Filter Results By:
Products
Applications
Manufacturers
S-Parameters
Scattering Parameters quantifies high frequency RF power waves propagation through a network.
See Also: Vector Network Analyzers
-
product
Vector Network Analyser
LA19-13-02
The LA19-13-02 is a PC-driven Vector Network Analyser suitable for measuring a wide range of devices from 3 MHz to 3 GHz with 100 Hz resolution. Its full s-parameter test set includes bias-Ts for biasing active devices. It is housed in a small lightweight package making it very portable.
-
product
FieldFox C Handheld Microwave Analyzer, 6.5 GHz
N9914C
Capture elusive signals with up to 120 MHz gap-free, real-time bandwidth. Measure all four S-parameters simultaneously with 115 dB dynamic range. Make accurate spectrum analyzer measurements (± 0.3 dB) without warmup. Perform over-the-air measurements for 5G NR and LTE. Use GPS/GNSS for geolocation and timestamping.
-
product
Complex System Solutions
К2М-100 Series
*Operating Frequency Range: 100 MHz*Measurements per Connection*All S-Parameter Measurement (256 states)*SOLT Calibration*Measurement Profile Save*Full and Cross Measurement Result Analysis
-
product
FieldFox Handheld RF Vector Network Analyzer
N9923A
4/6 GHz max frequency Carry the world's most accurate handheld RF T/R VNA analyzer Expand capabilities with optional 2-port VNA, time-domain, vector voltmeter, cable and antenna analyzer and more Save time by simultaneously measuring all four S-parameters (S11, S21, S12, S22) with a single connection Perform accurate testing with QuickCal, full 2-port unknown thru Cal, TRL Easily measure average and puls
-
product
S-Parameter Measurement System
DPS08
KEYCOM provides S-parameter method measurement systems in two modes, the reflection mode and the transmission mode, to address the individual purposes. Both modes measure the complex permittivity (εr) and complex permeability (μr) at the same time, and the proper usage is as follows.
-
product
RF/Microwave Test Capability
Teledyne Labtech have extensive microwave alignment and microwave testing facilities. This includes the ability to test noise figure, S-parameters and harmonics. This ensures that Teledyne Labtech can supply a fully compliant product and provide a complete turnkey microwave assembly and test solution.
-
product
Automated Measurement Expert (AMX), VNA Plugin
S94702A
The Keysight automated measurement expert (AMX) is a smart software solution for automated multiport S-parameter measurements with the PXIe vector network analyzers M937xA/M9485A or the benchtop E5080A ENA network analyzer. The S94702A AMX VNA plugin adds S-parameter measurement capabilities to the Keysight test automation platform (TAP). The combination of the TAP and the VNA plugin forms the AMX backend software, which makes the VNA setups and executes the test sequences in the PXIe controller according to the optimized test sequence files generated by the AMX test plan builder. Other instrument plugins allow you to control the DUT mode, expand the number of test ports with the PXI switches or multiport test set, and use external instruments such as a DC power supply and a digital multimeter. The AMX backend software also provides step-by-step calibration wizard for full multiport calibration using the 4-port ECal module.
-
product
Network Analyzers
A network analyzer is an instrument used to analyze the properties of electrical networks, especially those properties associated with the reflection and transmission of electrical signals known as scattering parameters (S-parameters). Network analyzers are used mostly at high frequencies; operating frequencies can range from 9 kHz to 110 GHz
-
product
Active Hot Parameters
S93110B
S93110B active hot parameters is available on PNA-X Series network analyzers (N524xB) and provides more accurate method to test hot S-parameters, gain and output power, etc. than traditional methods by utilizing X-parameter technologies.
-
product
Handheld Vector Network
ZNH
R&S®ZNH is a full two-port handheld vector network analyzer that offers one-port cable and antenna measurement and full two-port S-parameter measurements. The touch based interface is simple to operate and a configuration overview menu makes measurement preparation more efficient. The R&S®ZNH may have a small form factor but it is complete in every detail and delivers high performance and all the key functionalities.
-
product
Active Hot Parameters For M98xxA PXIe VNA
S95111B
S95111B active hot parameters are available on M98xxA PXIe vector network analyzers and provide a more accurate method to test hot S-parameters, gain, and output power than traditional methods by utilizing X-parameter technologies. Restricted to 50 GHz.
-
product
FieldFox Handheld Microwave Analyzer, 26.5 GHz
N9918A
26.5 GHz max frequency Carry the world's most integrated handheld analyzer: standard model includes cable and antenna analyzer Expand capabilities with optional VNA, spectrum analyzer, built-in power meter, vector voltmeter, and more Save time by measuring DTF and TDR in the same sweep Simultaneously measure all four S-parameters Make accurate spectrum analyzer measurements ( 0.5 dB) without needing warm-up Calibrate simply with QuickCal
-
product
PNA Microwave Network Analyzer
N5221B
Meet your toughest measurement challenges with the highest performing microwave network analyzer in the industry Measure S-parameters with the smallest uncertainty and highest stability Efficiently characterize active components with applications that simplify setups Meet your specific budget and measurement needs by customizing to just the right level of performance Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
product
110 GHz Lightwave Component Analyzer
N4372E
The N4372E lightwave component analyzer helps you with optoelectronic tests with its measurement capability of 110 GHz in an extended wavelength range. It also offers RX testing up to 110 GHz in the full 1260 nm to 1620 nm range. It has a built-in optical power meter that enables you to check and control the operating power. The N4372E lightwave component analyzer's optical transmitter input port connects to an auxiliary tunable laser to verify S-parameters over wavelength.
-
product
Vector Network Analyzer (VNA) Simulator – Advanced
S94051B
S94051B puts Keysight’s industry-leading network analyzer software portfolio into your computer. Dive deeper into data captured on an instrument with support for time domain, spectrum analysis, gain compression, and all the other software applications you use on your instrument. You can also develop and troubleshoot test programs on your computer before deploying them to the instrument. S94051B is a superset of S94050B and contains the S-parameter functionality.
-
product
PNA-L Microwave Network Analyzer
N5232B
Perform basic analysis of passive components and simple active devices Measure S-parameters with good accuracy up to20 GHz in cost-sensitive applications Get the world's best price-to-performance ratio for microwave manufacturing Configure an economical solution for signal-integrity measurements and materials characterization Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
product
High Dynamic Receivers
ZRX
converter series with high dynamic range receivers. Typical applications are antenna measurements (OTA) and signal analysis. The ZRX Receivers are used wherever full S-parameters are not required.
-
product
FieldFox Handheld RF Analyzer, 6.5 GHz
N9914A
6.5 GHz max frequency Carry the world's most integrated handheld RF analyzer: standard model includes cable and antenna analyzer Expand capabilities with optional VNA, spectrum analyzer, built-in power meter, vector voltmeter, and more Save time by measuring DTF and TDR in the same sweep Simultaneously measure all four S-parameters Make accurate spectrum analyzer measurements ( 0.5 dB) without needing warm-up Calibrate simply with QuickCal
-
product
26.5 GHz Single-Mode Lightwave Component Analyzer
N4375E
The new N4375E single-Mode LCA is based on the latest 5222A series network analyzers with 2-port or 4-port configuration. This LCA is the ideal measurement solution for electro-optical components up 26.5GHz electro-optical components, as well as Radio over Fiber (RoF) and aerospace and defense (A&D) electro-optical test applications. The N4375D is traceable to international standards and provides guaranteed specifications for electro-optical responsively S-parameter measurements in a turn-key solution. In combination with N4691B electronic calibration kit you get fastest setup of your test, so you can focus on developing your components. The new N4375D replaces the industry standard 8703A/B series and supports specified modulation frequencies up to 26.5 GHz at 1310nm and 1550nm source wavelength or individual wavelength with external optical input.
-
product
Active Hot Parameters For E5081A ENA-X And E5080B ENA
S96111B
The S96111B active hot parameters are available on ENA-X or ENA network analyzers and provide a more accurate method to test hot S-parameters, gain and output power than traditional methods by utilizing X-parameter technologies. Restricted to 50 GHz.
-
product
Metrology
Rosenberger Hochfrequenztechnik GmbH & Co. KG
Network analyzers are used to measure so-called scatter parameters (S-parameters). These describe the behaviour of electrical components with the help of wave magnitudes. Whether simple cables, filters, amplifiers or complex subsystems, the following applies to all these components: Different loads can have unseen effects on the measured values over time.
-
product
Real-time S-Parameter And Power Measurement Uncertainty
S95015B
The S95015B provides real-time measurement uncertainty for S-parameters and power measurements with the measurement traces on one screen. It lets you estimate uncertainty reliably and apply more realistic limit lines for pass/fail tests for better production yield rates.
-
product
FieldFox Handheld Microwave Analyzer, 50 GHz
N9952A
50 GHz max frequency Carry industry's first 50 GHz handheld W analyzer: standard model includes cable and antenna analyzer Expand capabilities with optional VNA, spectrum analyzer, built-in power meter, vector voltmeter, and more Save time by measuring DTF and TDR in a single sweep Simultaneously measure all four S-parameters Make accurate SA measurements ( 0.5 dB) without needing warm-up Easily measure average and pulse power with a USB sensor
-
product
FieldFox Handheld Microwave Vector Network Analyzer
N9926A
14 GHz max frequency Carry the world's most integrated handheld T/R VNA analyzer Expand your measurement flexibility with optional 2-port VNA, time-domain, vector voltmeter, cable and antenna analyzer and more Save time by simultaneously measuring all four S-parameters with a single connection Perform accurate testing with QuickCal, full 2-port unknown thru Cal, TRL Easily measure average and pulse power with a USB power sensor
-
product
Real-time S-Parameter And Power Measurement Uncertainty
S93015B
The S93015B provides real-time measurement uncertainty for S-parameters and power measurements with the measurement traces on the same screen. It enables the users to estimate more reliable uncertainty and apply more realistic limit lines for pass/fail tests for better production yield rates.
-
product
Fast Electromagnetic Analysis Suite
FEMAS
FEMAS was created to provide tools for engineers to assist in PCB and system design. Our tools are based on full wave solutions to Maxwell's equations but operate much faster than traditional CEM tools. Multi-Functional! End-to-End Link Path Analysis. S-parameter file concatenation. Time Domain analysis. Frequency Domain analysis. Transmit/Receive Equalization. Causality/Passivity Checking/enforcement. 2D Cross Section Analysis for multi-conductors. S-parameter and waveform plotting. Network parameter conversion. De-Embedding. Signal Analysis.
-
product
PNA-L Microwave Network Analyzer
N5239B
Perform basic analysis of passive components and simple active devices Measure S-parameters with good accuracy up to8.5 GHz in cost-sensitive applications Get the world's best price-to-performance ratio for microwave manufacturing Configure an economical solution for signal-integrity measurements and materials characterization Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
product
Automated Measurement Expert (AMX), Test Plan Builder
S94701A
The Keysight S94701A automated measurement expert (AMX) Test Plan Builder will help you edit and create your test plans for automated multiport S-parameter measurements with the PXI Vector Network Analyzer (VNA).
-
product
Predicting Microwave and RF Designs Virtually
RF Module
The RF Module is used by designers of RF and microwave devices to design antennas, waveguides, filters, circuits, cavities, and metamaterials. By quickly and accurately simulating electromagnetic wave propagation and resonant behavior, engineers are able to compute electromagnetic field distributions, transmission, reflection, impedance, Q-factors, S-parameters, and power dissipation. Simulation offers you the benefits of lower cost combined with the ability to evaluate and predict physical effects that are not directly measurable in experiments.
-
product
Automotive Ethernet Rx Compliance Software
AE6910R
Unlike CAN, LIN, or MOST, the IEEE standard for automotive Ethernet demands rigorous compliance verification using specific test cases. The test requirements include complex measurements: vector network analysis with S-parameters, bit error rate (BER) test, and protocol analysis of high-speed digital signals.
