Filter Results By:
Products
Applications
Manufacturers
TCP/IP
Protocol suite governing internet communication.
-
product
LAN⇔RS-232C(2ports) Converter
SI-60X
SI-60X is an interface converter that converts 2 serial ports of RS-232C devices to Ethernet LAN at 10Base-T/100Base-TX. The built-in Lantronix WiPort® NR on the LAN interface converts RS-232C data into LAN protocol (TCP/IP). The device supports 35mm DIN rail and the wide range of operating temperature. The small housing ensures ease of use for FA applications, public facility and medical institution as a communication device server.
-
product
Evaluation Board
emPower
SEGGER Microcontroller GmbH & Co. KG
The emPower eval board provides a comprehensive set of SEGGER's middleware products, accelerating the start of any embedded project. SEGGER's embOS real-time operating system is at the heart of the evaluation. Furthermore, evaluation versions of the file system emFile, graphics library emWin, emUSB Host & Device, and TCP/IP stack embOS/IP (including web server demo) enable full use of the available emPower peripherals. emPower also features a J-Link OB, an on-board version of SEGGER's market-leading debug probe J-Link, which includes drag & drop programming and COM-Port support. There are three expansion interfaces to easily connect additional modules. Each connector provides I2C, SPI, UART, GPIO/timer, analog input and power. A display adapter connector enables the connection of small TFT displays. The emPower board is powered by USB only. Current consumption drawn strongly depends on the application and connected peripherals. Idle consumption is approx. 85 mA.
-
product
TCP/IP CCTV Equipment
BitNet
BitNet is a 4-bit digital to Ethernet converter that enables up to four, volt-free contact inputs to be transmitted on to a local area network (LAN). Each input is assigned a unique number to identify any contact that has closed or opened. A maximum of 16 BitNets may coexist on the LAN which will facilitate up to 64 volt-free inputs.
-
product
Modbus Data Acquisition
The Datexel range of Data Acquisition equipment includes Modbus RTU Masters and Slaves, Modbus Input, Modbus Output Modules, Modbus Isolation Modules and Modbus Repeaters. The range also includes converters (RS485, USB, RS232, RS422, TCP-IP). By combining these units with the DAT3000 and DAT10000 series a complete solution for your Data Acquisition can be found from Datexel. The DAT9550 is a remote Modbus display unit that can be programmed to accept data from Modbus slaves or masters such as a PLC or the DAT9000 range of Modbus controllers.
-
product
RS232 RS485 RS422 Serial To Ethernet Modbus Converters / Device Servers
In the past two decades, legacy serial communication protocols such as Modbus have merged rapidly with modern TCP/IP communication, yielding benefits including widely available infrastructures and greater distance, reliability, and flexibility. CommFront offers a range of industry-proven, easy-to-use serial to Ethernet converters and device servers, both hardware and software types. The applications of our serial to Ethernet converters include acting as a device server or a Modbus RTU/ASCII to Modbus TCP protocol converter; extending serial ( RS232 / RS485 / RS422 / TTL) communication distance over Ethernet network; controlling serial devices from remote Modbus TCP software or Modbus RTU master via Ethernet network; making a wide variety of M2M communication applications possible by enabling client access independent of any operating system or proprietary protocol; and converting conventional serial data network into TCP/IP network, etc.
-
product
Ethernet To Parallel Digital Interface Boards
ICS's Ethernet Parallel Digital Interface boards provide the user with a wide range of IO signals that can be user configured to match virtually any application. These Ethernet boards are available with high power relay driver boards and with optional firmware designed to simplify switching applications. The 80x3 boards have high-power TTL signals that can sink 48 mA and source 24 mA. Pullup resistors make it easy to interface with CMOS logic and to sense contact closures. User configures data byte direction and polarity. The 80x3 boards are VXI-11 compliant for operation with NI or Agilent VISA, LabVIEW and VEE and support raw socket connections. The new 8113 board is a CMOS close of the 8013 board with user set 3.3 or 5 V logic levels. Pinouts and command set is the same as the 8013 board. The 8113 communicates with TCP/IP(Raw Socket) protocoland and also has a RS-232 Serrial Port. All boards are designed for mounting against the rear panel or inside a chassis and use our Ethernet Wiring Kit for easy connection to a Ethernet Connector on the rear panel.
-
product
Modbus PLC Simulator
This protocol simulator started one weekend as a test program while developing a SCADA/HMI with modbus RTU and TCP/IP and afterward came in useful testing an embedded gnu-Linux device too. It has worked so well for me, I decided to put a nice GUI onto it and release it for free. The modbus protocol, also called open-mbus is implemented in many process control and monitoring devices, while most SCADA or HMI systems have a driver.
-
product
Ethernet-GPIB-USB to Modbus RTU Interface
Model 9009
* All interfaces provide full control of the Modbus RTU slave devices.* Ethernet port supports VXI-11, raw socket and Modbus TCP/IP to Modbus RTU conversion. * GPIB port works with any IEEE-488.2 compatible GPIB controller.* USB port uses Microsoft supplied driver to prevent operating system change problems.* The 9009 uses a simple command set that is accessible from any port.* Controllable with Windows PC programs like C, Visual Basic, LabVIEW, VEE, etc that make VISA or SICL calls. Works with Agilent, NI and Kikisui VISA libraries* Controllable from MAC/UNIX/LINUX and similar computers with RPC calls.* Ethernet interface protocol is fully VXI-11 compliant and does not require special PC drivers.* Internal webserver with sample Modbus device control pages for Watlow F4, F4T and EZ-Zone Controllers.* OEM oriented board designed for integration inside the user's system with only one cable. On board regulator works with 5 to 15 Vdc power.* Support programs Include ICS's VXI-11 and VISA keyboard control programs and a NTML page utility for uploading your customer webpages.
-
product
Ruggedized Small-Size Telemetry System, Requiring Laptop for Display and Control
LS-84-EC
The Lumistar LS-84-EC “Economy Chassis” Telemetry System offers a low cost, high performance COTS solution for a portable quick look ground/remote/airborne station. The unit has a built-in computer running Windows 10 (WIN 7 option) for stand-alonecontrol or can be controlled remotely over TCP/IP. Using Lumistar’s PCI-based or modular line of telemetry products, acomplete telemetry ground station can be configured in a very small space. Functions such as RF reception, demodulation, bitsynchronization, simulation, frame sync, decom, data archive and real-time display can all be handled in this unit. Data can bearchived on an internal solid state drive or external serial ATA or USB 2.0 drive. A laptop using a network connection providesremote control and access to real-time displays. The I/O connections from individual PCI cards are hardwired internally within the chassis, thus allowing a bulkhead mount configuration on the rear panel of the chassis.
-
product
Multibus Development and Test Tool for ECUs and Networks
CANoe
The versatile software tool for development, testing and analysis of ECUs and entire networks. Bus systems: CAN, CAN FD, LIN, MOST, FlexRay, Ethernet, WLAN, Car2x ITS G5, AFDX, J1708, ARINC429 > Protocols: TCP/IP, SOME/IP, CANopen, J1939, ISO 11783, J1587, MCnet, GMLAN, K-Line, CANaerospace and ARINC 825. Others upon request.
-
product
Two-Way Time Transfer (SWSTFT) Satellite Time and Ranting Equipment (SATRE)
TWSTFT
- 1 – 3 receiver channels- Automated measurements- Operates unmanned, 24 / 7- Remote control over TCP/IP- Data transfer via TWSTFT link from remote site- Sub-nanosecond precision TWSTFT with real time results- Internal measurement database for the last three months on a one minute basis
-
product
GPIB-ENET/1000, Ethernet GPIB Instrument Control Device
781630-07
Ethernet GPIB Instrument Control Device - The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
Modbus Stack
softMOD
SoftMOD is the industry-standard Modbus protocol stack for industrial automation and building management. SoftMOD supports both Modbus RTU (Remote Terminal unit) and Modbus TCP/IP (Transmission Control Protocol) as well both client and server modes.
-
product
Industrial GSM MODEM
QSM-26
Infinite Industrial Informatics Lt
QSM-26 is a DIN rail mount GSM/GPRS MODEM. The unit has a built in Quad Band (850/900/1800/1900MHz) Sierra Wireless Q2687 modem, 2 digital inputs, 2 power relay outputs and a serial RS-232 port. Special AT commands are implemented for TCP/IP based communications.
-
product
LAN⇔RS-232C Conversion
SI-60F
SI-60F is an interface converter to connect factory automation equipment and analyzers, which only have the RS-232C serial communication port, to LAN. The built-in Lantronix Xport® on the LAN interface converts RS-232C data into LAN protocol (TCP/IP). It is the environment-friendly design, such as low power consumption from DC5V and compact body (resource saving).
-
product
Fire, Gas & Intruder Controllers & Alarms
MultiSafe-MX
Teledyne Gas & Flame Detection
The MultiSafe-MX system is intended for the protection of high hazard, high risk plant and facilities.The MultiSafe-MX is certified, by European laboratories, to comply with the applicable regulations.The panel is composed of dedicated cards, installed in 19” racks which have their own “intelligence”, programmed for active/passive fire protection, gas detection, intruder alarm and logic functions. Moreover, the MultiSafe-MX can interact with supervisory and SCADA systems via Ethernet, TCP/IP or Modbus.The MultiSafe-MX interfaces with devices using either conventional and/or addressable module inputs and outputs. These modules are used to tailor the system to customer requirements.
-
product
Digital Quad-channel High-Frequency Lock-In Amplifier -
eLockIn 205
Being the top model eLockIn series, the eLockIn205/2 offers a very fast TCP/IP connection, ultra-fast DAC outputs of the measured signals and all signals supplied at BNC connectors.
-
product
GPIB-ENET/1000, Ethernet GPIB Instrument Control Device - Taiwan 110VAC
781630-11
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
XMC Gigabit Ethernet Boards
High-performance 1/10-Gigabit Ethernet interface solutions for real-time and COTS data streaming applications. XMC modules provide a rugged, embedded computing platform for high-speed data communication in defense, aerospace, and industrial systems. Implementing a TCP offload engine (TOE processor) fully in hardware relieves the CPU from TCP/IP overhead and frees it to perform other tasks.
-
product
TV Remote Service Analyzer
ITM-18
The TV signal analyzer ITM-18 is designed to measure the parameters of television signals of analog and digital (ITU-T J.83 Annex A/B/C standard, including DVB-C) television and transmit the measurement results via a local TCP/IP network to a remote PC. It is installed in the nodes of the cable network for continuous, automatic control of the parameters of the television signal.
-
product
Single Frequency CW 532 NM Laser up to 18W
EQUINOX
Equinox is a single frequency, 532 nm continuous wave laser designed for a range of scientific applications including pumping any Ti:Sapphire laser systems. It is engineered to meet the needs of experimentalists requiring high-performance systems with an emphasis on reliability, stability and ease of use. The laser incorporates pump diodes within the central unit and is fully automated with hands-free operation and control via ethernet, webpage and TCP/IP remote interface. This completely sealed system is inherently stable with low noise levels <0.05 % RMS and ultra-stable output powers with ±0.5 % stability. Equinox has options of high output power up to 18 W. Other major applications include mixing source, pump source for dye lasers and frequency doublers, optical tweezers, and biomedical imaging.
-
product
Ethernet Digital Interfaces
All of ICS's Ethernet Digital Interfaces are user configurable and let you transfer data as bits, bytes, as strings of bytes or transparently. All data lines are high power TTL outputs or floating inputs with pullup resistors for sensing CMOS signals or switch contacts. All interfaces conform to the IEEE-488.2 Standard, are VXI-11 compatible and/or support TCPIP Raw Socket protocol.
-
product
SpaceWire Monitors
This section details the 4Links range of high-performance test equipment that is used to monitor SpaceWire networks. These devices are attached to your SpaceWire systems and then can be accessed via Gigabit Ethernet, using the standard TCP/IP family of protocols, so that they can be controlled remotely (for instance, by partners collaborating on a mission).
-
product
Ethernet to Modbus RTU Interface
Model 9099
* Use Modbus TCP/IP, VXI-11, or Raw Sockets (Telnet) or to control Modbus RTU slave devices.* No special driver required which eliminates driver problems.* Controllable with Windows PC programs like C, Visual Basic, LabVIEW, VEE, etc that make VISA or SICL calls.* Controllable from MAC/UNIX/LINUX and similar computers with RPC calls.* Interfaces with PLCs or any Modbus TCP/IP Controller.* Fully VXI-11 compliant.* Works with Agilent, NI and Kikisui VISA libraries.* Internal webserver with sample Modbus device control pages for Watlow F4, F4T and EZ-Zone Controllers.* Network connectivity eliminates GPIB Bus Extension problems.* Allows multiple users to access the Modbus network or devices.* 9099 is a 2x to 5x faster than the 8099 and includes a new Modbus device control page.
-
product
GPIB-ENET/1000, Ethernet GPIB Instrument Control Device - Korea 220VAC
781630-09
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
CAN/Ethernet Gateway
CAN-ETH
CAN-ETH is a CAN to Ethernet gateway specifically designed to interface CAN networks with TCP/IP networks.
-
product
Densigrader: Dynamic Weight Sorter
The Densigrader: Dynamic Weight Sorter is made for on-line mass/density measurements and sorting of green lumber prior to drying. The accurate mass and optional volumetric measurements provide an increase in grade recovery and kiln productivity. Its small footprint fits easily into most transverse, lugged transfer chains. System employs either RS232 or TCP/IP protocols to hand off data to sorting PLC.
-
product
GPIB-ENET/1000, Ethernet GPIB Instrument Control Device - North America 240VAC
781630-05
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
Battery Monitoring System
IPQMS-C64
The iPQMS is the premier battery monitoring system in Eagle Eye's IBwatch-Series. It ensures backup power systems are optimally maintained in large-scale environments. The iPQMS is the main processing unit that measures up to 448 jars (or 448 cells) utilizing up to seven Relaying Units (RU). Each RU connects up to 64 jars (or 64 cells) and captures data from these batteries and sends it to the MPU in real-time. The iPQMS can be used over a private network via TCP/IP, or locally with RS-232. Networked systems can utilize SMS/Email alerts during an alarm outbreak. If you do not wish to use our Battery Management Software, Modbus protocol is available for third-party integration. Flexible expanding solutions allow multiple iPQMS units to monitor all your systems in real-time.
-
product
Ethernet Digital Interfaces
Model 8063
All of ICS's Ethernet Digital Interfaces are user configurable and let you transfer data as bits, bytes, as strings of bytes or transparently. All data lines are high power TTL outputs or floating inputs with pullup resistors for sensing CMOS signals or switch contacts. All interfaces conform to the IEEE-488.2 Standard, are VXI-11 compatible and/or support TCPIP Raw Socket protocol.
