Filter Results By:
Products
Applications
Manufacturers
Strain Gages
measure of displaced surface elements.
See Also: Strain Gauges, Strain Gage Amplifiers, Strain Gage Signal Conditioners, Strain
-
product
NI-9236, 10 kS/s/channel, 350 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module
779994-02
10 kS/s/channel, 350 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module - The NI‑9236 measures dynamic strain on all channels simultaneously, allowing for synchronized, high-speed measurements. This capability is important for applications, such as impact tests, that require comparison across many channels at a particular instant in time. The NI‑9236 includes built-in voltage excitation for quarter-bridge sensors. It also has 60 VDC isolation and 1,000 V rms transient isolation, providing high‑common‑mode noise rejection and increased safety.
-
product
Band-On Telemetry System
Advanced Telemetrics International
The ATi Band-On Telemetry System transmits real-time sensor data from a rotating shaft while the system is running. The system consists of one or more rotating signal conditioner/ transmitter modules with battery pack and a stationary receiver. Rotating transmitters are available to interface with most any type of sensor including strain gages, thermocouples, thermistors, RTDs and accelerometers.
-
product
SIRIUS Waterproof
SIRIUS Waterproof - Rugged and Modular Data Acquisition SystemExtremely rugged (IP67 degree of protection) and fully isolated rugged data acquisition system for the most demanding testing in harsh environments. High-precision, high-dynamic, and high-bandwidth for all types of analog signals from IEPE to strain gages.
-
product
Miniature S-Beam Load Cell
500 Series
The Miniature S-Beam Load Cell is a bi-directional Aluminium strain gage based transducer with high performance and builtin temperature compensation. This design provides better than ±0.1% (full scale) non-linearity and includes overload protection in both tension and compression directions. Options include IEEE1451.4 TEDS capability.
-
product
Digital FM Telemetry
90332
The 90332 digital FM telemetry systems is designed to be used with full-bridge, strain gage sensors. The system features a miniature transmitter powered by a simple 9V battery, and a remote receiver capability of receiving the digital transmission over long distances. The digital technique eliminates many of the problems associated with traditional analog frequency modulated telemetry systems. Improvements with a digital technique include elimination of ripple, temperature drift characteristics, and higher signal resolution.
-
product
Force Sensors
TE Connectivity (TE) designs and manufactures force sensors for applications that require high performance or unique packaging, including electro-mechanical flight control, test and measurement and ultra-low cost OEM load cells for medium to high volumes. Based on our proprietary piezoresistive silicon strain gage (Microfused) technology, our sensors combine durability and long-term stability in extremely low cost packages.
-
product
Low Profile Compression Only Load Button Load Cell with Mounting
LBM SERIES
The LBM Series (Load Button) load cells are offered for compression only applications where space is limited. This load button is a direct replacement for many of the same type and bolt patterns currently used in the industry. The matching surface must be flat and at least 2 inches in diameter. The loading diameter is slightly convex for accurate load distribution. Eight threaded mounting holes are provided on the bottom surface for fastening down from beneath. These sensors are manufactured from heat treated 17-4ph stainless steel, and the sensing element incorporates bonded foil strain gages of the highest quality. They are sealed for protection against most industrial environments.
-
product
Torque Transducers
The technology behind our torque sensors are strain gages. These gages are arranged into a Wheatstone Bridge circuit, which converts the physical, mechanical force into an electrical signal that can be filtered, displayed, and recorded for further processing. This very accurate radiometric electrical signal is proportional to the applied mechanical force.
-
product
Through Hole Load Washer Load Cell Compression Only
LWO SERIES
The LW0 Series are washer shaped, strain gage based load cells that have been most commonly used in fastener testing and thru hole load applications. Our stocked ranges from 2,400 through 300,000 lb compression are made from 17-4ph heat treated stainless steel and are matched to bolt diameters and their specific load characteristics. Modifications of diameters, thicknesses, or load range to a specific diameter for OEM applications are welcomed. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
product
Rosette Strain Gauges
Rosette Strain Gages have three measuring grids arranged at an angle of 0°/45°/90° or 0°/60°/120°
-
product
NI-9235, 10 kS/s/channel, 120 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module
785995-01
10 kS/s/channel, 120 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module - The NI‑9235 measures dynamic strain on all channels simultaneously, allowing for synchronized, high-speed measurements. This capability is important for applications, such as impact tests, that require comparison across many channels at a particular instant in time. The NI‑9235 includes built-in voltage excitation for quarter-bridge sensors. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety.
-
product
sbRIO-9219, Non-Enclosed, 100 S/s/channel, 4-Channel C Series Universal Analog Input Module
781027-01
Non-Enclosed, 100 S/s/channel, 4-Channel C Series Universal Analog Input Module - The sbRIO‑9219 is designed for multipurpose testing. With the sbRIO‑9219, you can measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors, as well as make quarter-bridge, half-bridge, and full-bridge current measurements, with built-in voltage and current excitation. Each channel is individually selectable, so you can perform a different measurement type on each channel. Non-enclosed modules are designed for OEM applications.
-
product
Through Hole/ Donut Load Cell Compression only (1.50 O.D.)
THB SERIES
Our THB Series through hole donut load cells offer anoutside diameter of 1.50 inches and up to four different thru-hole diameter options per capacity range. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
product
Precision Gram Load Cell Universal/ Tension or Compression
GSO SERIES
The GS0 Series Load Cells can be utilized in tension or compression or both with excellent compliance. The force sensing end of the anodized aluminum GS0 Series is tapped 6-32 thru for attachment possibilities for almost any application. Bonded foil strain gages at the sensing element provide for excellent stability over the suggested temperature range and ensure long term reliability. Call for application assistance.
-
product
16-Channel Bridge Signal Conditioning Unit
ProDAQ 5716
The ProDAQ 5716 is a 1U high rack-mountable signal conditioning box for standard 19 in. racks. It provides signal conditioning for up to 16 strain gage or ICP sensors. Either one ProDAQ 3416 16-Channel ADC Function Card or up to two ProDAQ 3424 8-Channel 24-bit Sigma-Delta ADC Function Cards can be connected to the unit.
-
product
DC Source/Calibrators
Our DC Source/Calibrators are designed for a typical applications such as the design, check and calibration of high speed, high resolution A/D converters; design and certification of high speed data logging and process control systems; calibration of digital voltmeters and multimeters; as an “IMBEDDED STANDARD” and/or simulator; design, testing, simulation and certification of thermocouples, strain gages and transducer instrumentation.
-
product
4-20mA Bridge AmplifierR
90416
This miniature, on-board, transducer amplifier is capable of supplying excitation voltage and amplifying millivolt signals from strain gage based transducers.
-
product
Load Cell Simulator
LCS-3
Load cell simulator particularly useful in a test environment for example to check a program sequence of a controller. The LCS-3 is a simulator used as a substitute for strain gage transducers to generate the precise mV/V signals required in the development , checkout and pre-calibration of signal conditioners, digital and analog readouts and data loggers.
-
product
Socket Wrench Torque Sensor Reaction Type
SWS SERIES
Our SWS Series reaction type socket wrench torque sensors are available in ranges from 10 ft-lbs. through 1000 ft-lbs. and provide accurate measurements of bolt or nut wrenching torques. These sensors are bi-directional so both tightening and break-away torques can be measured. These low cost sensors deliver high accuracy and outstanding frequency response. alibration of mechanical torque wrenches may be performed with this sensor. The sensing element incorporates bonded foil strain gages of the highest quality.
-
product
Fracture Mechanics Clip-On Gages
Model 3541
Jinan Testing Equipment IE Corporation
The Model 3541 is designed for determination of fracture mechanics parameters such as JIC, KIC, R-curve, fatigue crack growth rate (da/dN), and testing to standards such as E1820, E399, E647, etc. These COD gages conform to the requirements of E1820 (the replacement for E813 and E1737) for JIC and R-curve determination. Special configurations are available to meet the requirements of ASTM E399 for fracture toughness (please consult the factory for these configurations). In addition, the modified groove design complies with E1820 tests where greater stability and accuracy results from the sharper groove root. Clip-on gages are used for a variety of fracture mechanics tests, including compact tension, arc shaped, disk shaped, bend specimens or other specimen geometries in compliance with ASTM and other standards organization’s test methods. Clip-on gages can be used directly on test specimens where the knife edges are integral with the test specimen or, alternately, with optional bolt-on knife edges mounted on the test specimen.The Model 3541 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Strain Gage Testing - Stationary and Rotating
Verify analytical models Establish safe operating loads Applicable to high temperatures and aggressive environments
-
product
Strain Gage Testing
Response Dynamics Vibration Engineering, Inc.
Although strain measurement is often a key part of a root cause diagnosis, our analyses often also involve measurements of other parameters such as acceleration, relative displacement, pressure, temperature, flow, speed, load, dynamic stiffness, etc, to explore multiple parameters that may have a cause/effect relationship with the problem at hand. These measurements form part of a fact based hypothesis for the cause of the problem at hand. We use stain gauge testing and/or stain modeling and analysis, in conjunction with our structural dynamics expertise to characterize all the important pieces of the puzzle that come into play with dynamic strain issues (See Diagnostic Testing).
-
product
Stress Analysis Strain Gages
Bondable foil strain gages (strain gauges) available in thousands of possible pattern designs and combinations of grid alloys, backing materials, resistances, and options.
-
product
Junction Boxes
VPG Transducers created one of the largest load cell and transducer manufacturers in the world when we brought decades of weighing and force measurement experience under one roof. By harnessing the power of our collective expertise and experience in advanced strain gage technology, we are able to continuously challenge the status quo. As trusted partners, we are committed to providing world-class solutions that meet your needs.
-
product
T-Rosette Strain Gauges
Tee Rosette Strain Gages are for measuring orthogonal strains when the principle directions of stress are known. All patterns have two grids oriented at 0° and 90° angles.
-
product
Propeller and Rotor Blade Strain Measurement Systems
Advanced Telemetrics International
ATi Telemetry Systems are typically used to transmit data from rotating shafts or machinery to a stationary telemetry receiver. The 2040BC Miniature Strain Gage Transmitter can be connected to strain gauges adhered to propellers or rotors in order to transmit blade strain or shaft torque in flight.
-
product
Mini Load Column Load Cell Compression Only with Mounting
MLC SERIES
The MLC Series is our miniature high capacity compression only load cell/force sensor, featuring low profile compact size for a wide range of portable and dedicated applications up to 30,000 lb The load diameter is slightly convex for accurate load distribution. Low deflection through design results in ultra fast frequency response. The MLCs are designed to be mounted in a shallow machined flat pocket or smooth flat surface, either free or fastened via a bottom 6-32 tapped hole. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial Environments.
-
product
Rotating Dual Shaft Torque Sensors
RST SERIES
The RST- Series is our low range rotating torque sensors that are available in eleven full scale ranges of 10 through 30K inch pounds. The sensing element incorporates bonded foil strain gages of the highest quality along with coined silver slip ring and silver brushes for data transmission. The WR2, Flexural Natural Frequency, and Torsional Stiffness values as stated in the Dynamic Characteristics box below, are approximate and the tabulated data pertains to the torque pickup only, and does not include the effects of couplings or other rotating masses that would be part of a dynamic system.
-
product
Load Washer
5000 Series
The Load cell is a stainless steel sub-miniature strain gage based transducer with compensated temperature performance. This type provides measurements up to 20000 lbf with better than ±0.5% (full scale) non-linearity
-
product
Torque Verification
90229
SDI’s 90229 is designed for calibrating tools used to apply torque including electric and pneumatic power tools, torque sensors, hand and click wrenches. The strain gage based reaction torque sensors in the bench-mount housing remain stationary while torque is applied. The housing dis-assembles by removing two snap pins, allowing the user to easily change socket sizes and capacities.
