Filter Results By:
Products
Applications
Manufacturers
TTL
Transistor–transistor logic.
-
product
PMAC Input/Output (IO) Modules
PMAC Input/ output (I/O) modules offer a wide range of analog or digital IO including AC, DC, TTL and analog.
-
product
3.5" Embedded SBC With AMD LX800, Dual LANs, 4 COM, 4 USB 2.0 And VGA/LVDS/TTL
SBC84622
The SBC84622 supports an onboard low power AMD LX800 500 MHz processor with the AMD Geode CS5536 chipset. The flexible display function is supported by integrated graphics controller which allows users to configure both CRT and LVDS LCD or CRT and TTL LCD as simultaneous mode. Onboard one DDR SODIMM supports up to 1GB of system memory. Having such compact design with fanless operation, the SBC84622 can be applied in widely embedded and automation applications such as industrial automation, automation control, telecommunication, and process control.
-
product
PCI 32 Channel TTL Digital Interface
8010
The 8010 PCI digital I/O interface provides 32 channels of buffered drive digital I/O, which can be utilized for PC based control and automation of equipment including sensors, switches, security control systems, and other industrial automation systems. 10K pull-up resistors are included. Optional values are available.
-
product
Reconfigurable FPGA w/ AD/DA & Digital I/O PCIe Mini Card
TMPE627
The TMPE627 is a standard full PCI Express Mini Card, providing a user programmable Xilinx Artix-7 7A50T FPGA. The TMPE627 provides 14 ESD-protected 5 V-tolerant TTL lines. All I/O lines are individually programmable as input or output. TTL I/O lines can be set to high, low, or tristate. Each TTL I/O line has a pull-resistor to a common programmable pull-up voltage that can be set so +3.3 V, +5 V and GND.
-
product
Imaging Scanning Monochromator
H1034
HORIBA Scientific OEM has developed a high-throughput imaging scanning monochromator based on an aberration-corrected concave holographic grating with low stray light and high efficiency. This proprietary layout with single optics design is ideal for imaging for low-light applications. It features a 3-position external filter wheel, TTL drive electronics, 4-phase stepper motor and associated worm/gear 90:1 ratio mechanism, encoded, aligned and focused at factory.
-
product
PCI Synthesizer
SYNTH300 Series
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.
-
product
FPGA PXI Card with 80 TTL Differential Channels Module
GX3609
The GX3609 is a 3U PXI FPGA card with 80 TTL differential channels. The GX3609 is comprised of a GX3500 FPGA card and the GX3509, 80 channel, differential TTL expansion card.
-
product
Pulse Generation Measurement Board
MS 1806
*TTL Pulse measurement channels (Timers / Counters) 18 Channels*TTL Pulse Generation - 12 Channels*The Pulse Generation Frequency from 10Hz to 40MHz*The no. of pulses controlled from 1 to 255 pulses*All Channels are compatible with 5V TTL / CMOS*All the pulse input and the output signals driven through Pin Driver*Standard ISA Bus Interface*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
product
24 TTL Channels, Enhanced, Programmable I/O
TL2
Function module TL2 provides 24 channels of TTL/CMOS transceiver functionality as either inputs or outputs. The transistor-transistor logic (TTL) employs transmitters with multiple emitters in gates having more than one input. TTL offers high switching speed and relative immunity to noisy systems. CMOS sensors provide image sensing technology by converting light waves into signals that are small bursts of current. These waves can be light or other electromagnetic radiation.
-
product
Ethernet to Relay Minibox™
Model 8064
* Model 8064-11 provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.*Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully VXI-11 compliant.* Easy configuration with any web browser.* Includes 50-pin mating connector for solder connections.* Optional 1 'U' high Rack Mounting Kits hold one or two 8064s.* Optional terminal board and terminal strip for easy connections without soldering. See the Ethernet Accessory page.
-
product
Digital I/O Card
Axiomtek's digital I/O cards feature TTL I/O, isolated I/O, relay output, and timer/counter, and supports high-density on a single board, making them specifically suitable for factory automation, industrial ON/OFF control and switch status sensing.
-
product
Low Profile Solid State Relays, Utilizing MIL-PRF-28750 Test Methods
Series KD and LD
Your product description goes here.Series KD and LD solid-state relays utilize MIL-PRF-28750 test methods and are packaged in low-profile hermetically sealed cases. They feature fully floating power FET output technology. Options include short-circuit and current overload protection plus a status output line. Switch status returns the true status of the output switch and is optically isolated from the load.MSL 1KD & LD relays are controlled with 15mAdc/3.8Vdc (TTL), and 1mAdc/0.3Vdc (CMOS).Available options include:KD00CK 5Adc, 60Vdc Load KD02CK 5Adc, 60Vdc Load; with switch statusKD20CK 5Adc, 60Vdc Load; with short circuit protectionKD22CK 5Adc, 60Vdc Load; short circuit protection & switch statusLD00CM 10Adc (5Adc without heat sink), 60Vdc LoadLD02CM 10Adc (5Adc without heat sink), 60Vdc Load; with switch statusLD20CM 10Adc (5Adc without heat sink), 60Vdc Load; with short circuit protectionLD22CM 10Adc (5Adc without heat sink), 60Vdc Load; short circuit protection & switch status
-
product
Digital I.O Module with 64 TTL Channels
IO203
This I/O module is a dedicated digital I/O module providing a total of 64 TTL channels. The TTL transceivers are TTL and CMOS/TTL compatible and can also set to be CMOS compliant by the Setup driver block. Each of the 64 channels can individually be programmed as input or output. The 64 channels are further separated into two groups of 32 channels each.
-
product
PXI H. Density Digital I/O Module 32 Bit O/C
40-410-002
The 40-410 range of Digital I/O Modules are suitable for operating external devices, such as heavy duty relays (power, RF and high voltage types), solenoids, lamps, or for interfacing with external logic such as a programmable instrument with a BCD interface. Two choices of output drive are available: TTL for interacting with external logic and Open Collector Transistor for operating external devices with voltages to 50VDC and currents to 500mA.
-
product
GPIB Parallel Interface
Model 4823B
* Provides 56 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Available with DIN connector on circuit side for piggyback mounting.
-
product
Length Gauges For Measuring Stations And Multi-gauging Fixtures
METRO series
*High repeatability*Very high system accuracy of down to: ±0.2 µm*Ball-bearing-guided and zero-backlash plunger*Variant with reduced gauging force*Very long measuring ranges of up to 100 mm*Interfaces: 1 VPP, TTL, 11 µAPP*Protection rating of up to IP67
-
product
High-Power Noise Sources
These modules not only contain the noise diode circuitry, but also gain stages to boost the output power. While lower frequencies (under 2 GHz) are most common, Mercury produces powerful amplified noise modules up to 18 GHz. Noise modules are available in coaxial, surface mount and pin type construction. TTL control options are available.
-
product
IO Expander
AD16x2DA16x8-125ETH
The IO Expander is an additional module to provide more input and output capabilities to the AD16x2DA16x8-125ETH. Via high speed link it connects 8 TTL inputs, 16 TTL outputs, 8 SPDT RF switches, and a GPS module.
-
product
8 Channel LE Discriminator
NIMbox NDL8
NDL8 - 8 channel LE discriminator with 10 programmable NIM or TTL I/O ports and 2 TTL I/O ports
-
product
Serial Digital Interface
Model 2363
* Provides 48 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes or data strings.* RS-232 and RS-485 Serial IO.* 1 U high rack mount kit mounts one or two 2363s* Includes US 115 VAC Power Adapter
-
product
12-bit, 200KHz, 16SE/8DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3110-16
The APCI-3110 is a 12-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3110, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
product
Signal Conversion Box for Linear Gauge Sensor
DG-0010/0020
This is a signal conversion box to convert 2-phase signals (TTL) from the linear gauge sensor GS/BS series into open - collector (DG-0010) or line driver (DG-0020) .This conversion box allows direct connection with the PLC *. It can also be transmitted over long distances.
-
product
Diode Lasers
6-Watt Blue Engraving Laser
Advanced Photonic Sciences LLC
Can be used in laser engraving, marking, and cutting applications. Process wood, plastics, metals, anodized aluminum, stone, tile, and other materials. The adjustable spot can be adapted to the needed distance from laser to the material. The spot, with a size of <100 μm, creates very fine engravings and sharp cutting edges. The built-in driver accepts TTL and analog signals for power adjustments. The laser can be controlled between 0% and 100% of output power. It comes preset and needs only a power supply and a signal source.
-
product
High-Frequency Switch
VCH-604
High-Frequency Switch VCH-604 is designed for switching high-frequency (1 – 100 MHz) and pulse TTL signals. VCH-604 contains two groups of channels; each group has 25 inputs and 2 outputs. VCH-604 can be controlled from PC via GPIB and RS-232 interfaces or directly from front panel.
-
product
Serial Parallel Interface
Model 2313
* Provides 128 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Separate headers for RS-232 and RS-485 signals. * Optional 2313 Flat Ribbon Cables mount DE-9 male or female connectors on the rear panel. * Optional Relay Driver boards with 64 or 128 Relay Drivers.
-
product
RS232 / RS485 / RS422 / TTL Serial Converters
Rated to perform at temperatures between -40°F and 185°F (-40°C and 85°C), our rugged industrial-grade RS232 / RS485 / RS422 / TTL serial converters are almost indestructible. These industrial-grade serial converter products support multi-drop RS485 / RS422 networks and come with 600W surge protection, 15KV ESD protection, selectable end-of-line terminators, and optional 2500V opto-isolation circuitry, which ensure crisp data signals without interference for all types of installations.
-
product
IC-3173, 2.20 GHz Intel Core i7 Dual-Core Processor, 4-GigE Port, 2-USB 3.0 Port Industrial Controller
784965-01
The IC‑3173 is a high-performance, fanless industrial controller for developers who require a high level of processing power and connectivity for automation and control applications in extreme environments. The IC‑3173 provides connectivity for communication and synchronization to EtherCAT and Ethernet CompactRIO chassis, EtherCAT motion drives, GigE Vision and USB3 Vision cameras, and other automation equipment. In addition, this controller has onboard isolated, TTL, and differential digital I/O, so it can perform synchronization and control tasks without additional tethered I/O.
-
-
product
32x ADC, 16x/0x DAC & 8x Digital I/O PMC Module
TPMC533
The TPMC533 is a standard single-wide PCI Mezzanine Card (PMC) compatible module providing 32 channels of simultaneous sampling true differential bipolar 16bit analog input, 16 or no channels of simultaneous update single-ended unipolar/bipolar 16bit analog output and 8 channels of tri-state 5V-tolerant TTL digital input/output. All signals are accessible through a HDRA100 type front I/O connector.
-
product
Digital I/O
ADLINK digital I/O cards feature TTL I/O, isolated I/O, relay output, and timer/counter, and supports up to 256-CH high-density on a single board, making them suitable for I/O status monitoring and ON/OFF control applications.
