Filter Results By:
Products
Applications
Manufacturers
-
product
Programmable AC Laboratory Power Supplies, Current-controlled
*Fast regulation of the current*Voltage depends on the load*Current and voltage values are configured based on the customer's actual requirements*Power from 250VA to 36kVA*Output voltages 1VAC to 300VAC*Maximum currents up to 2000A per phase
-
product
Programmable Bidirectional AC Laboratory Power Supplies (source / Sink)
Programmable Bidirectional AC Laboratory Power Supplies (source / Sink)
-
product
6U Power Supply Mainframe
GX7400A
The GX7400A is a dual output programmable DC power supply designed for use in 6U PXI systems. The GX7400A occupies three slots and is controlled via the PXI bus. The AC power is provided using a panel-mounted receptacle. The power supplies are fully isolated and can be externally connected in series to provide higher voltage.
-
product
AC Power Supplies & Frequency Converters
Behlman manufactures a broad line of AC Power supplies and Frequency converters with available power from 1,000 VA to 120,000 VA in both single-phase and three-phase output. Available with variable or fixed voltage and frequency output, manual or programmable control, with a variety of interfaces, unique protection circuitry and the ability to modify units for your application.
-
product
PXI-2565, 16-Channel, 7 A, SPST PXI Relay Module
777754-01
16-Channel, 7 A, SPST PXI Relay Module—The PXI‑2565 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. It delivers high-current switching of DC power supplies, AC line power, and AC/DC current sources. The PXI‑2565 is fully software programmable and supports multiple instrument synchronization.
-
product
Programmable AC Laboratory Power Supplies, Motor-controlled
Programmable AC Laboratory Power Supplies, Motor-controlled
-
product
High Performance Programmable AC Power Supply
IT7600 Series
IT7600series high performance programmable AC power supplies, adopt advanced digital signal processing technology, with frequency up to 10-5000 Hz, built-inall-round power meter and large-screen oscilloscope function. Power up to 54kVA and support master-slave parallel, which can provide high-capacity single-phase or three-phase AC output.
-
product
3-Phase AC Power Source
61700 series
The Chroma Programmable AC Power Source model 61700 series delivers pure, 5-wire, 3-phase AC power. Unlike the traditional 3-phase AC power source, it includes low power rating models at very low cost. Users can program voltage and frequency, measure the critical characteristics of the output on its LCD display. It delivers the right solution to simulate all kinds of input condition of UUT to be utilized in R&D and QA. It is also suitable for commercial applications from laboratory testing to mass productions. The 61700 supplies the output voltage from 0 to 300VAC and it can be set individually for each phase. Users also can set the phase angle from 0? to 360?. These kinds of function make the 61700 series can simulate unbalance 3-phase power. Because of the wide output frequency from 15 to 1200Hz, it is suitable for avionics, marine and military application. The AC+DC mode extends the output function to simulate abnormal situation when power line contains DC offset.
-
product
High Performance Programmable AC Power Supply
IT-M7700 Series
ITECH newly-launched IT-M7700 High Performance Programmable AC Power Supply combines intelligence and flexibility, breaks through the huge defects of the traditional AC power source, reduces the size to only 1⁄2 1U, maximizes space utilization. Built-in power meter and arbitrary waveform generator make it convenient to simulate various arbitrary waveform outputs. IT-M7700 is designed with advanced technologies of programmable AC and DC power supplies, and can be widely used in multiple fields such as power energy products, home appliances, industrial electronics, avionics, military and IEC standards testing.
-
product
Programmable AC Laboratory Power Supplies Linear
Programmable AC Laboratory Power Supplies Linear
-
product
6U Power Supply Mainframe. Accepts Two Programmable Power Modules
GX7400A
The GX7400A is a dual output programmable DC power supply designed for use in 6U PXI systems. The GX7400A occupies three slots and is controlled via the PXI bus. The AC power is provided using a panel-mounted receptacle. The power supplies are fully isolated and can be externally connected in series to provide higher voltage.
-
product
150-Watt AC/DC Power Supply; Single Output
56MS1
NAI’s 56MS1 is a 150 Watt AC/DC Power Supply that accepts multiple AC inputs plus a +270 VDC input. This COTS unit provides full-power, single output, at a baseplate temperature of +85° C.
-
product
PXI Device Power Supply - 4 Isolated Channels, 20-bit Measurement Resolution
52310e series
Chroma 52310e Series i s a programmabl e PXI-Express DPS (Device Power Supply) Card designed for high-accuracy and reliable output power for device test applications. Its compact size, easy level of integration, and high flexibility make the 52310e Series ideal for multi-channel power supplies. Chroma 52310e Series features 8 selectable control bandwidths to ensure high speed output and stable operation; multiple current measurement ranges with a 20-bit DAC/ADC provide the highest resolution and accuracy with a sampling rate up to 600K S/sec; programmable internal series resistance for battery simulation. Chroma 52310e DPS series has a patented hardware sequence engine that has deterministic t iming to cont rol each DPS channel. The sequencer's on-board memory can store up to 1024 sequencer commands and 32k measurement samples per channel.
-
product
PXI-4130, ±20 V, ±2 A DC, 40 W PXI Source Measure Unit
779647-31
±20 V, ±2 A DC, 40 W PXI Source Measure Unit - The PXI‑4130 is a programmable source measure unit (SMU). It has a single isolated SMU channel that offers a four-quadrant output that incorporates remote (4‑wire) sense. With its five current ranges, it is ideal for transistor characterization that requires accurately sourcing a constant current or voltage while sweeping another current. The PXI‑4130 also includes a utility channel that can source either current or voltage. This PXI SMU can act as either a constant voltage source or a constant current source, with a settable compliance limit for either mode. In addition, you can enable remote sense on the SMU channel to maximize voltage output and measurement accuracy on your device under test (DUT) for high-precision applications.
-
product
PXIe-4154, 2-Channel, 8 V, 3 A PXI Programmable Power Supply
781155-01
2-Channel, 8 V, ±3 A PXI Programmable Power Supply—The PXIe‑4154 is a specialized programmable power supply for battery simulation. It is designed to simulate a lithium‑ion battery cell’s transient speed, output resistance, and 2‑quadrant operation (source/sink). Critical to many RF and wireless applications, the simulator’s fast transient response time allows it to rapidly respond to changes in load current with minimal voltage dip, which makes the PXIe‑4154 ideal for powering devices under test (DUTs) such as RF power amplifiers, cellular handsets, and a variety of other mobile devices. To model the behavior of a battery more accurately, you can use the onboard programmable output resistance to simulate a battery’s internal resistance. For quiescent and standby current measurements, the PXIe‑4154 features integrated current measurement.
-
product
25-Watt AC/DC Power Supply
Model 56GS1
NAI’s 56GS1 is a 25 Watt AC/DC Power Supply that accepts multiple AC inputs plus a +270 VDC input. This COTS unit provides a single full-power output at a baseplate temperature of +85° C.Standard features include remote error sensing; remote digital (TTL) turn on/off; and protection against transients, overvoltage, overcurrent, and short-circuits. Options such as ESS vibration testing and choice of output voltages are available, and additional options and special units can be ordered.
-
product
2,000 Watt AC/DC Standalone EMI Compliant Power Supply
56XS1
NAI’s 56XS1 is a conduction-cooled, 2,000 Watt AC/DC Power Supply that converts either 3-phase, AC input or +270 VDC input into a single DC output at 2,000 Watts.
-
product
PXI-4110, 3-Channel, 20 V, 1 A, 9 W, PXI Programmable Power Supply
779647-10
3-Channel, 20 V, 1 A PXI Programmable Power Supply—The PXI‑4110 is a programmable DC power supply. It is an excellent general-purpose, single-quadrant power supply for design validation and manufacturing test applications. The PXI‑4110 has two isolated and a single non-isolated supply channel, all capable of generating up to 1 A per channel. You can program the voltage setpoint and current limit as well as the voltage and current readback/measurement functionality. You can also combine channels for higher voltage or current.
-
product
Optical Power Meter - MATRIQ
Power 1400 Series
The Power 1400 Series optical power meter provides fast monitoring of signal power from -60 to +10 dBm and broad wavelength range of 750 to 1700 nm. With a logarithmic amplifier, it avoids gain-jumps faced by multi-stage linear amplifier power meters.
-
product
3U CompactPCI 8HP 16.6-160VDC Input Railway Power Module
cPS-H325/WDC
- PICMG® 2.11 CompactPCI® Power Interface compliant- 16.6 to 160VDC wide input range, 310W- 3U, 8HP CompactPCI package- EN 50155 Class S2 and C2 compliant for power stability- 40°C to 85°C operating temperature with deratin*g
-
product
cPCI Power Supply
VX6625
The potential-free power supplies of the VX66xx family stand for precision and reliability and are characterized by many extras such as extremely low noise, very short rise and fall times and additional measurement functions. The energy is completely provided by the PXI chassis, therefore external power supplies are not necessary.
-
product
1,000 Watt AC/DC (High Voltage Output) Power Supplies
56XS2
NAI’s 56XS2 is a conduction-cooled, 1,000 Watt AC/DC Power Supply that converts a 3-phase, AC input into a single HIGH VOLTAGE +270 VDC output at 1,000 Watts.
-
product
Power Monitor, AC-Powered
PMA/PQA
NAI's PMA and PQA Power Monitors are used to monitor voltage, frequency, and phase characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power line characteristics are within predetermined limits. These power monitors are ideally suited for rugged defense and industrial applications.
-
product
Power, Patchcord, ITA, Mini Power, 36", 14 AWG White Teflon, Single Ended, (30 Amps)
7-241914000-036
Power, Patchcord, ITA, Mini Power, 36", 14 AWG White Teflon, Single Ended, (30 Amps).
-
product
Power, Patchcord, Receiver, 72", Micro Power, 14 AWG White, Single Ended ( 22 Amps)
7-252914000-072
Power, Patchcord, Receiver, 72", Micro Power, 14 AWG White, Single Ended ( 22 Amps).
-
product
PICMG 2.11 47-Pin Hot-Swap Redundant 3U CompactPCI 8HP 250 W Power Module
cPS-H325/AC
- PICMG® 2.11 CompactPCI® Power Interface compliant- 3U CompactPCI® 8HP form factor- PICMG® 2.11 47-pin CompactPCI® in-rack power module interface- 250 W DC output
-
product
FPD Tester Power Module
67393-120-480
The 67393-120-480 FPD Tester Power Module is a new generation of small, stable, high reliability AC to DC power supply. It adopts compact mechanical design and uses Chroma FPD Tester for signal input/output that can provide a total solution for testing the signal, control and power of diversified panels.
-
product
Industrial Flex ATX AC Power Supply for Mini-ITX Chassis, 250W
APS-925XU (80Plus)
- Power (typical): 250W- AC Voltage Input Range: Universal- Certifications: UL/cUL/TUV/CCC- Dimensions: 150 x 81.5 x 40.6 (mm)
-
product
Power, Patchcord, ITA, 72", Micro Power, 14 AWG White, Single Ended ( 22 Amps)
7-251914000-072
Power, Patchcord, ITA, 72", Micro Power, 14 AWG White, Single Ended ( 22 Amps).
-
product
High-density Optical Power Meter.
Power-1410
Quantifi Photonics’ Power-1410 optical power meter provides fast monitoring of signal power from -60 to +10 dBm and broad wavelength range of 1250 to 1650 nm. It provides unrivalled channel density with up to 288 parallel channels in a single 1U rack-mountable instrument.
