tester
NX Pro
The Dynalab NX Pro Wire Harness Tester is a low-cost, feature-packed, stand-alone continuity tester with a maximum capability of 512 test points. The flexibility of the NX System allows each program to perform multiple tests, display custom messages or sounds, and analyze the results of a test or an input to "decide" which operation to perform next. The NX Pro Tester has 1.3Mb memory capacity for program storage and is compatible with Printers, Scanners, and all other Dynalab NX System accessories.
-
product
Interior Wiring Testing
With automotive interior designs becoming more luxurious, cabin space features such as ambient lighting and seat / steering wheel controls have increased the demand for interior wiring testing. Jackmark Engineering has years of experience supplying test equipment for instrument panel manufacturers and have increased their portfolio to include all aspects of interior wire harness testing.
-
product
Handheld Wiring Analyzer
HT-128+
Reduce your wire harness assembly and installation difficulties now. The NEXU HT-128+ test platform provides a valuable tool for multi-point wiring continuity analysis. Our versatile, lightweight, handheld unit can serve your wiring test and maintenance needs from harness layout to product field support. The HT-128+ performs testing and troubleshooting, automated ring-out, directed assembly plus other features to resolve wiring issues quickly to achieve increased product availability!
-
product
Automatic High Voltage Wire Harness Testers
Automatic high voltage wire harness testers are used in a variety of industries, such as aerospace and defence through to rail, and are used to test any equipment which contains a high number of electrical wires, or active components ensuring these pass specified test criteria at the sub-assembly and final stages of construction. These systems ensure the wiring and components are 100% compliant and undamaged, recording every test measurement and aiding diagnosis of detected faults.
-
product
DC Insulation Testing
Weshine Electric Manufacturing Co., Ltd
Cable harness tester is used for test and measure wire cable harness,wire harness, like as : auto cable, audio cable, power cable, network cable, telephone cable, USD cable, HDMI cable,video cable, etc. .
-
product
7 Spade Pin Circuit Tester / Maintenance Kit
#8028
Innovative Products of America
Test, clean and restore 7 spade pin connections.The tester will verify that the tow vehicle is sending proper signal to the connector, while accompanying cleaning tools will remove corrosion, and verify proper pin size on both male and female truck/trailer plugs. For use with 7 spade connectors. Quickly tests, cleans and repairs truck and trailer connectors Extends harness life Great preventative maintenance tool Promotes safety and limits road hazardPatentedKit Includes: #7893: 7 Spade Pin Circuit Tester, #8023: Connector Cleaners, and #8030: 2 ml DeoxIT Cleaner
-
product
Cable and Harness Tester
CHT
The Cable and Harness Tester (CHT) provides multiple testing capabilities for up to 300 connector/harness test points. Test capabilities include DC Insulation Resistance (IR), DC and AC Dielectric Withstanding Voltage (DWV), and 2-Wire and 4-Wire Continuity.
-
product
6 Pin Round Pin Tester / Maintenance Kit
#8027
Innovative Products of America
Test, clean and restore 6 round pin trailer connections. Included tester will verify tow vehicle is sending proper signal to the connector, while cleaning tools remove corrosion and verify proper pin size on both male and female truck/trailer plugs. For use with 6 round connectors. Quickly tests, cleans and repairs truck and trailer connectors Extends harness life Great preventative maintenance tool Promotes safety and limits road hazardsPatentedKit Includes: #7897: 6 Pin Round Pin Tester, #8022: 6 Round Connector Cleaners, and #8030: 2 ml DeoxIT Cleaner
-
product
Modular Test System
A modular test system, RTS (real time scanner) provides instant test results with minimal interface cables to check wiring during installation.It tests wire harnesses in real time using our micro switching technology, reducing the need for high cost interface cables by around 90%. an innovative best-in-class solution for FAL testing, RTS also offers many benefits for wire harness and sub-assembly manufacturers.
-
product
Threaded Probes Designed for Connector and Harness Test
Equip-Test Threaded Probes Designed for Connector and Harness Test
