Filter Results By:
Products
Applications
Manufacturers
Strain Gauges
measure of displaced surface elements.
See Also: Strain Gages, Strain Gage Amplifiers, Strain Gage Signal Conditioners
-
product
PXI Strain Gauge Simulator Module 6-Channel, 2k
40-265-306
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 2kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
product
PXI Strain Gauge Simulator Module 4-Channel, 3k
40-265-104
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 4-channel, 3kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
product
PCI Strain Gauge Simulator Card, 4-Channel, 1k
50-265-204
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
product
Digital Strain Gauge Sensor
ZET 7110
The ZET 7110 module is intended for measuring the relative deformation using primary transducers based on tension gauges. These may be either assembled tension gauges (force gauges, torque gauges), or detachable tension gauges connected using half-bridge or bridge mode.
-
product
Reusable ICP® Strain Gauge
This high-resolution dynamic alternative to bond foil strain gauges uses a quartz sensing element in a durable, titanium housing. It has 0.0006 microstrain resolution, 5 volt output, 100k Hz frequency response and 0.5 gram mass for lightweight test articles. The reusable sensor comes with a calibration certificate, attaches to the test specimen in 60 seconds and is removed in 10 seconds.
-
product
Strain Measurement Trainer Module
Unitech Scales And Measurements Pvt. Ltd
Strain Measurement Module comprises of Cantilever Beam bonded with four strain gauges,pan and weights upto 1Kg. Digital 3½ digit indicator module is supplied to read the microstrain.
-
product
Strainer-Recorder
To ensure reliable operation of the measuring complex in the harsh conditions of ice tests, it is based on the industrial measuring platform NI CompactRIO, which provides mechanical strength and operation at negative temperatures.The system provides for operation both under the guidance of an operator with displaying the voltages removed from the ship's hull in the form of graphs on a computer screen connected to the strain gauge station via an Ethernet line, and in stand-alone mode, when the recording of a given duration is initiated by the station on pre-configured events: amplitude exceeding by one of channels, an external discrete signal or periodically at specified intervals.
-
product
Strain Gauge Measuring Instruments
It is a Strain Gage Indicator and also function as a Strain Gage Transducer Indicator.As a Strain Gage Indicator, it can support 10 types of bridges and dummies. While if used as a Strain Gage Transducer Indicator, there are 24 bits A/D converts to make the measurement.
-
product
Custom Bolt-On Strain Sensors
Our custom bolt-on strain gauge sensors are designed and manufactured to your application, based on your drawings and specifications, including all types of output formats. Ideal for dynamic load monitoring, capable of measuring and monitoring axle stress and weight with high accuracy.Do you have an application for strain gauge measurement that requires a quick and simple installation, repeatedly, in multiple locations? Perhaps you need a sensor with high environmental protection, which removes the necessity for time-consuming cleaning, complicated soldering and messy strain gauge adhesives?
-
product
PCI Strain Gauge Simulator Card, 2-Channel, 3k
50-265-102
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
product
PXI Strain Gauge Simulator Module 6-Channel, 350
40-265-016
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 350Ω) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
product
PCI Strain Gauge Simulator Card, 6-Channel, 350 Ohm
50-265-016
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
product
Torque Sensor
Futek Advanced Sensor Technology, Inc.
Torque Sensors manufactured in US by FUTEK Advanced Sensor Technology (FUTEK), offering a huge selection of Torque Sensors, utilizing one of the most advanced technologies in the Sensor Industry: Metal foil strain gauge technology.A Torque Sensor, is a transducer that converts a torsional mechanical input into an electrical output signal. Torque Sensor, are also commonly known as a Torque Transducer.
-
product
2-Hole Bolt-On Strain Gauge Sensors
Series 460
Datum Electronics offer two types of multi-element bolt-on strain sensor that have been developed to provide a rugged and robust production sensor with the benefits associated with a complex strain gauge installation. They have been designed to measure tensile and compressive bending strains ranging from 50 to 1100 micro-strain. The gauges have been designed for use in applications including vehicles, civil engineering structures, silos, hoppers and specialist engineering projects.
-
product
Torque Instrument
DTR is a microprocessor based digital indicator, totally autonomousand with input for strain gauge based torque transducers.A ≤±0,02% accuracy makes it possible to be used use in qualitysystems as first or second line sample, periodically calibrated by aSIT center. Measuring system consists of a particularly long-termstable analogue section, of a carrier frequency amplifier whichminimises thermal drifts and of a 16 bits A/D converter whichensures 65.000 internal divisions.
-
product
4-channel Strain Gauge Amplifier Module
SCS-824
The SCS-824(5)(6)(7) provides 4 channels of strain gauge inputs for the SCS-800 signal conditioning system. It accommodates most strain-gauge types, from single-element quarter bridges to 4-element full bridges. Using included SystemView software, you can adjust excitation voltage, input gain, offset nulling, and all other key functions
-
product
Stress Analysis Strain Gauge
Structures can, and do, break, and this may be important and sometimes dramatic. It’s critical to determine whether a particular object made from a particular material can carry a particular load. If a true stress is ignored, the cost of not acting is usually far higher than the cost of dealing with the problem earlier. A well-done strain measurement will produce an accurate representation of the strain actually present under the sensor. Strain data, however, is seldom gathered as a means unto itself. It is usually little more than a convenient vehicle for indirectly obtaining information about some other engineering parameter.
-
product
PCI Strain Gauge Simulator Card, 4-Channel, 3k
50-265-104
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
product
Torsion And Shear Strain Gauges
Shear/Torque Strain Gages are for measuring shear strain and torque, typical applications are for measurements on torsion bars and determining shear stresses in shear beam load cells.
-
product
Strain Gauge and RTD via Ethernet
2612
Simultaneous measurement of four strain gauges or RTDs6 or 4-wire measurement with 200 nV resolution at a 6 Hz rateAuto-calibration cycle measures excitation at remote strain gaugeCompatible with Linux and WindowsUse our design assistant to configure a system and calculate pricing
-
product
PCI Strain Gauge Simulator Card, 6-Channel, 2k
50-265-306
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
product
Multiplexed- Low-Level Function Card
Low-level multiplexed systems have a single programmable gain, wide-band amplifier following the input multiplexer. To accommodate low-level signal signals such as those from strain gauges or thermocouples and at the same time high level signals from other sources, the throughput rate must be limited to enable the high bandwidth amplifier to settle to the correct value after switching to a new channel. This results in a relatively low aggregate throughput rate when compared to an amplifier-per-channel system. A major benefit of a well designed low-level multiplexed system is the extremely high performance/cost relationship.
-
product
Transducer Class® Strain Gages With Advanced Sensors Technology
Micro-Measurements Transducer Class® strain gages (gauges) and related products are a select group of gage patterns designed specifically for high volume transducer applications where a primary objective is optimal performance at a lower cost. Transducer Class strain gages are built with our Advanced Sensors technology, using state-of-the-art equipment and tooling for excellent performance and reduced lead times.
-
product
Strain Gauge for Measuring and Testing
Zhonghang Electronic Measuring Instruments Co. Ltd.
Zemic Strain Gauge for Measuring and Testing
-
product
4 2/3 Strain Gage Meter (1/32 DIN)
CS3-SG
CS3-SG Strain Gauge Indicator has been designed with high accuracy measurement, display and communication of DC signal 0~1.0/~4.0mV or 0~10.0/~40.0mV as like as Load Cell or Strain Gauge.The meter supports Field Calibration function. It can be calibrated with sensor(Load Cell/Strain Gauge) to meet machinery structure.They are also building in 2 Relay outputs, 1 External Control Input, 1 Analogue output or 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission or communication for a wide range of machinery and testing equipments applications.
-
product
FEA and Strain Gauge Testing
Circuit Check began Strain Gauge Testing in 1999 when BGA/SMT technology started replacing PTH components, reducing strain levels was a reactive post fixture fabrication process. We quickly recognized that the “reactionary” process was neither efficient nor were we capable on knowing the lowest achievable strain levels. Our engineering team came up with visual tools utilized during design to easily identify areas of excessive probe force, though still not enough data was generated to identify the lowest possible strain. Finite Element Analysis software models the PCBA and test fixture and applies the pressures from test probes and board supports and indicates the micro strain level applied to the PCBA. Using the FEA software during our design process allows our engineers to modify fixture designs to attain the lowest possible micro strain before fabrication begins.
-
product
Load Cell DIN Rail Signal Amplifier
LCD20
Our intelligent strain gauge bridge amplifier is a compact, stackable microprocessor based unit specifically designed to control and monitor process applications. Flexible connection to most load cells, pressure or strain gauges over a wide range of sensitivities. The unit provides isolated current 4-20mA and voltage 0-10V analogue outputs and two digital inputs. Two set point relays can be configured to set thresholds such as net, gross, peak and valley. Powered from a wide ranging DC supply, the DIN rail amplifier is supplied with 2 part screw connectors for ease of installation.
-
product
High Temperature, Low Strain, Extended Performance Capacitive Extensometers
Model 7650A
Jinan Testing Equipment IE Corporation
Model 7650A extensometers measure strains with extremely high precision due to their design features and low strain range. All models are capable of tension and compression strain measurement, and may be used for fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7650A models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to provide high accuracy, high resolution measurements and perform high temperature fatigue testing at the highest possible frequencies. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods for specimen contact when testing to 1200℃ (2200°F). Silicon carbide rods are used for the 1600℃ (2900°F) high temperature option.The Model 7650A is often customized for specific test needs. Contact Epsilon for a configuration that matches your requirement.
-
product
Bolt-On Strain Sensors
Datum Electronics bolt-on strain sensors are an ideal solution to many strain measurement requirements. They are robust, dust & water resistant, suitable for the harshest of environments, including high-stress level applications.Bolt on strain gauge sensors are compact in size, can provide temperature compensation (see out 3-hole bolt-on sensors) and have been designed to be easily installed without soldering or gauge adhesive.
-
product
Rugged, Long Gauge Length Extensometers
Model 3543
Jinan Testing Equipment IE Corporation
With over 15 years of proven reliability in the world’s most demanding testing environments, the Model 3543 extensometer is designed to survive in those applications where standard axial extensometers would not. Designed by Epsilon, the Model 3543 was created to survive specimen failure by separating into two halves, thus preventing permanent damage to the module body. During operation, the upper half of the extensometer pulls out of the main body. Tapered measuring beams activate strain gaged flexures within the unit. This unique design allows long measuring ranges, yet retains compatibility with electronics for strain gaged transducers. These models offer high accuracy and are light weight but rugged, with low operating force. They are tension only units.The units have hardened tool steel knife edges. Standard quick attach wires provided with the extensometer work on flat specimens up to 12 x 31 mm (0.5 x 1.25 inch) and on rounds up to 25 mm (1 inch) diameter. Optional quick attach kit wire forms are available for use on larger samples. See Model 3542L for long gauge lengths with smaller measuring ranges.The Model 3543 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
