Filter Results By:
Products
Applications
Manufacturers
Solar Simulators
replicate the sun's light.
See Also: Solar Simulation, IEC 60904-9, I-V Tracers, Solar Reference Cells
-
product
Solar Reference Cell
The Solar Reference Cells consist of a 20 mm x 20 mm monocrystalline silicon Photovoltaic Cell encased in a 92 mm x 70 mm x 16 mm metal enclosure with a protective quartz window and a temperature sensor. Designed for calibrating the irradiance of solar simulators used for testing solar cells and modules.
-
product
Flash Solar Simulators
Sciencetech manufactures a range of flash solar simulatorsSee the Flash Solar Simulator Overview to compare products across different product lines.
-
product
Steady-state Solar Simulator For PV Modules
SORAS LS
In certification laboratories for photovoltaic modules, steady-state solar simulators are mostly used for stabilization / light soaking tests (MQT 19) and hot-spot endurance tests (MQT 09) according to IEC 61215 and IEC 61730. An initial stabilization is required for all PV modules that undergo a standard test procedure. For the hot-spot endurance test (MQT 09), it is important that the operator has easy access to the front and back site of the module. During the test, it is necessary to shade one cell after each other to take infrared pictures, which requires good visibility of the entire back side. Our swiveling module holding system enables easy access to the front and back side of the module.
-
product
Modular Power System 6kW Mainframe, 200/208 VAC
MP4301A
The MP4300 Series is a family of 1kW Solar Array Simulators (SAS) modular systems in a 2U footprint. The 6kW mainframes can accommodate up to 6 slots of SAS modules achieving excellent power and channel density. Additionally, the SAS series provides a way to simulate solar panels in a spacecraft while offering the highest density, efficient and reliable operation, minimizing rack space to provide the best total cost of ownership.
-
product
Fully Reflective Solar Simulators
Sciencetech manufactures four high power versions of class AAA fully reflective solar simulators. Sciencetech''s proprietary fully reflective design uses metal coated mirrors and passes the whole spectrum, no compromise. This is a distinct advantage over refractive based systems that are limited by the properties of the transparent material used.
-
product
Solar Simulation
Sciencetech solar simulators produce high intensity, uniform illumination on a target area. Typically, high power solar simulators use an ellipsoidal reflector to capture light from an arc lamp source inside the reflector, an arrangement that results in a light pattern with a bright outer region and a dark center. This non-uniformity is un- acceptable in many solar simulator applications and as a result, forces many of our solar simulator competitors to use designs involving diffusers to reduce the non-uniformity. This results in a reduction of intensity and a dis- tortion of the spectrum on the target area.
-
product
Large Area Pulsed Solar Simulators
Alpha-Omega Power Technologies, LLC.
AOPT introduces the large area pulsed solar simulator capable of generating a CLASS A output over a large area of 3.5 meters by 3.5 meters.
-
product
Electrical Ground Support Equipment:
EGSE
Keysight provides a variety of configurable test systems for satellites and satellite flight hardware; including Solar Array Simulators, Battery Simulation and Conditioning, RF signal simulation and analysis as well as fully custom solutions.
-
product
Portable Solar Simulator
XES-40S3
We have manufactured the highly accurate solar simulators, which is used for evaluations where sunlight needs to be recreated. By fully utilizing these technologies, we have developed this portable Solar Simulator, which can easily reproduces sunlight. Our device is optimum solution for initial evaluations and inspections for the research purpose.
-
product
Solar simulators
Solar simulators enable the measurement of (dark and) light IV characteristics and of power and efficiency of photovoltaic An artificial light source is used to create illumination conditions that are similar to those in natural sunlight. International standards hosted by ASTM, IEC and JIS allow to classify the properties of a solar simulator with respect to spatial light uniformity, spectral content of the light and time variation of intensity.
-
product
TriSOL Class AAA 0.25º Collimation Angle Solar Simulators
For high performance space applications, OAI offers a 0.25 Collimation Angle Solar Simulator. It is engineered with the technology built on OAI’s 47 years of experience working with light. Features include 100mmx100mm beam size, long lens housing, AM 1.5 G and AMO spectrum up to 1800 nm or any custom spectrum, and intensity controlled up to 1.25 SUNS. These solar simulators are built with OAI’s precision, quality and reliability.
-
product
Solar Simulator for Concentrator Cells
Optosolar offers solar simulators with continuous light for small area solar cells (ca. 10mm x 10mm). depending on the cell size, the concentration ratio can exceed 1000 suns. Special designs cover low concentration on large area wafers (156mm x 156mm), as well as line focus applications (e.g. 8mm x 156mm at 8 suns). Flashlight Solar Simulators have the advantage of negligible temperature change to the solar cell. For this reason, they are often used for very high concentration ratios or for multijunction cells in a solar simulator with adjustable spectrum.
-
product
Standard Class AAA Solar Simulator
TriSOL TSS
Essential for testing virtually any material or product that is exposed to sunlight for long or short periods of time, OAI’s low-cost, Standard Solar Simulators deliver highly collimated, uniform light. Depending on configuration, output on these Solar Simulators is rated at 350W -5,000W.These Class AAA Solar Simulators feature OAI’s Advanced Uniform Beam Optics and are available with a choice of air mass filters to reproduce a wide range of solar spectra. For added flexibility, OAI’s proven lens and collimating mirror technology allows for a variety of exposure area sizes. A Class AAA Solar Simulator is an essential tool for manufacturing as well as R&D; it is indispensable in test labs, industry, and in universities. OAI Standard Solar Simulators are used in photobiology, biomedical, solar cell testing, cosmetic testing, and paints & coatings analysis. Based on 35+ years of proven UV light technology, OAI Solar Simulator Systems deliver repeatable, reliable, constant output, and measurement uniformity.
-
product
TriSOL Large Area Solar Simulators
OAI has designed and engineered for large area markets Class AAA, ABA, or ACA Solar simulators with the same performance , quality, and reliability as our other solar simulator models. These large area solar simulators are available in several models.
-
product
Solar Simulator
Sirius 150A
Solar Simulators are used to simulate “real” solar radiation conditions and are widely used for the photovoltaic device research and QA etc.Beam collimation and spot uniformity are important properties along with spectral matching are key operational requirements. The SS150 and SS1000 are suitable for all types of solar cells and well match their optical requirements.
-
product
Flash Solar Power Meter
OAI’s Flash Solar Power Meter is a versatile measurement tool used for measuring the irradiance (in Suns) from Flash Solar Simulators. Flash Solar Simulators are commonly used in the production of solar panels. Integrated into the solar cell production line, this meter calibrates the flash solar simulator allowing for constant and repeatable irradiance output. By sampling at speeds up to 4000 Hz, the flash pulse temporal profile can be recorded in the meter’s memory and downloaded to a USB 2.0 port on a PC for further analysis.
-
product
Highly Collimated Solar Simulators
This solar simulator is based on a Fresnel lens to collimate the light beam from the arc lamp source to infinity, which results in highly collimated illumination of the target spot. A 2.5kW xenon ozone free lamp is used as the light source. The spectral distribution of the xenon light source, along with the use of specially calibrated AirMass filters, closely simulates the sun’s true spectral distribution in various conditions on Earth.
-
product
Reference Cells
Reference cell is used for measuring and setting the intensity of solar simulators for one sun (or other user desired) intensity condition. They are also used to calibrate the IV Measurement system photo-detector intensity to match the measured ISC to calibrated ISC.
-
product
Full 4-Quadrant Grid Simulator
TC.ACS
The increasing number of alternative power sources like solar, wind driven or biological energy systems call for consistent and well demanding regulations for energy feed into the utility grid. Manufacturers of such systems have to test and to prove the compliance of their equipment. Grid simulators form an electronic equivalent circuit for the grid, but allow to vary all relevant parameters in order to test the behaviour and response of the equipment under test.
-
product
Testing Consumables
Solar Light offers a plethora of consumables for SPF and other testing requirements, including high quality Molded and Sandblasted PMMA Plates, Pre-Analyzed and Certified SPF and UVA Sunscreen Standards, Disposable Medical-Grade Pads, and long-life spare Xe Lamps for use with our state of the art Solar Simulators.
-
product
LED solar simulators
We offer innovative A + A + A + LED solar simulators for the integration of the production process and for the stand-alone operation in the laboratory or goods receipt. Our LED solar simulators are characterized by maximum repeatability, a long pulse duration and very low maintenance.
-
product
Solar Simulators
Abet Technologies offer a wide range of ASTM, IEC, and JIS standards compliant solar simulators ranging from 150W to 3kW with one sun or greater illuminated field sizes from 50 x 50 mm to 35 x 35 cm. The direction of illumination, traditional down pointing, horizontal, or vertical up pointing can be specified at the time of ordering.
-
product
Aerospace and Aviation Solutions
SCOEs and EGSEs by LXinstruments are used during test and validation of satellite assemblies and modules in aerospace applications. As an example, we implemented solar array simulators, battery simulators and high-power load racks for a German satellite manufacturer for testing satellite power supply systems. Due to the high power ratings, the systems are partially equipped with water cooling. Specialized switching modules were developed for switching DC currents at high voltage levels; these can be programmed with SCPI commands via Ethernet.Our modular OTP² functional test platform is ideally suited for implementing durable, reliable test systems, e. g. for in-flight entertainment applications. Since the OTP2 platform is based on open interfaces, it can be quickly and easily adapted to any required communication busses and ARINC interfaces.
-
product
Continuous Wave Solar Power Meter
The OAI Continuous Wave Solar Power Meter is an essential analytical tool for measuring the irradiance (in Suns) of Continuous Wave Solar Simulators. OAI’s Solar Power Meters feature unique features not found in other Solar Meters. This versatile meter can display a wide variety of cell characteristics that include: cell type, window type, cell size, and temperature measurement device type. The OAI Continuous Wave Solar Power Meter can sample and display a continuous reading or peak reading. The Power Meter connects via USB port for data collection, and includes desktop software. With this small, portable, battery-powered meter, numerous production solar simulators can be tested and compared in a short amount of time, leading to greater production line consistency and throughput.
-
product
Solar Simulator
Unisim
TS-Space Systems is the first company to pioneer the use of metal halide sources in solar simulators for photovoltaic testing. The high temporal stability and close spectral match combined with the ability to control the output spectrum via multiple separate wavebands means the Unisim solar simulator is the only solar research tool designed for the accurate measurement of multiple junction devices, including the new generation of four junction devices. As with all our Unisim solar simulators, they exceed the ASTM, IEC and JIS international standards for spectral match and temporal instability. Using the latest HMI and halogen luminaire technology, the Unisim solar simulator provides a highly stable area of illumination. The simulators also use cutting edge filter technology in order to provide the best spectral match available for AM0 and AM1.5. Further to this, the spectrum can be achieved via two, three or four separate spectral wavebands which allows a high degree of spectral control for research and development. Product support is very important to us. Training is provided at our premises where customers can take advantage of one-on-one tuition with the instrument designers and learn how to operate and maintain their tools. Extensive support via phone and email for the full lifetime of the instrument is included with every TS-Space Systems product.
-
product
Standalone Terrestrial Solar Array Photovoltaic Simulator
TerraSAS (ETS Series)
AMETEK Programmable Power, Inc.
For microgrids, energy storage, and inverter test applications, the TerraSAS™ series photovoltaic (PV) simulators are specifically designed to emulate the dynamic electrical behavior of a terrestrial PV solar array. They offer low output capacitance and high closed loop bandwidth to keep up with the advanced Maximum Power Point Tracking (MPPT) algorithms used in today’s grid-tied inverters. The Embedded TerraSAS (ETS) is a high performance solution in a small form factor that combines an agile power supply with an innovative I-V curve generator in a single standalone unit.
-
product
Sunlite Solar Simulators
- Gen III Optics for High Efficiency Illuminati- Infinitely Adjustable Irradiance, Reproducibly Settable- Class A AM1.5G Spectral Match- ASTM Class A stability- 50×50 mm Class B uniformity- Manual Shutter Included, Electronic - Shutter Optional- Uninterrupted testing with the prealigned lamps- HEPA filtered air cooling
-
product
Large Area Solar Simulators
The LASI Beam Turner assembly allows the output of the LASI to be projected horizontally. It attaches to to the standard LASI downward facing stand that is included in the base LASI system.
-
product
Light Simulator
From the review of the scientific development history, reliable and stable artificial light sources have played a very important role in the past century. For example, the artificial solar simulator is an important part of simulating sunlight to ensure accurate performance of PV characterization. With the growth of light sensor applications, more and more requirement of light simulators (or artificial light sources) explored. One of the core technologies of Enlitech is the artificial light sources. We can manipulate different lamp types (short arc lamps, LEDs, filament lamps et. al.) to generate different spectrum-form in different light intensity levels, beam sizes, and wavelength ranges. We have launched different artificial light source products for different applications fields. For instance, SS-X series solar simulators and ILS-30 ambient light simulator are for the PV field, HAAS is highly accurate star light simulator for the space field, and ALS-300 is a general-purpose light source in science research field. These products can not only meet the needs of your application, but also speed up the process of your research or mass-production.
-
product
UV Solar Simulators
UV Solar Simulators - please contact the company directly for more information.
