Filter Results By:
Products
Applications
Manufacturers
Sampling Oscilloscopes
Sample signals prior to any amplification or attenuation.
-
product
HandyScope HS5: 200 MS/s 250MHz BW, 2 Channel, USB Digital Storage Oscilloscope, 20MHz AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
HS5-220XM-W5
The Handyscope HS5 is the first USB oscilloscope (USB powered) sampling at 200 MHz, with a 14 bits resolution and a 250 MHz bandwidth. This makes it possible to analyze very fast signals with very small amplitudes. The smallest distortions can be revealed due to the high resolution and bandwidth. Because of the deep memory (up to 64 MSamples on one channel), long record measurements are available for intermittent phenomena and Fast Fourier Transform calculations with over 32 million spectral lines can be performed. Using very fast FFT algorithms, an FFT with 1 million spectral lines can be performed within a second.
-
product
DCA-M 10 GHz/14 GHz Optical & Electrical Sampling Oscilloscope
UC9110/UC9115
The UC INSTRUEMNTS UC9110/UC9115 DCA-M 10 GHz/14 GHz Optical & Electrical Sampling Oscilloscope is a high speed, performance, flexible one channel optical/electrical that can operate from 1.0 to 14.0 Gb/s (consult factory for higher or lower operation speeds). It is also a stand alone Eye-diagram analyzer test.
-
product
Logic Analyzer
GoLogicXL-36
Logic analyzers and oscilloscopes offering fast sample rates and large memory depths are required to debug and test modern electronics. The GoLogicXL captures a very large window of bus activity using sample depths up to 1 billion samples. 4 GHz sampling rates expose the finest details in your signals. 1 GHz Transitional sampling provides the optimum method to capture fast data bursts separated by seconds, minutes, or even hours of bus inactivity. The GoLogicXL State analysis can also synchronize with single-data-rate 300 MHz SDR clocks, and double-date-rate 250 MHz DDR clocks (500 MHz effective).
-
product
100MHz, 2 Channel PXI Oscilloscope, Spectrum Analyzer, Transient Recorder & Voltmeter
TE6100
The TE6100 is the first 100 MS/SEC measuring instrument that consists of a Digital Storage Oscilloscope, Spectrum Analyzer, Transient recorder and Voltmeter. This new PXI based, compact measuring instrument, can solve almost every measurement problem. Analyzing signals is done with an 8-bit resolution and a maximum sampling speed of 100 MHz. The input ranges 0.1 Volt full scale to 80 Volt full scale. The record length is 32K/64K samples.
-
product
WiFiScope WS6: 200 MS/s 250MHz BW, 4 Channel, Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
WS6-200XM-W5
*Oscilloscope / Spectrum analyzer / Voltmeter*14 bit (0.006 %) resolution (16 bit enhanced resolution)*200 MS/s sampling*250 MHz bandwidth*Up to 64 MSamples memory per channel*0.25 % DC vertical accuracy*1 ppm timebase accuracy*WiFiScope advantages
-
product
Digital Oscilloscope
MSO/DS2000A
The MSO/DS2000A series of digital oscilloscopes are universal digital oscilloscopes with bandwidths from 100MHz to 300MHz and sampling rates up to 2GSa/s, combined with deep memory depth and high waveform capture rates.
-
product
HandyScope HS5: 500 MS/s 250MHz BW, 2 Channel, USB Digital Storage Oscilloscope, 40MHz AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
HS5-540XM-W5
The Handyscope HS5 is the first USB oscilloscope (USB powered) sampling at 500 MHz, with a 14 bits resolution and a 250 MHz bandwidth. This makes it possible to analyze very fast signals with very small amplitudes. The smallest distortions can be revealed due to the high resolution and bandwidth. Because of the deep memory (up to 64 MSamples on one channel), long record measurements are available for intermittent phenomena and Fast Fourier Transform calculations with over 32 million spectral lines can be performed. Using very fast FFT algorithms, an FFT with 1 million spectral lines can be performed within a second.
-
product
8 Series Sampling Oscilloscope
The 8 Series Sampling Oscilloscope enables efficient and affordable optical component testing with an innovative disaggregated architecture. With a reconfigurable and compact design, an innovative user interface, and reliable high-end performance, this oscilloscope is an ideal test solution for manufacturing applications. The 8 Series is designed to adapt to a continuous increase in demand for higher bandwidths and baud rates addressing current and future test parameters.
-
product
TiePieSCOPE HS805, 2 Ch, 32MS/ch, 1 GS/s, 250MHz BW, USB Digital Storage Oscilloscope, AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
HS805
The TiePieSCOPE HS805 is a portable USB oscilloscope that combines a high sampling speed (1 GSamples/s on one channel, 500 MSamples/sec on two channels) with a long record of 32 MiSamples per channel. That allows you to capture long, complex signal patterns at full speed. The 250 MHz high bandwidth ensures that the signals are measured accurately and without distortion.
-
product
USB Oscilloscope
M520 Series
Oscilloscopes with bandwith from 60 to 150MHz and sampling rate from 50 to 200MS/s.
-
product
Digital Storage Oscilloscopes
SDS1000DL+ Series
SDS1000DL+ series is a dual-channel universal digital oscilloscope, available in 50 MHz, bandwidth models. It includes a 30 Kpts memory depth that helps to ensure accurate waveform resolution and to capture longer signal lengths. With its 7 inch TFT-LCD (800*480) screen, there is adequate screen space to help better see and analyze waveform details. Along with a 1 GSa/s sampling rate, the SDS1000CML+ supports 32 parameters measurements and common mathematical operations to speed up complex / repetitive measurements.
-
product
50MHz BW, 50MS/s, 2-Channel PC-based Digital Storage Oscilloscope (DSO)
PCS500AU
The PCS500AU is a digital storage oscilloscope that uses a computer and its monitor to display waveforms. All standard oscilloscope functions are available through the supplied Windows program. Its operation is identical to that of normal oscilloscope apart from the fact that all operations can be performed with the mouse. Connection is through the computer's parallel port and the scope is completely optically isolated from the computer port. The oscilloscope and transient recorder have two completely separated channels with a sampling frequency up to 1GHz. Any waveform displayed on the screen can be stored for later use in documents or for the comparison of waveforms.
-
product
Handheld Oscilloscopes, 100 MHz, 2 Analog Channels
U1610A
100 MHz2 analog channelsTroubleshoot in any weather with channel-to-channel isolation and a CAT III 600 V safety ratingIdentify glitches easily with dual window zoomView subtle signal details more clearly with up to 1 Gsa/s sampling rate and 120 Kpts memoryDebug under any lighting conditions with 3 selectable viewing modes (indoor, outdoor and night vision)Get 3 instruments in 1: a dual-channel oscilloscope, built-in DMM and data loggerEasier start-up with 10 selectable languages
-
product
Data Acquisition (DAQ) for R&D and Testing Applications
While Memory Hicorders don’t have sampling speeds that are as fast as those of digital oscilloscopes, these waveform recorders can be used to record various types of signals without worrying about potential differences between them and without using isolation amplifiers.
-
product
HandyScope HS5 + SureConnect: 200 MS/s 250MHz BW, 2 Channel, USB Digital Storage Oscilloscope, 20MHz AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
HS5-220XMS-W5
The Handyscope HS5 is the first USB oscilloscope (USB powered) sampling at 200 MHz, with a 14 bits resolution and a 250 MHz bandwidth. This makes it possible to analyze very fast signals with very small amplitudes. The smallest distortions can be revealed due to the high resolution and bandwidth. Because of the deep memory (up to 64 MSamples on one channel), long record measurements are available for intermittent phenomena and Fast Fourier Transform calculations with over 32 million spectral lines can be performed. Using very fast FFT algorithms, an FFT with 1 million spectral lines can be performed within a second.
-
product
Oscilloscope
MOSTS6
*MOSTS6 is the first Russian instrument (oscilloscope) with a direct sampling rate (8bit ADC), 5 Gigasemp / s per channel. M-module MOSTs6 is designed to work as a part of information measuring systems based on the VXI bus magister as a digital oscilloscope. The M-module is made in the form of a triple-width mezzanine, is installed on a mezzanine carrier and is connected to it via a local information highway.*MOSTS6 is designed to convert instantaneous voltage values of an electrical signal into a digital code, measure instantaneous voltage values, measure time intervals between two instantaneous voltage values through two independent channels.MOSC6, according to the conditions of use, meets the requirements for measuring instruments of group 3 in accordance with GOST 22261-94.
-
product
Dual-channel Digital Oscilloscope
ScopeDAQ
Dual-channel digital oscilloscope ScopeDAQ allows the user to capture the data with frequency 100MHz. Higher sampling frequency (200MHz) is available in case of using one channel. Basic version of the instrument is equipped with 128K data buffer, optionally it can be enlarged up to 512KB.
-
product
60 MHz USB Oscilloscope
522
The Dataman 522 is a dual channel oscilloscope with 60 MHz bandwidth and USB 2.0 connectivity • USB powered - no additional power supply is required • Dual channel with external trigger • 60 MHz bandwidth • 50 MS/s real time sampling rate • 5 GS/s equivalent sampling rate • 8,000 sample buffer per channel • Hi-speed USB 2.0 connectivity allowing fast and easy connection to PC’s and laptops • Comprehensive 2 years parts and labor warranty • Free life-time software updates
-
product
120 MHz USB Oscilloscope
524
The Dataman 524 is a dual channel oscilloscope with 120 MHz bandwidth and USB 2.0 connectivity • USB powered - no additional power supply is required • Dual channel with external trigger • 120 MHz bandwidth • 100 MS/s real time sampling rate • 10 GS/s equivalent sampling rate • 8,000 sample buffer per channel • Hi-speed USB 2.0 connectivity allowing fast and easy connection to PC’s and laptops • Comprehensive 2 years parts and labor warranty • Free life-time software updates
-
product
Portable Digital Oscilloscopes
GAO Tek offers a variety of Portable Digital Oscilloscopes with long lasting battery life and durable design. These Portable Digital Oscilloscopes have a wide range of real-time sampling rate from 72 MSa/s to 25GSa/s. These Portable Digital Oscilloscopes also have other functions integrated into them such as a digital multimeter and a frequency counter. These portable oscilloscopes are designed for the sciences, medicine, engineering and telecommunications industry.
-
-
product
USB Oscilloscope
Handyscope HS6 DIFF
This powerful USB 3.0 super speed oscilloscope combines fast sampling up to 1 GS/s with high resolutions of 12, 14 and 16 bit and a large memory of 64 MSamples on all four channels. The oscilloscope supports continuous streaming measurements up to 200 MS/s and can be synchronized with other oscilloscopes using the CMI interface to form a multi channel combined instrument with synchronized timebase. The CMI interface is available by default on the Handyscope HS6 DIFF. Optionally, the Handyscope HS6 DIFF can be delivered with SureConnect connection test and resistance measurement on each channel. Also, the Handyscope HS6 DIFF can be delivered with SafeGround option. With SafeGround you can switch the differential inputs of the Handyscope HS6 DIFF into single ended inputs with ground protection. It allows to make measurements using standard attenuating probes and protects the scope when a short circuit to ground is created.
-
product
WiFi Oscilloscope Probe
IkaScope
IkaScope is a wireless oscilloscope probe. It fits perfectly in your hand and works with any connected screen, like a laptop, a tablet or smartphone. Thanks to ProbeClick® technology, IkaScope knows when to measure and when to hold. IkaScope transfers measured signals over high speed wifi connection. 200 MSa/S Sampling rate. 30 MHz Bandwidth. 80 Vpp Input range. AC/DC Coupling. 4000 ptsMemory. 200 FPS Max. refresh rate.
-
product
Track and Hold Data
Track and hold amplifiers are used to expand the bandwidth and/or high-frequency linearity of high-speed A/D conversion and signal acquisition systems. Track and Hold Amplifiers can be used in various applications including RF ATE Applications, Digital Sampling Oscilloscopes, RF Demodulation Systems, Digital Receiver Systems, High Speed Peak Detectors, Software Defined Radio, Radar, ECM & ELINT Systems and High Speed DAC De-Glitching.
-
product
Digital Storage Oscilloscopes
SDS1000CML+ Series
SDS1000CML+ series is a dual-channel universal digital oscilloscope, available in 70, 100, and 150 MHz bandwidth models. It includes a 2 Mpts memory depth that helps to ensure accurate waveform resolution and to capture longer signal lengths. With its 7-inch TFT-LCD (800*480) screen, there is adequate screen space to help better see and analyze waveform details. Along with a 1 GSa/s sampling rate, the SDS1000CML+ supports 32 parameters measurements and common mathematical operations to speed up complex / repetitive measurements.
-
product
100MS/s 100MHz BW LPT/parallel Port 2-Channel Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder, AWG/Function Generator
HS801-AWG
The HS801: the first 100 MSPS measuring instrument that consists of an Arbitrary Waveform Generator/Function Generator, a Voltmeter, a Digital Storage Oscilloscope (DSO), a Spectrum analyzer, and a Transient Recorder. This new portable and compact measuring instrument can solve almost every measurement problem. Analyzing signals is done with 8-bit resolution and a maximum sampling speed of 100 MHz. The input range is 0.1 Volt full scale to 80 Volt full scale. The record length is 32K/64K samples.
-
product
DCA-M Sampling Oscilloscopes
Built on Keysight's digital communication analyzer (DCA) technology, the DCA-M family is recognized as the industry standard for verifying optical transmitter compliance to communications standards. With single to quad optical AND electrical channels in a compact form factor, the DCA-M is ideal for both manufacturing and RND applications. Analyze both multi-mode and single-mode signals with the low-noise, high-sensitivity calibrated reference receivers. The variety of models along with the supporting software and compliance applications ensure you can measure with high precision, whether you analyze electrical or optical devices.
-
product
Oscilloscopes
Anritsu sampling oscilloscope is an ideal solution for Eye pattern analyses and Eye Mask tests. In addition, The excellent performance and high sampling speed reduce measurement times and help hold-down equipment costs.
-
product
HandyScope HS5: 100 MS/s 250MHz BW, 2 Channel, USB Digital Storage Oscilloscope, 10MHz AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
HS5-110XM-W5
The Handyscope HS5 is the first USB oscilloscope (USB powered) sampling at 100 MHz, with a 14 bits resolution and a 250 MHz bandwidth. This makes it possible to analyze very fast signals with very small amplitudes. The smallest distortions can be revealed due to the high resolution and bandwidth. Because of the deep memory (up to 64 MSamples on one channel), long record measurements are available for intermittent phenomena and Fast Fourier Transform calculations with over 32 million spectral lines can be performed. Using very fast FFT algorithms, an FFT with 1 million spectral lines can be performed within a second.
-
product
150 MHz USB Oscilloscope
574
The Dataman 574 is a dual channel oscilloscope with 150 MHz bandwidth and USB 2.0 connectivity • USB powered - no additional power supply is required • Dual channel with external trigger • 150 MHz bandwidth • 100 MS/s real time sampling rate • 10 GS/s equivalent sampling rate • 1 MS sample buffer per channel • Hi-speed USB 2.0 connectivity allowing fast and easy connection to PC’s and laptops • Comprehensive 2 years parts and labor warranty • Free life-time software updates
