Filter Results By:
Products
Applications
Manufacturers
Photo Mask
-
product
Tabletop Mask Aligner
Model 200
The OAI Model 200 Mask Aligner is a cost-effective high performance mask Aligner that has been engineered with industry proven components that have made OAI a leader in the photolithography capital equipment industry. The Model 200 is a tableop mask Aligner that requires minimal cleanroom space. It offers an economic alternative for R&D, or limited scale, pilot production. Utilizing an innovative, air bearing / vacuum chuck leveling system, the substrate is leveled quickly and gently, for parallel photo mask alignment and uniform contact across the wafer during contact exposure. The system is capable of one micron resolution and alignment precision.
-
product
Tabletop Front & Backside Mask Aligner
Model 200IR
The OAI Model 200IR Mask Aligner is a tabletop system that requires minimal clean room space. It is a cost-effective alternative for R&D or limited scale, pilot production. Utilizing an innovative, air bearing / vacuum chuck leveling system, the substrate is leveled quickly and gently, for parallel photo mask alignment and uniform contact across the wafer during contact exposure. The Model 200IR Mask Aligner is capable of one micron resolution and alignment precision. It has an alignment module which features mask insert sets and quick-change wafer chucks that enable the use of a variety of substrates and masks without requiring tools for reconfiguration. The alignment module incorporates micrometers for X, Y, and z-axis.
-
product
Photo Detectors
Our photo detectors are offered for both power or energy measurements. Measure as low as a few femtojoules in energy or a few picowatts in power, thanks to our highly sensitive sensors and performant electronics.
-
product
Phase Masks
Phase masks are the production tool used to write gratings in fibers and waveguides. Ibsen Phase masks incorporate unbeatable, interferometric (holographic) patterning technology into a production friendly Phase mask.
-
product
MASK DR-SEM
Our defect review SEM tools perform detailed reviews of minute defects on photomasks.
-
product
Bounded Output Mask
The bounded output mask provides a means of ensuring that measurements of TI according to IEC 62359 can satisfy the requirement of only determining the ultrasonic output through an area of 1 cm x 1 cm.
-
product
Custom Solutions for Mask Aligners
OAI offers custom designed solutions built to your unique specification.
-
product
PHOTO COUPLER TESTER
May be linked to machine handler for automatic test on production line.Test items include：VF、IR、Vceo、Iceo、Vsat、CTR
-
product
Mask Treatment Process
Model 100MT
OAI offers a unique process which extends the life of your mask, says good bye to tedious washing and drying of mask and thus enables your mask aligner to have increased productivity at the lowest cost of ownership. The Model 100 MT is a 2 step process.
-
product
DUV Mask Aligner
Model 200E
OAI’S Model 200E DUV Mask Aligner performs all the functions of the tabletop Model 200 Mask Aligner but utilizes a 185nm Excimer Lamp as the UV light source. It is used for Biotechnology Processing.
-
product
Photo Gate Logger Sensor
NUL-209
This sensor can be used to study various kinds of motion. With six modes of operation, time, velocity or acceleration can be measured with one or two photo gates and associated timing cards, as well as showing pictorially the status (digital 1 or 0) of the voltage output of the photo gate as timing cards pass through it.
-
product
Large Photo Signal Generator
DDS9m
170MHz 4-Channel Signal Generator. The DDS9m generates four independent, phase synchronous sine wave output signals and is programmable in 0.1Hz steps from 0.1Hz to 171MHz. Programming is via an RS232 serial interface. Phase is 14-bit programmable and amplitude is 10-bit programmable. The DDS9m is accurate to 1.5ppm when using the on board TCXO timebase or you can use an external timebase. It requires 3.3 VDC power. SOF8_409 windows software is available as an extra cost accessory.
-
product
MRM(Mask)
MRM Series
- Fully automated system that can produce masks by automating the mask production process such as fabric supply, molding, cutting, and bonding.
-
product
Masks Bacterial Filtration Efficiency Tester
Sataton Instruments Technology CO., Ltd
Face Masks bacterial filtration efficiency BFE tester is to determine the bacterial filtration efficiency (BFE) of medical face mask materials by employing a ratio of the upstream bacterial challenge to downstream residual concentration of the tested medical face mask materials. The tester provides certain flow rate of bacterial aerosol. The operator can measure the number of colony forming units passing through the medical face mask material, which is clamped between a six-stage Anderson cascade impactor and an aerosol chamber, expressed as a percentage of the number of colony forming units present in the challenge aerosol.
-
product
Front & Backside, Semi-Automatic Mask Aligner
Model 800E
The OAI Model 800E front and backside, semi-automatic mask aligner system offers advanced features and specifications found most often in costly automated production mask aligners. With the development of this mask aligner, OAI meets the growing challenge of the dynamic semiconductor and MEMS market with a new class of mask aligners that are engineered for R&D and low volume production.
-
product
Masks Respiratory Resistance Tester
WKS-1200
WKS-1200 Masks Respiratory Resistance Tester applies to determining the inhalation resistance and exhalation resistance of respirators and mask protective products under specified conditions, and used for the relevant testing and inspection of ordinary mask products by the national labor protection equipment inspection agency or manufacturer.
-
product
Reticle / Mask Particle Detection System
PR-PD2HR
In semiconductor plants, where high performance and demanding functionality are required, the HORIBA PD Series'' high operating rate and long-term dependability have earned it a solid reputation. Inheriting a transfer system that has proven to provide stable, high performance and superior throughput over long operating periods, the PR-PD2HR now offers the most sensitive detection in the series with exclusive signal processing that can detect particles as small as 0.35 m.
-
product
Medical Masks Differential Pressure Tester
Sataton Instruments Technology CO., Ltd
Medical face mask differential pressure tester also called mask breathility tester is to determine the breathability of medical face mask materials. The tester can measure the differential pressure (Delta P) required to draw air through a measured surface area at a constant air flow rate is used to measure the air exchange pressure of the medical face mask materials. By providing the suction air through the holding sample, the tester can measure the Delta P by differential pressure transducer. It is to determine the air permeability and using comfort of the materials for medical mask.
-
product
Face Masks Particulate Filtration Efficiency PFE Tester
GLE-20
GLE-20 is an oil-salt two-in-one Face Masks Particulate Filtration Efficiency PFE Tester. According to ASTM F1862-17, ASTM F2299-03 (2017), ASTM F2100-2019, BS EN14683-2019, BS EN 14387-2004+A1 2008, BS EN 136-1998, BS EN 140-1999, BS EN 143-2000 +C1-A1, BS EN 149-2001+A1, etc. It is used to test the particulate filtering efficiency of daily protective masks and medical masks, and to determine the obstruction performance of ordinary fabrics and medical protective masks against a constant flow of airflow.
-
product
Medical Masks Synthetic Blood Penetration Tester
WKS-8010
WKS-8010 Medical Masks Synthetic Blood Penetration Tester is to test the mask material with synthetic blood under continuous pressure, and visually inspect the penetration of synthetic blood on the material. It is suitable for the resistance of masks to the penetration of synthetic blood under different levels of test pressure.
-
product
Masks Synthetic Blood Penetration Tester
Sataton Instruments Technology CO., Ltd
Medical face masks synthetic blood penetration resistance tester is to evaluate the penetration – splash resistance property of medical face masks by the impact of a small fixed volume of a high-velocity stream of synthetic blood which is projected horizontally. The pneumatically controlled valve will simulate the splatter of blood or other body fluid to disburse at the specimen mask. The tester is suitable to determine the synthetic blood penetration of materials or certain materials used in medical face masks.
-
product
Masks Flame Retardant Performance Tester
WKS-1208
WKS-1208 Masks Flame Retardant Performance Tester is used to test the burning performance of the mask after contacting the flame at a certain linear velocity. It is special test instrument for the flame retardant performance of masks.
-
product
GENERAL INSPECTION MACHINE AFTER SOLDER MASK
DVI is a technology of automated optical inspection, which can inspect deep to the difference from semi-transparent layers or semi-reflective layers.
-
product
Mask Flatness Measurement System
Tropel® UltraFlatTM 200 Mask System
The Tropel® UltraFlatTM 200 Mask System was designed specifically for the photomask industry. It delivers the lowest measurement uncertainty for ever-tightening mask flatness specifications. Shrinking device features require not only flatter wafers, but flatter masks.
-
product
Mask Produce and Test Machine
LISUN produce the bfe tester for face mask, pfe tester, melt-blown cloth electrostatic electret generator according to ASTM F1862-17, ASTM F2299-03 (2017), ASTM F2100-2019, BS EN14683-2019, BS EN 14387-2004+A1 2008, BS EN 136-1998, BS EN 140-1999, BS EN 143-2000 +C1-A1, BS EN 149-2001+A1
-
product
Large Substrate Mask Aligner
Model 6020
The Model 6020 is a large substrate Production Mask Aligner or Auto-flood Exposure System for RDL First Level Advanced Packaging (PLP) and markets requiring exposure of large glass panels. It is engineered with OAI’s precision, reliability, and quality that is found in all of OAI’s products. The features include wedge effect leveling, superb process repeatability, ≤ 2.0µm printing resolution, and remote diagnostics. Using robotic handling, the system can stand alone or be fully integrated with photo resist processing.
-
product
Photo Type Tachometer
DT-2234A
MEASUREMENT RANGE:2.5～99,999r/min. ACCURACY:±(0.05%n+1d) . POWER SUPPLY:4X1.5V AA(UM-3)BATTERY
-
product
Photo Detector with Integrated Transimpedance Amplifiers
ADN3010-11
Analog Devices optoelectronic amplifiers include a range of germanium photodiodes that, through a proprietary process, have been monolithically integrated with silicon transimpedance amplifiers and limiting amplifiers. This process eliminates the need for bond wires connecting the photodiode to the transimpedance amplifier, which leads to improved performance and greater manufacturing reliability. Our portfolio of products also supports the growing need for optical and electrical interface miniaturization.
-
product
MASK MVM-SEM® E3600 Series
E3640
Ongoing semiconductor process shrinks are driving new demand for stable, highly precise measurement of pattern dimensions for photomask and wafer production. The E3640 satisfies these requirements with industry-leading precision measurement capabilities and upgraded functionality that enhances mask R&D and production efficiency.
-
product
Photo Optic Sensors
From patient monitoring in hospitals, to wearables and home healthcare applications, TE Connectivity (TE) offers photo optic sensors and components for non-invasively measuring blood oxygenation (SpO₂) level. With more than 27 years of proven reliability and expertise, TE has designed SpO2 sensors with best-in-class flexibility to accommodate multiple wavelength options. Our ability to provide both components and complete sensor packages make us the leading choice for pulse oximetry applications that require high degrees of precision, durability and performance.
