Filter Results By:
Products
Applications
Manufacturers
SPST
Single Pole Single Throw relay.
-
product
SIMRC - 16 x Uncommitted Reed Relay, SPST Screened
1010-R-16-1RF-5/1D
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
product
PXIe Power Relay Module, 12xSPST, 16 A, With Interlock
42-161A-002-HI
The 40/42-161A-002-HI is a PXI/PXIe 12xSPST power relay module with optional hardware interlock. It is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock.
-
product
PCI 32xSPDT Shielded Reed Relay Card
50-120-021
This of PCI switching cards are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female connector.
-
product
PXI 24 x DPST Reed Relays
40-115-122
Available in normally open (DPST & SPST) configurations. Connections are made via a front panel micro-D 96-pin male connector. For applications requiring improved bandwidth and crosstalk performance please look at our 40-120 and 40-125 range of shielded reed relay cards. General purpose reed relays are suitable for the construction of small switching networks, slaving up to larger switches or operating external devices (e.g. lamps, solenoids etc.). To simplify inter-relay wiring, interconnection points are built onto the circuit board easing the construction of complicated wiring.
-
product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 16.3k Ohm - SPST
40-294-131
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Serial to Relay Minibox™
Model 2364
* Model 2364-11 provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Optional 1 'U' high Rack Mounting Kits hold one or two 2364s.* Includes 50-pin mating connector for solder connections.* Optional 1 'U' high Rack Mounting Kits hold one or two 2364s.* Optional 115750 Terminal Board and Terminal Strip for easy connections without soldering. See the Serial Accessory page.
-
product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 65.5k Ohm - SPST
40-294-133
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI 48 x SPDT Reed Relays
40-143-121
The 40-140A/141/143 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector.
-
product
PXI/PXIe Power Relay Module, 8xSPDT, 5 Amp, 37-Pin D-type Connector
40-158-104
The 40/42-158-104 is a PXI/PXIe high density power relay module with 8xSPDT switches rated at 5A. User connection is via a 37-pin D-type male connector. The 40/42-158 range is available in 8, 16, 24 or 32 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
product
PXI/PXIe Power Relay Module, 24xSPDT
40-158-002-HI
The 40/42-158-002-HI is a PXI/PXIe high density power relay module with 24xSPDT switches rated at 5A and includes the hardware interlock option. User connection is via 2x50-pin SGMC male connectors, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied). The 40/42-158 range is available in 8, 16, 24 or 32 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
product
PXI Programmable Resistor Module 2-Channel 3 Ohm to 131k Ohm - SPST
40-294-134
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXIe Power Relay Module, 10xSPST, 16 A
42-161A-003
The 40/42-161A-003 is a PXI/PXIe 10xSPST power relay module and is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock.
-
product
LXI Optical Switching - 5x5 Matrix Plugin Module
65-280-322
The 65-280-322 5x5 matrix is part of the 65-280 and 65-281 ranges of optical plug-in modules offering matrix & insert/bypass or multiplexer & SPST topologies respectively with all models based on MEMS fiber optic switches and available in various populations per plugin. In addition, a choice of different connector styles to suit most applications is offered: FC/APC (for optimal performance), FC/PC, SC/PC and ST for general applications and LC for high density applications. They use MEMS (Micro-Electro-Mechanical-Systems) based optical switches to route signals between terminals by redirecting the optical signal. This is achieved using micromechanical mirrors driven by a highly precise mechanism activated via an electrical control signal.
-
product
PXI/PXIe High Density Electro-mechanical Relay Module, 64xSPDT
40-148A-201
The 40-148A-201 (PXI) and 42-148A-201 (PXIe) 64xSPDT relay module is part of a range of high density switching modules available in Normally Open (SPST & DPST), Changeover (SPDT) and Normally Closed (SPST) configurations. Connections are made via a front panel 200-pin female connector.
-
product
PXI 25 x SPST Reed Relay 2.5 Amp
40-136-111
Pickering Interfaces 40-136 Power Reed Relay Modules are suitable for applications where ordinary reed relay modules require additional current/voltage capacity. The 40-136 is suitable for voltages to 200V and current to 2.5A. Available in Normally Open (SPST & DPST) configurations. Connections are made via a front panel mounted 50 or 78-pin D-Type connector.
-
product
PXIe Power Relay Module, 10xSPST, 16 A, With Interlock
42-161A-003-HI
The 40/42-161A-003-HI is a PXI/PXIe 10xSPST power relay modulewith optional hardware interlock. It is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock.
-
product
PXI 16 x SPDT Reed Relays
40-110-021
The 40-110/115 range of switching modules are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 96 pin male micro-D connector. General purpose reed relays are used for the construction of small switching networks or for slaving up to larger switches.To simplify inter-relay wiring, interconnection points are built onto the circuit board thus easing the construction of complicated wiring.
-
product
PXI/PXIe High Density Reed Relay Module, 50xSPST
42-140B-021
The 40-140B-021 (PXI) and 42-140B-021 (PXIe) are 50xSPST general purpose switching modules. They are part of a range of high density relay modules using ruthenium reeds available in 50x, 75x and 100x Normally Open SPST configurations. Connections are made via a front panel 200-pin female connector.
-
product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 16.3k Ohm - SPST
50-294-131
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
LXI Optical Switching - 2:1 Multiplexer Plugin Module
65-281-381
The 65-281-381 2:1 multiplexer is part of the 65-280 and 65-281 ranges of optical plug-in modules offering matrix & insert/bypass or multiplexer & SPST topologies respectively with all models based on MEMS fiber optic switches and available in various populations per plugin. In addition, a choice of different connector styles to suit most applications is offered: FC/APC (for optimal performance), FC/PC, SC/PC and ST for general applications and LC for high density applications. They use MEMS (Micro-Electro-Mechanical-Systems) based optical switches to route signals between terminals by redirecting the optical signal. This is achieved using micromechanical mirrors driven by a highly precise mechanism activated via an electrical control signal.
-
product
80/24 Channel SPST Plug-in Switch Card
1260-118/118A
The Astronics 1260-118/118A is an 80/24-channel, SPST (Form A) plug-in relay card for the Adapt-a-Switch™ platform.
-
product
8-Ch SPST 20A-250VAC High Current
YAV90087
8 power relays Switching 20A 250Vac PNP Outputs para control or YAV90304 control CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
PXI/PXIe Power Relay Module, 32xSPDT, 5 Amp, 50-Pin SGMC Connectors
40-158-001
The 40/42-158-001 is a PXI/PXIe high density power relay module with 32xSPDT switches rated at 5A. User connection is via 2x50-pin SGMC male connectors. The 40/42-158 range is available in 8, 16, 24 or 32 SPST configurations with or without hardware interlock.
-
product
PXI/PXIe High Density Electro-mechanical Relay Module, 100xSPST, Normally Open
40-145A-201
The 40-145A-201 (PXI) and 42-145A-201 (PXIe) 100xSPST relay module is part of a range of high density switching modules available in Normally Open (SPST & DPST), Changeover (SPDT) and Normally Closed (SPST) configurations. Connections are made via a front panel 200-pin female connector.
-
product
PXI Solid-State Switch Module, 3xSPST, 25 A, 100 V, Hardware Interlock
40-184A-002-HI
The 40-184A-002-HI has 3-off high current SPST switches with hardware interlock in one PXI slot and is part of our range of high power solid state switching solutions.
-
product
E & W-Band PIN Diode Waveguide Switches
Fairview Microwave’s single-pole single-throw (SPST) and double-pole double-throw (DPDT) PIN diode waveguide switches feature fully integrated WR-10 and WR-12 waveguide ports and cover popular E-band (60 to 90 GHz) and W-band (75 to 110 GHz) frequencies. Switch circuits integrate low loss Fin-line assemblies with high performance GaAs beam-lead diodes that results in 4 dB insertion loss, greater than 25 dB of Isolation and fast switching speed < 300 nsec.
-
product
PXI 32 x SPST Reed Relay 2 Amp
40-136-211
Pickering Interfaces 40-136 Power Reed Relay Modules are suitable for applications where ordinary reed relay modules require additional current/voltage capacity. The 40-136 is suitable for voltages to 200V and current to 2.5A. Available in Normally Open (SPST & DPST) configurations. Connections are made via a front panel mounted 50 or 78-pin D-Type connector.
-
product
PXI/PXIe Power Relay Module, 36xSPST, 5 Amp, 50-pin SGMC Connectors
40-153-002
The 40/42-153-002 is a PXI/PXIe high density power relay module with 36xSPST switches rated at 5A. User connection is via 2x50-pin SGMC male connectors. The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
product
PXI 40Amp 14Volt 2xSPST Automotive Relay
40-180-001
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDCThe 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
-
product
PXI/PXIe Power Relay Module,5 Amp, 50-pin D-type Connector
40-153-103-HI
The 40/42-153-103-HI is a PXI/PXIe high density power relay module with 25xSPST switches rated at 5A and includes the hardware interlock option. User connection is via a 50-pin D-type male connector, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied). The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock.
