Filter Results By:
Products
Applications
Manufacturers
-
product
TestCentre
ARC has experience with complex, commercially available test executives that are available for high volume production needs. Often times, when you don’t need the horsepower of a full featured executive, you are left with creating a specifically defined test program or crafting your own test sequencer. Rather than go down this path and spending your time on architecture, TestCentre brings a simple, yet elegant solution to this all-common problem. Used in many of ARC’s standard test stations, the robust, sequence based architecture of TestCentre, allows you to focus on the testing task at hand. While having some of the more advanced features found in high-end test executives, TestCentre, when mixed with RF analyzers and PXI based test solutions are a great, low cost solution to help solve your everyday testing requirements. Along with TestCentre and an ARC supplied rack-based test platform, your test challenges can be solved in doing circuit card testing, assembly/module level testing, or depot repair troubleshooting tasks.
-
product
USB Type-C Interconnects Compliance Test Software
S94USBCB
Use the S94USBCB software to test, debug and characterize your USB Type-C cable and connector designs. The PathWave TAP based test sequencer automates the network analyzer (VNA) for each test and generates a comprehensive HTML report. When run with L8990M switch matrix, it enables 20-ports fully automated test without port re-connection.
-
-
product
Digital I/O PXI Card
GX5150
The GX5150 Series are high speed, 6U PXI, sequenced digital I/O instruments. The GX5150 master controller has 32 bits of I/O channels that supports test rates of up to 50 MHz and a vector depth of up to 128 Mb per pin. The GX5151 slave offers the same timing characteristics and multiple I/O level configurations when used in conjunction with the GX5150. The GX5150 can control up to 15 GX5151 boards using the same timing and sequencer.
-
product
PXI Semiconductor/IC Test System
A high-density 100MHz PXIe digital IO card designed for characterizing, validating, and testing a variety of digital and mixed-signal ICs. Each IO card consists of a Sequencer Pattern Generator (SQPG) and 32 channels of full ATE-like features. The 33010 IO card is expandable up to 256 channels. Some unique features of the 33010 include an on-board SQPG, per pin timing/levels/ PMU/TFMU, multiple time domains, and multithreaded testing for complex IC testing. Each channel is also equipped with 64M vector memory, 16 timing sets with on-the-fly timing change, and per pin timing and frequency measurements up to 400 MHz.
-
product
Point on Wave Synchronous Test Sequencer
The Portable Point on Wave Synchronous Test Sequencer is India’s only system that helps in time synchronizing the control signals during short circuit tests performed on medium and high voltage switchgear and control gear.
-
product
Pneumatic and electro-pneumatic controllers
Pneumatic-mechanical sequencer and command module. Stepper. Control block for two-hand start. Local controllers
-
product
Aircraft Escape Spares/Repairs
As the OEM of all of our products, both end items and support equipment, Teledyne can support all repair needs for end users. Turn-around times are typically less than 90 days with units being returned fully tested to their specific program requirements. All repairs are performed using new materials and components. Once the repair has been received, and purchase order issued, a Test and Evaluation report is sent to the end user fully describing our findings and the proposed repair.Following live ejections, Teledyne will download and prepare a post ejection report for any of our ejection seat sequencers AT NO COST to the end user. This report will document the data stored in the flash memory of the unit. The data will be a representation of what the sequencer recorded. However, Teledyne is unable to give any opinions or technical advice on the operation of the seat system.
-
product
1Gsps, 9 Channel, Logic Analyzer with Protocol Analyzer plugins and Hardware Compression
DigiView™ DV509
- Physical Channels: 9- Sample rate: 4ch@1 Gsps or 9ch@500Msps (4 ch. are sampled every 1ns or 9 ch. are sampled every 2ns)- Typical capture: 100M transitions (> 1B samples)- Hardware based triggers with 8 universal match circuits, and partitionable 16 stage sequencer- Adjustable Threshold (± 4V)- Real-time, Hardware-based, Adaptive Compression- Channels protected to ± 20V- Ground leads protected to ± 12V- High-quality test leads: 66 strand soft copper wires, flexible insulation, and gold plated connectors. Fit .025 square posts as well as the included clips.- Extra ESD protection- Streaming storage with auto fall-back to Store & Forward mode ensures large storage and reliability.- USB 3.0 (SS) or USB 2.0 (High Speed)- USB powered- Each DigiVIew includes all avialable Protocol Analyzer plugins (including: I2C, SPI, CAN, Async, Sync, 1-wire, I2S, TDM)- Free Plugin Developers' Kit- Requires Windows 7 or greater OS (32bit or 64bit)- Free Lifetime sofware updates.- 1 year warranty
-
product
PXI Device Power Supply - 4 Isolated Channels, 20-bit Measurement Resolution
52310e series
Chroma 52310e Series i s a programmabl e PXI-Express DPS (Device Power Supply) Card designed for high-accuracy and reliable output power for device test applications. Its compact size, easy level of integration, and high flexibility make the 52310e Series ideal for multi-channel power supplies. Chroma 52310e Series features 8 selectable control bandwidths to ensure high speed output and stable operation; multiple current measurement ranges with a 20-bit DAC/ADC provide the highest resolution and accuracy with a sampling rate up to 600K S/sec; programmable internal series resistance for battery simulation. Chroma 52310e DPS series has a patented hardware sequence engine that has deterministic t iming to cont rol each DPS channel. The sequencer's on-board memory can store up to 1024 sequencer commands and 32k measurement samples per channel.
-
product
TMS Test Management Software
LX TMS
To diagnose and analyze electronic components and devices, various tests are required in development, production and service. Equipped with all the necessary standard functions, the test sequencer developed by LXinstuments meets all criteria for a successful and smooth test process. The test item ( DUT ) is examined under various operating conditions for its properties, function and usability. Typical areas of application can be found where the usual complexity of test sequences has to be processed. The test sequencer is therefore suitable for small and medium-sized systems where special functions of other sequencers are not required. The free, cross-platform, open source developer platform .NET serves as a starting point. The integrated WPF (Windows Presentation Foundation) framework ensures a user-friendly program interface.
-
product
Aircraft Escape Systems
The Emergency Interseat Sequencing System (EISS) was designed an qualified for the F-15K Fighter and has since been installed in the F-15SG and F-15SA configurations of the F-15. The system consists of Thermal Batteries with Initiators, a Digital Interseat Sequencer, Mode Selector, and customer provided cabling Electro-Explosive Devices (EEDs). The system is operated from either thermal battery and aircraft 28Vdc for redundancy. A separate field Test Set (EESSTS) performs both complete system continuity tests and an operational test of the total system installed in the aircraft. The sequencer is programmable and could be used in any escape system.Based on the initiation point, Forward or Aft Seat Handle, Internal or External Canopy Jettison Handles, and the Mode Selector setting, the Sequencer provides firing pulses to the EEDs to support canopy removal, ejection seat inertial reel activation(s) and ejection seat catapult firing(s). Sensing capabilities are provided to determine system state, canopy gone, seat gone, so as to provide the optimum escape timing.
-
product
Series 5800 Conditioning & Transient Recording System I/O Modules
Data acquired by the 5800 is digitized and recorded in non-volatile, solid-state memory. It records calibration, pre-trigger and post-trigger data. In a typical test scenario recording of pre-trigger data is initiated by a TTL input, program instruction, or automatic sequencer. A TTL input or on-board discriminator triggers post trigger data recording.
-
product
Power Sequencing
Renesas' power sequencing controllers are integrated 4-channel controlled-on/controlled-off power supply sequencers with supply monitoring, fault protection and a “sequence completed” signal.
-
product
Rad Hard Power Sequencing
Renesas' radiation hardened quad power supply sequencers are designed to drive point-of load (POL) regulators that power high performance FPGAs and complex, multi-rail power systems.
-
product
VME Sequencer
SIS3100
The SIS3100 was developed as the VME side of our PCI to VME interface. The module is however perfectly suited for other custom applications like a histogramming multiscaler for LIDAR or a generic DSP controlled VME histogrammer .
-
product
Dynamic Digital I/O With Per Channel Timing, Programmable Logic Levels And PMU PXI Card
GX5296
The GX5296 offers advanced dynamic digital I/O performance and capabilities in a single slot, 3U PXI format. The 32-channel, GX5296 features timing per pin, multiple time sets, data formatting, and an advanced sequencer – providing users with the capability to emulate and test complex digital busses for system, board or device test applications. Offering sub-nanosecond edge placement resolution per pin and a PMU per pin, the GX5296 has the ability to perform both DC and AC parametric testing. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level). In addition, each channel offers a parametric measurement unit (PMU) providing users with the capability to perform parallel DC measurements on the DUT (device under test).
-
product
Power Monitors
Analog Devices’ power monitoring amplifiers provide an integrated solution for digital current and voltage measurement via an on-chip, 12-bit analog-to-digital converter (ADC), communicated through an I2C interface. Leveraging ADI’s precision analog design techniques, ADI’s products are twice as precise as competing devices, offering best-in-class accuracy (<±0.8%). The power monitors complete the industry’s only monitor and sequencer family to deliver <±1% accuracy for 2 to 12 supplies.
-
product
Automation Tool for the CMW Platform
CMWrun
The R&S®CMW is the leading multistandard UE testing platform used by network operators, test houses, handset vendors and chipset manufacturers worldwide. R&S®CMWrun automation software meets all requirements for executing remote control test sequences on the R&S®CMW for wireless equipment in R&D, quality assurance, production and service. The intuitive graphical user interface of the R&S®CMWrun sequencer software allows easy and straightforward test sequence configuration. No programming and code compilation are needed. At the end of the test, an easy-to-read test report of the limits, test results and verdict is generated.
-
product
Arbitrary Function Generator PXI Card
GX1200 Series
The GX1200 and GX1201 are high performance, single-channel PXI arbitrary waveform generators that combine a function generator, arbitrary waveform synthesizer, programmable sequencer, pulse generator, and modulation generator in one instrument. The GX1200 Series delivers all this at a lower cost than comparable benchtop or VXI-based instruments.
-
product
Digital I/O with Per Channel Timing, Programmable Logic Levels and PMU PXI Card
GX5296
The GX5296 offers the most performance and features of any 3U PXI dynamic digital I/O board on the market today. The 32-channel, GX5296 offers timing per pin, multiple time sets, data formatting, and an advanced sequencer – providing users with the capability emulate and test complex digital busses for system, board or device test applications. Offering 1 ns edge placement resolution per pin and a PMU per pin, the GX5296 has the ability to perform both DC and AC parametric testing. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level).
-
product
68-Channel Portable Logic Analyzer
16862A
68 channels, 350 MHz state, 12.5 GHz timing zoom, 2.5 GHz timing, 2 Mb depth standard15-inch (38.1 cm) color, touch-screen display for viewing and quickly navigating large numbers of signals and buses Built-in removable SSD drive, USB 3.0 ports and LAN for fast data transfer and storage of large amounts of data1.4 GHz trigger sequencer to ensure high-speed events are captured
-
product
PCB Test System
Circuit Wizard - CW409
Qmax Test Technologies Pvt. Ltd.
CW 409 –Circuit Wizard PCB Test System has all the features of QT9627 such as Desktop PCB Test System. It can be configured to maximum 64 Channels of In-circuit Functional Test Channels and 64 Channels of QSM V-I Signature Test.Maximum Digital Test Speed 10MHz in the QT9627 .It can be connected to any PC/AT or Laptop with Windows 10 operating system through USB Plug and play interface. It operates on user friendly Qmax Test Director software platform with different modes like Test Station for operator level use Test Sequencer mode for Programmer level use and Interactive Workstation mode for quick working.
-
product
CAMAC-to-FERA Bridge
CFB
The WIENER CFB is an intelligent, programmable, re-configurable CAMAC-to-FERA bridge with sequencer that allows one to interface both, common and custom-made CAMAC modules to FERA-readout-based data acquisition systems.
-
product
Dynamically Controlled High Speed Digital I/O PXI Card
GX5150 Series
The GX5150 Series are high speed, 6U PXI, sequenced digital I/O instruments. The GX5150 master controller has 32 bits of I/O channels that supports test rates of up to 50 MHz and a vector depth of up to 128 Mb per pin. The GX5151 slave offers the same timing characteristics and multiple I/O level configurations when used in conjunction with the GX5150. The GX5150 can control up to 15 GX5151 boards using the same timing and sequencer.
-
product
102-Channel Portable Logic Analyzer
16863A
102 channels, 350 MHz state, 12.5 GHz timing zoom, 2.5 GHz timing, 2 Mb depth standard15-inch (38.1 cm) color, touch-screen display for viewing and quickly navigating large numbers of signals and buses Built-in removable SSD drive, USB 3.0 ports and LAN for fast data transfer and storage of large amounts of data1.4 GHz trigger sequencer to ensure high-speed events are captured
-
product
Radar Simulation Software
Pulse Sequencer
R&S®Pulse Sequencer software together with a vector signal generator from Rohde & Schwarz or just as software provides a compelling radar signal generation solution to engineers and technicians responsible for testing radar receivers. The solution is in line with the trend of testing more in the lab rather than expensive field testing. Co-engineered with the industry, the solution supports all relevant modern radar scenario test cases and can account for real-world environments. It uses commercially available R&S®Pulse Sequencer PC software and off-the-shelf Rohde & Schwarz vector signal generators.
-
product
Insulation/Withstand Testers/Hipot Testers
Supports remote control For automatic multipoint testing of insulation / withstand voltage Use with the 3153''''s program or with general-purpose logic sequencers
-
product
Digital Sequencers
The Analog Devices Super Sequencer ® portfolio offers a total power management platform for monitoring, measuring, sequencing, and margining a large number of voltages. Our comparators provide ±1% accurate monitoring of rails, while 12-bit ADCs offer voltage readback via a serial interface. Applications utilizing these devices benefit from sequencing that has been custom tailored to their needs by powerful state machine cores, as well as DAC banks to trim or margin regulators. Our digital sequencers include on-board EEPROM for storing devices parameters and for latching information for later analysis.
-
product
Serial AC Power Sequencer
90-200-001
Each power outlet can be programmed to switched on in sequence with a specific timing delay. The delay can be staggered to ensure that order dependent systems - like PXI - can be switched on and off in an orderly way with just one operation. A staggered start up also limits the inrush current associated with the powering up of equipment, including earth current inrush, placing less stress on cabling and leakage breakers. Power on or off instructions can be initiated from either the front panel switch or via the serial interface.
