Filter Results By:
Products
Applications
Manufacturers
Signal Conditioning Systems
-
product
Thermocouple Interface Amplifiers
Analog Devices offers specialized precision thermocouple interface amplifiers that provide a simple and effective solution for measuring thermocouple temperatures. With features such as integrated cold junction compensation and a high gain precision instrumentation amplifier, these thermocouple amplifiers provide a complete signal conditioning system in one IC package. ADI’s thermocouple amplifiers are suitable for use in diverse environments to measure a wide range of temperatures. These products will save you in cost, space, and unnecessary circuit design across a broad range of applications and industries.
-
product
Sensor Signal Conditioning System
SCS
SCS Sensor Signal-Conditioning System complements the iDSC 1816 anti-aliasing board to provide a continuous path in a single package: starting with raw measurements at the sensor and ending with conditioned anti-aliased data logged to disk on a PC.
-
product
4 Channels of Strain Gauge Inputs for the SCS-800 Signal Conditioning System
SCS-817
The SCS-816 and SCS-817 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-816) and 0.5Hz to 60kHz(SCS-817). Each of the SCS-816/SCS-817's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
product
Signal Conditioning System
SCS-801
The SCS-800 is a high-performance signal conditioning system for PC-based data acquisition. An SCS-800 system consists of an AC operable chassis and up to 8 multi-channel modules.The SCS-800 takes advantage of the increasing capabilities of notebook and desktop PCs by leveraging off the PC's strengths. It provides a high-performance, flexible solution whether used as a conditioning front-end for desktop systems in the factory or as a mobile solution for portable systems in the field.
-
product
4-channel Strain Gauge Amplifier Module
SCS-824
The SCS-824(5)(6)(7) provides 4 channels of strain gauge inputs for the SCS-800 signal conditioning system. It accommodates most strain-gauge types, from single-element quarter bridges to 4-element full bridges. Using included SystemView software, you can adjust excitation voltage, input gain, offset nulling, and all other key functions
-
product
6 Channel Signal Conditioner & Data Acquisition Module
DP-cPCI-1197
DP-cPCI-1197 is a high-resolution signal-conditioning module that amplifies the signals from full-bridge based transducers. This signal-conditioning module is available on a cPCI module form factor. This module has four gain settings to accommodate a wide variety of sensor output voltages. In addition, this module has an adjustable excitation voltage to accommodate transducer excitation requirements.A high resolution sigma-delta ADC and variable gain amplifier forms the core of the signal conditioning system. Direct digital conversion and digital isolation ensures a better signal integrity in comparison with the conventional analog system.
-
product
Large Electrical Machines Bench Testing
The automated system for recording parameters during testing of gas turbine generators consists of several independent but interacting measuring subsystems and a signal conditioning system. The subsystems for recording "fast" signals are implemented on the PXI platform, "slow" signals are registered by a subsystem built on the basis of the Compact FieldPoint platform.
-
product
Signal Conditioning System
28000
The Precision 28000 Signal Conditioning System makes it easy to manage a test with up to 256 channels of fully programmable transducer conditioning. Choose a mix of bridge, charge, IEPE w/TEDS, voltage (filter amplifier), strain, thermocouple, RTD/potentiometer, frequency, or other transducers. Self-tests traceable to NIST. 4, 8 and 16-slot rugged and transportable mainframes feature integrated cooling. Customize the 28000 for high-speed transient applications, static applications, or a combination of both.
-
product
LabVIEW Full Development System
LabVIEW is engineering software designed specifically for test, measurement, and control applications that require rapid access to hardware and data insights. The LabVIEW Full Development System is recommended to customize your engineering application with advanced inline analysis and control algorithms. For applications that require software engineering tools to develop, debug, and deploy professional applications, consider LabVIEW Professional Development System.
-
product
Cobra Temperature Forcing System for ATE/SLT Test Applications
31000R
Cobra is the most advanced, compact,powerful temperature-forcing system on the market. Cobra is an adaptable solution to the ever-increasing thermal demands of post silicon validation and device characterization.
-
product
Battery Cell Formation System
17000 series
Chroma 17000 series is specifically designed for the formation of Lithium Ion and Lithium Polymer secondary batteries. The 17000 series is a complete turn-key system, including carrier trays, robust battery probe contacts, high quality charge/discharge modules and intuitive software all under computer control. Patented Battery Voltage Tracking (BVT) DC-DC conversion power modules minimize power consumption in battery charging, and Energy Recycle Modules (ERM) recycle the discharged energy directly back to the DC power system for increased power efficiency. These power saving designs provide a planet friendly solution along with cost savings by reducing energy consumption. The intuitive software provides a flexible selection in the charge/ discharge channel, current rating, and modules under test. These features allow the Series 17000 to be used for final cell development, pilot line production, high volume production and ongoing reliability monitoring/quality control.
-
product
COTS Systems
Pre-integrated to save you time and money, pre-validated systems proved an optimum computing platform for mission applications.
-
product
Mezzanine System
5181 MMS ECM
ECM P/N 5181 uses TI TLV320AIC23 high resolution audio codecs to provide two channels of Audio input and two channels of Audio output. Each input channel consists of two inputs a left and a right, and each output channel consists of two outputs left and right. The outputs are muteable.
-
product
Mezzanine System
5033
ECM P/N 5033 provides eight channels of RS485 / RS422 I/O. The 110 ohm termination for each channel is enabled or disabled in software. Disabling termination saves power by eliminating unneeded or redundant termination. Speeds of up to 20 Mega bits per second are possible, but this design also features a 250K bits per second slower edge rate mode. The 250K bit mode is valuable when EMI is more of a concern and throughput is not important. All channels power up as inputs with the outputs disabled.
-
product
IFEC Embedded System Hardware
State-of-the-art system components serve as building blocks for you to create the ideal IFEC system.
-
product
Mezzanine System
5676
The Abaco SystemsP/N 5676 ECM module provides eight channels of 16 bit voltage measurement in the 0 to 2.5V volt range. For each channel the common mode voltage range is -100 volts to +100 volts.
-
product
Development System
PCIe490
The PCIe490 Expansion Chassis enables users to scale application workstations with up to eight additional PCIe boards per chassis and up to 63 total slots with chassis daisy chaining. It was designed to accommodate the Abaco Systems PC820 and PC821 with Xilinx Ultrascale technology and multiple FMC+ interfaces.
-
product
Mezzanine System
5093
ECM P/N 5093 provides 2 independent full bridge circuits. The two full bridge circuits can be used together to drive one small two phase stepper motor. Each full bridge circuit can drive one small dc motor or other bipolar load. Note all inductive loads should employ transient protection.
-
product
VME Data Acquistion System
ADM-31
The VME-based ADM31 data acquistion system supports up to 48 differential or up to 96 single-ended analog inputs. The ADM31 control card is an intelligent A/D subsystem master or slave device that controls the analog A/D cards. Up to two A/D cards can be configured with the control card to complete the A/D system.
-
product
Validation System
FLEX BMS
The FLEX BMS™ Validation System is a quick-connecting, highly flexible test system for rapid evaluation of centralized, single-board and distributed battery management systems. Utilizing Bloomy’s industry-leading battery cell simulators, COTS instrumentation, industry-standard connectors, and models that run in real-time, the FLEX BMS™ Validation System can easily be reconfigured to test a wide variety of BMSs. The FLEX BMS™ Validation System is used by national and regional safety and standards labs for certifying the BMS for a wide array of e-mobility products and applications.
-
product
Systems Certification
Project integration offering a complete turnkey solution including design, engineering, FAA and international regulatory certification services and testing, and installation kit manufacturing.
-
product
Mezzanine System
5081
The 5081 provides four channels of 12 bit digital to analog voltage output, with multiple single ended output ranges. Each channel is software selectable for 0 to +5V, 0 to +10V, +/-2.5V, +/-5V, +/-10V or -2.5 to 7.5V ranges. The outputs reset to 0.0 volts on power up.
-
product
LabVIEW Development Systems
Base--The instant productivity of graphical development for DAQ and instrument controlFull--A rich set of routines for mathematics, signal processing, and signal generationProfessional--The solution for professional developers who need code deployment or validationLabVIEW suites--LabVIEW Professional plus industry-specific add-on software
-
product
VPX Processing System
CRS-D4I-3VB1
4-slot, SWaP-reduced, rugged VPX Intel base plate cooled data processing system that can be applied across various applications including civilian and military unmanned vehicles, manned commercial and military aircraft, helicopters, over- and underwater research vessels, ground vehicles, and locomotives.
-
product
Test Requirements Document (TRD) System
TRD Software
The Test Requirements Document (TRD) System helps users develop and document the strategy and structure of test programs.
-
product
ESD Test System
58154 Series
ESD (Electrostatic Discharge) Test Systems are PXI/PCI controlled module to simulate electrostatic discharge pulse during electronic device testing. The 58154 series offer both ESD STM5.1-2001-Human Body Model and ESD STM5.2-1999-Machine Model. The user friendly software offers programmable and flexible features, such as sampling test on a wafer, ESD model, ESD pulse polarity, ESD pulse interval in a sequence, and automatic testing function.
-
product
Communication Test System
CTS-2700
The CTS-2700 is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The field-upgradeable, software-defined architecture features easy-to-use graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets can be created easily using the included TestEZ® software suite.
-
product
FMV Compression System
daq8580
The Daq8580 is designed to address the challenges of processing, transporting and storing full motion video through video encoding, and can interface with a wide variety of analog and digital I/O and process standard video formats up to 1080p30 as well as computer resolutions up to 1600x1200.
-
product
VIP Inflight Entertainment Systems
Astronics can outfit your entire cabin with the perfect A/V system to match your needs. From a custom monitor to a robust speaker system, Astronics' integrations will improve your inflight entertainment experience.
-
product
Iridium Physical Layer Test Systems
PLTS
Averna has worked with Iridium to ensure you have the right equipment to support their test coverage. The Iridium PLTS verifies product performance to Iridium’s standards. Find out more!
