Filter Results By:
Products
Applications
Manufacturers
Microphones
convert sound pressure to an electrical current.
See Also: Phone, Telephone, Geophones, Headphone, Hydrophones, Measurement Microphones, Mic, Electroacoustic, Headset
-
product
Type 1 Phantom Powered Measurement Microphone
MK224PH
The MK224PH Type 1 phantom powered measurement microphone system offers a cost effective solution to acoustic measurements from phantom powered sources. Frequency Response: +/-2dB (8 Hz to 18kHz). Sensitivity: 50 mV/Pa (-26 dBV/Pa)typ. Dynamic Range 3% THD: 14dBA-145dB.
-
product
Sound Level Calibrators
PeakTech Prüf- und Messtechnik GmbH
For sound level measurements in extreme conditions, at high altitudes or high demands on the accuracy of the measurement results, sound level meters should be checked prior to the measurement with a sound level calibrator. Also for calibration and verification of microphones in audio technology, you need a sound level calibrator, which is designed to produce several sound pressure levels at a fixed frequency characteristic. This calibrator has two switchable calibration steps.
-
product
30KHZ Measurement Microphone
M30
Used on countless full-scale concert tours, as well as in scientific research laboratories, tropical rainforests, and rocket testing facilities, the M30 has proven to be a lab-grade audio instrument that can handle any environment.
-
product
Acoustic Imaging
Acoustic imaging offers cutting-edge solutions for precise leak detection, partial discharge identification, and mechanical fault diagnosis. With high-performance microphone arrays and advanced algorithms, our products ensure exceptional industrial safety and perfomance.
-
product
SparkFun Analog MEMS Microphone Breakout
SPH8878LR5H-1
The SparkFun Analog MEMS Microphone Breakout makes it easy to work with the SPH8878LR5H-1 analog microphone from Knowles. This board features an OpAmp to bring the output of the microphone to a usable level, allowing you to plug directly into an ADC on a microcontroller or something like the SparkFun Spectrum Shield.
-
product
Microphone Arrays
One of the most important parts of an Acoustic Camera is the microphone array. It determines the spatial distribution of the acoustic microphones and therefore measurement performance of the whole system. In order to achieve the maximum possible performance in any given application, we offer a wide variety of microphone arrays. No matter if the measurement is beamforming, intensity or holography ... we have the right microphone array. For special applications we can design and build custom made microphone arrays according to the requirements of the application.
-
product
ICP Electret Surface Microphone
130B40
Low-profile surface pressure microphone and preamp, prepolarized
-
product
Ultraminiature Microphone
MB-2200M10
MB-2200M10 is an ultra compact and lightweight microphone that enables measurement in narrow spaces, where have been difficult to install, without giving influence to the sound field.Its compact and lightweight features make you possible to perform measurements in a limited space, such as multi-point measurement, and measurement near the sound source. As CCLD type, the MB-2200M10 can be connected to Ono Sokki’s FFT Analyzer or CCLD supported devices.
-
product
Precision Condenser Microphone
377C10
Performance:Nominal Microphone Diameter:1/4"CharacteristicPressure Open Circuit Sensitivity1.0 mV/Pa1.0 mV/PaFrequency Range (2 dB)4 to 70000 Hz4 to 70000 Hz Lower Limiting Frequency (-3 dB)0.25 to 3.0 Hz0.25 to 3.0 Hz Resonant Frequency (90 Phase Shift)65000 Hz65000 HzHumidity Coefficient of Sensitivity (0 to 100%, non-condensing)0.0012 dB/%RH0.0012 dB/%
-
product
Externally Polarized Precision Condenser Microphones & Preamplifiers
Externally polarized microphones set the initial standard for all acoustic test and measurement applications. They rely on a dedicated 200V power supply and specialized cables with 7-pin LEMO® connectors. Their straightforward design supports a wide product range. Often chosen as replacements for existing models or when prepolarized alternatives are unavailable.
-
product
PCI-4461, 204.8 kS/s, 118 dB, 3.4 Hz AC/DC Coupled, 2-Input/2-Output Sound and Vibration Device
779307-01
The PCI‑4461 is a high-accuracy data acquisition module specifically designed for sound and vibration applications. It provides simultaneous two-channel dynamic signal generation and simultaneous two-channel dynamic signal acquisition with six gain settings to configure the input range. The PCI‑4461 also includes software-configurable AC/DC coupling and integrated electronic piezoelectric (IEPE) conditioning to ensure precision measurements with microphones, accelerometers, and other transducers that have very large dynamic ranges. Common applications include audio test; automotive test; noise, vibration, and harshness (NVH) analysis; and machine condition monitoring.
-
product
Fixed Mount Strobes
Our fixed mount stroboscopes are designed for installation in applications requiring continuous stroboscopic visual inspection. The MVS is available with xenon or LED light output with adjustable pulse width and focal distance for optimized target illumination. Connect your existing trigger signal or the optional Frequency Controller with LCD. Connect multiple units together in parallel for applications with wide illumination area requirements. Use the optional Audio Interface Box and microphone to create stunning audio driven visual effects.
-
product
Plug-On Transmitter
DPR
This unique plug-on transmitter design will ideally match any microphone or line level source via a standard XLR connector. The DPR can tune in 100 kHz or 25 kHz steps across the UHF television band from 470.100 to 607.950 MHz, with a selectable output power of 25 or 50 mW. The purely digital architecture utilizes AES 256-CTR encryption for high level security applications.
-
product
Measurement Condenser Microphone
ECM8000
The ECM8000 is a specialized condenser microphone designed for use with real-time analyzers, such as our ULTRACURVE DEQ2496, to provide an accurate acoustic picture of the room. You can then use your graphic EQ to fine-tune your system's performance to perfectly match the characteristics of any acoustic environment.
-
product
Sound Level Meters
Dalian Taijia Technology Co.,Ltd
Is used for acoustic measurements. It is commonly a hand-held instrument with a microphone.
-
product
Low Noise Prepolarized Microphone
378A04
The 378A04 is a matched system that is comprised of a high sensitivity microphone and a low noise preamplifier that contains a built-in filter that enables the free-field response to remain flat over a wide frequency range. The system requires a minimum of 4 mA and measures to 6.5 dBA (5.5 dBA typical) within a cost efficient, prepolarized (0V) design. PCB's model 378A04, the industry's first prepolarized low noise microphone and preamplifier system allows you to measure extremely low amplitudes. In the past this was only possible with externally polarized solutions. With a typical noise floor of 5.5dBA, this microphone system delivers all of the benefits commonly associated with prepolarized systems.
-
product
Microphone Preamplifier
426A30
1/2-inch preamplifier with 7-pin LEMO connector (for externally polarized microphones)
-
product
Digital Matrix Processor
DM812
The DM812F is a powerful digital audio processing, mixing and routing system. The primary applications are sound reinforcement and conferencing in boardrooms, courtrooms, worship centers, distance learning systems, hotels and other applications with multiple microphones and loudspeakers. The design represents a milestone in DSP technology in its basic architecture and in its processing speed and efficiency.
-
product
Acoustic Calibrator
CAL150
The Larson Davis CAL150 Sound Level Calibrator is a battery operated precision microphone calibrator used for the calibration of sound level meters and other sound measurement equipment
-
product
LogiCue Systems
LogiCue 6
The LogiCue 6 controller has many of the same features as the LogiCue 12. It has 6 channels of control, LED indicators that mimic the color of each channel, a 2-way “acknowledge” feature that allows actors or crew members to respond to the stage manager with the press of a button, and self-test on power up. The controller connects to the cue lights using standard microphone cable.
-
product
PXIe-4497, 204.8 kS/s, 114 dB, 2 Gains, AC/DC-Coupled, 16-Analog Input PXI Sound and Vibration Module
781369-01
204.8 kS/s, 114 dB, 2 Gains, AC/DC-Coupled, 16-Analog Input PXI Sound and Vibration Module - The PXIe‑4497 is designed for high‑channel‑count sound and vibration applications. With 24-bit analog inputs and IEPE constant current signal conditioning, the PXIe‑4497 is ideal for making precision measurements with microphones, accelerometers, and other transducers that have very large dynamic ranges. The PXIe‑4497 delivers simultaneous sample on all channels. In addition, the module includes built-in antialiasing filters that automatically adjust to your sample rate, software-selectable input gain, and TEDS smart sensor support for error-free setup. Common applications include noise, vibration, and harshness (NVH) analysis; large microphone arrays; and dynamic structural test.
-
product
Test Sockets
MEMS Device
Patented MEMS Sockets from Ardent Concepts use a unique scrubbing action contact set which is ideal for today’s sensitive MEMS devices, including accelerometers, gyroscopes, MEMS microphones and other specialized devices used in mobile electronics applications
-
product
Audio Analyzer
MS20
The MiniSonic MS20 is a combined oscillator and measuring set in a stand-alone unit, which is both compact and portable. As well as being a quality tester the MS20 is a precision line-up tool, a stereo PPM, a balanced-unbalanced convertor (both ways), a stereo microphone pre-amp, a headphone amp, and a level convertor.
-
product
HEAD artificial head microphones
HSU III
The HEAD-Shoulder-Unit HSU III is an artificial head microphone for binaural recordings.
-
product
Simulation Software
CoventorWare
CoventorWare is an integrated suite of design and simulation software that has the accuracy, capacity, and speed to address real-world MEMS designs. The suite has many MEMS-specific features for modeling and simulating a wide range of MEMS devices, including inertial sensors (accelerometers and gyros), microphones, resonators, and actuators. The included field solvers provide comprehensive coverage of MEMS-specific multi-physics, such as electrostatics, coupled electro-mechanics, piezoelectric, piezoresistive, and damping effects.
-
product
C-Mic Testing System
BK3010
The BaKo BK3010 is our main C-Mic tester. It's small enough to carry under your arm and with a test time of under 0.5 seconds, it tests as fast as you can connect a microphone. Setting up the specifications is so easy and intuitive, we based the BK3012 D-Mic Tester on it. It is also the model for our BK9010B Fully Automatic C-mic Tester.
-
product
Sound Level Meters
A sound level meter is used for acoustic (sound that travels through air) measurements. It is commonly a hand-held instrument with a microphone. The diaphrahm of the microphone responds to changes in air pressure caused by sound waves.
-
product
Configurable Data-Logging System
NI CompactDAQ
This NI CompactDAQ configurable data-logging system includes an NI CompactDAQ controller or chassis, C Series I/O modules, and Chameleon software. It is designed for structural test and monitoring applications with the NI CompactDAQ controller, which includes built-in processing and nonvolatile storage for running Chameleon software and logging data locally. Alternatively, you can choose a USB or Ethernet chassis for a lower cost system that requires an external PC. This system accepts a variety of C Series I/O modules, so you can mix and match microphones, accelerometers, and temperature and bridge-based sensors.
-
product
MIPI Soundwire Total IP Solutions
Soundwire
Soundwire is suited for small, cost-sensitive audio peripherals such as modern digital class-D amplifiers and digital microphones. The Total MIPI SoundWire IP Solution from Arasan enables early adopters the fastest path to adoption of this new standard by offering a comprehensive IP package that includes the Verilog RTL source code for Master and Slave, fully validated for compliance with the standard, a comprehensive test environment with a compliance suite for verification of the IP package, a SoundWire Hardware Development Kit (“HDK”) for FPGA prototyping, a SoundWire protocol analyzer and a complete SoundWire software stack.
-
product
2-Tone Audio Generator
* 2 tones, 1900 & 700 Hz * 200 mv output * balance & level controls * Individual tone muting *Microphone level output* measures 4.5 x 2.5 x 1.1 inches* 9 volt battery operation
