Filter Results By:
Products
Applications
Manufacturers
Measuring Receivers
measure radio signals.
-
product
Voltage Probe
KHZ43201
Beijing KeHuan Century EMC Technology Co,.LTD
The KHZ43201 voltage probe is a standard low resistance test probe, which meets the technical requirements for this product in the CISPR16-1 and CISPR14-1 test equipment. When measuring the interference voltage of the power grid, the artificial power supply network cannot be used at the load port, and sometimes it is necessary to use a voltage probe to measure the interference of the signal port, the load port, and the antenna port. The input impedance of the voltage probe to the ground wire is greater than 1.5KΩ, which can protect the input terminal of the receiver.
-
product
Surge Voltage Generator
SSG 1100
BAUR Prüf- und Messtechnik GmbH
Cable fault location with the BAUR SSG 1100. Surge voltage generators are used for pre-location and pinpointing of high- and low-resistive as well as intermittent faults in power cables. The energy stored in a high-voltage capacitor is released at regular intervals or as DC voltage. The thus generated acoustic signal at the fault position can be recorded with a ground microphone and a universal receiver.* High surge voltage up to 32 kV* Continuously adjustable voltage* Voltage monitoring through kV meters with 3 measuring ranges* Automatic discharge unit
-
product
In-Situ Cross- Stack Laser Analyzer
LS25 is an in-situ analyzer for non-contact measurement of the concentration of gases. The measuring principle of the LS25 is based on the principle of single line spectroscopy (Tunable diode laser absorption spectroscopy, TDLAS). A single cross-sensitivity-free absorption line of the gas to be measured is selected in the near infrared range. A single-mode diode laser operating at room temperature scans the respective absorption line. By using an opposite receiver, the absorption caused by the sample gas is measured and from this the concentration is calculated. An automatic correction for pressure and temperature changes is possible. In addition, the transmission is displayed respectively output as a signal for preventive maintenance.
-
product
Spectrum Analyzer
SA-S
RF Frequency Range: 1 Hz to 4.2 GHz. Low noise amplifier available above 500 KHz. Wide dynamic range: -151 dBm to +10 dBm. Resolution bandwidths (RBW) of 0.1 Hz to 250 KHz and 5 MHz. Includes a High Dynamic Range Measuring Receiver. 0.25 dB relative accuracy. 0 dBm to -125 dBm, 150 KHz to 1 GHz. 0 dBm to -115 dBm, 1 GHz to 4.4 GHz. Adjustable digital audio filters. Accurate AM and FM measurements
-
product
Field Strength Receiver
KH3933
Beijing KeHuan Century EMC Technology Co,.LTD
KH3933 is a fully automatic interference field strength receiver integrating antenna and receiver. It is an important equipment for space field strength testing. It can be used to measure useless or harmful related radio interference signals in space, as well as medium wave and short wave. The field strength of the radio signal from a radio station. When measuring radio interference signals, this machine complies with GB/15707-1995 , DL/T691-1999 , and is suitable for high-voltage transmission lines and substation radio interference signals. This receiver complies with CISPR16-1 and GB6113-1 manufacturing standards.
-
product
Vector Network Analysers
LA19-13-03
The LA19-13-03 is our latest PC-driven Vector Network Analyser. It provides great flexibility, fast speed and wide dynamic range. It is useful for measuring a wide range of devices from 300 kHz to 8 GHz with 10 Hz resolution. By means of external links on the front panel, the internal couplers can be bypassed for direct access to the internal receivers. This flexibility allows, for example, high power amplifier measurements to be carried out using an external booster amplifier and couplers. It is housed in a small lightweight package making it very portable.
-
product
Active Dual Loop Antenna
KH30936
Beijing KeHuan Century EMC Technology Co,.LTD
KH30936 active dual loop antenna is used for adjusting, testing, measuring and other receivers. It has many advantages:1. The antenna coverage frequency is wide: 150KHz ~ 30MHz .2. The field strength value is measured according to the correction coefficient within the effective frequency range, which is convenient to use.3. The antenna power is supplied by the host, which is convenient for outdoor measurement.4. Compared with the single loop antenna, the advantage is to read the maximum value directly, which eliminates the tedious steps of rotating the antenna to find the maximum value and the interference of the human body to the signal.
-
product
Combo Measuring Receiver/ TV Analyzer
VAROS 106
High accuracy, an easy handling as well as the modularand rugged construction will support the technician onsite in his tasks: perfect troubleshooting in all distribution networks with FM, return channel, DAB/DAB +, DVB-T2, cable TV, WiFi or SAT – the VAROS 106 covers all ranages reliably. By any means a real allrounder.
-
product
Cables
Adapter Cables connect your Spectrum card or instrument with your device under test, your sensor, your transmitter or receiver, your external machine, your prototype equipment or simply with a probe for measuring. To fulfill a lot of different requirements Spectrum is offering adapter cables between different types of connections and with different length. These adapter cables are manufactured for Spectrum following Spectrum's specification.
-
product
Scalar Mixer/Converter Measurements
S96082A
The S96082A offers the solutions for measuring mixers/frequency converters and amplifier's harmonics using the ENA. The frequency offset mode (FOM) provides the capability to tune the ENA's receivers to different frequencies from the source. This enables measuring amplifier's harmonic responses and mixer/converter's conversion loss.
-
-
product
Sattlite Measuring Receiver
VAROS 109
Compact device and yet a full-fledged satellite measuring receiver: the VAROS 109 is used for installation and troubleshooting in classic multi-switch systems as well as UNICABLE/JESS distribution networks.
-
product
Pinpoint Laser Systems Products
The Microgage PRO is the next generation in laser measuring and alignment tools. This extremely versatile measuring and alignment tool combines key features and capabilities into one portable, compact, easy to use, product for multiple industries. A precise laser beam forms a straight reference line for a machine or assembly and each receiver measures in two axial directions, horizontal and vertical (X & Y).
-
product
EMI Test Receiver
ESL
The R&S®ESL EMI test receiver combines two instruments in one, measuring EMC disturbances in accordance with the relevant standards and also serving as a full-featured spectrum analyzer for diverse lab applications. The combination of very good RF characteristics and all of the important functions needed for fast, precise measurement and evaluation of the EMC of a device under test in accordance with commercial standards is unmatched in this instrument class.
-
product
PC Software
AMA.REMOTE
On the one hand the PC software AMA.remote allows you to process measuring receiver files (e.g. tuning memory or channel lists). On the other hand, TV analyzer (combo measuring receiver) AMA 310 can be remotely monitored and controlled via SNMP with AMA.remote.
-
product
Frequency Meter up to 330 GHz
Frequency meter is intended for measuring frequency in range 70-330GHz.The Frequency Meter is based on sweepable heterodyne receiver. Fully outomated system allows to measure frequency without preslection frequency range.This solution is ideal for laboratory test measurement.
-
product
EMI Receiver
Core-6
The "CORE-6" is a very compact (19", 1 RU), new digital EMI receiver which enables the user to make frequency-sweeps within a few seconds what saves hours of measuring timeduring developments.
-
product
Microwave Panoramic Receiver
MVNA-8-350-1-2
It is possible to attach a dual channel receiver VR-8-350-2, to a single-HM microwave part MP-8-350-1, creating in that way a very flexible measuring system, a "microwave panoramic receiver" with which one can extract two separate signals from the single detector HM (or extension ASA-2).
-
product
DataNet Wireless Data Loggers
The DataNet wireless system is a data acquisition solution developed for 24/7 real-time monitoring for mission critical organizations. Boasting a variety of wireless data logger models using ZigBee RF technology, the DataNet solution is capable of measuring parameters such as temperature, relative humidity, voltage, current, or frequency. Choose from DataNet models offering up to 6 inputs or the more cost-effective single or dual input Mini DataNet range, depending on your application requirements. Each DataNet mesh network is managed by a Receiver connected via USB to a Windows-based PC, and also supports addition of wireless Repeater units for extending the network transmission range and improving network robustness.
-
product
TEM Cells
Transverse Electro Magnetic (TEM) cell or Crawford cell (named after its inventor) is used to generate accurate electromagnetic waves over a wide frequency range: DC (0 Hz) to GHz., EM waves generated in the cell propagate in transverse mode and have the same characteristics as a plane wave. It can be used to calibrate E-field broadband probes for testing radiated E-field immunity as well as for measuring radiated emission from a product with a spectrum analyzer/EMI receiver.TEM cell generates a consistent electromagnetic field for testing small RF devices such as wireless pagers, receivers, portable phones, etc.
-
product
Surge Voltage Generator
SSG 3000
BAUR Prüf- und Messtechnik GmbH
Cable fault location with the BAUR SSG 3000. Surge voltage generators are used for pre-location and pinpointing of high- and low-resistive as well as intermittent faults in power cables. The energy stored in a high-voltage capacitor is released at regular intervals or as DC voltage. The thus generated acoustic signal at the fault position can be recorded with a ground microphone and a universal receiver.* High surge voltage up to 32 kV* Continuously adjustable voltage* Voltage monitoring through kV meters with 3 measuring ranges* high surge energy in each voltage range
-
product
Surge Voltage Generator
SSG 1500
BAUR Prüf- und Messtechnik GmbH
Cable fault location with the BAUR SSG 1500. Surge voltage generators are used for pre-location and pinpointing of high- and low-resistive as well as intermittent faults in power cables. The energy stored in a high-voltage capacitor is released at regular intervals or as DC voltage. The thus generated acoustic signal at the fault position can be recorded with a ground microphone and a universal receiver.* High surge voltage up to 32 kV* Continuously adjustable voltage* Voltage monitoring through kV meters with 3 measuring ranges* Automatic discharge unit
-
product
Loss Measuring System for Transformers
LiMOS
HIGHVOLT Prüftechnik Dresden GmbH
The transformer loss measuring system LiMOS is designed for highly accurate measurement of losses and other parameters required in the framework of routine and type testing of power transformers. The combined voltage/current sensors and the digital signal processing enable a very compact design with only one HV device per phase with smallest volume and footprint. The digitized and preprocessed signals are transmitted via fiber optic cable to the receiver unit (LiMO-MCSU).
-
product
PNA-X Network Analyzers
Keysight's PNA-X is more than just a vector network analyzer. It is the world’s most integrated and flexible microwave test engine for measuring amplifiers, mixers, frequency converters, and other active devices. The hardware includes two internal signal sources, a signal combiner, S-parameter and noise receivers, pulse modulators and generators, and a flexible set of switches and RF access points. These hardware features provide a powerful core for a broad range of linear and nonlinear measurements, all with a single set of connections to your device under test.
-
product
Attenuators And Pulse Limiters
A bidirectional attenuator, i.e. the attenuation and power capability specification is valid for both directions. There is a large variety of applications for this attenuator: The measuring range of a spectrum analyzer can be increased. Any kind of meter can be protected against overload; it can be used to control the linearity of a meter reading. It can minimize measurement uncertainty caused by mismatched impedances. During an EMI receiver calibration an attenuator directly at the pulse generator output is inevitable.
-
product
Pipeline & Cable Locator
STC-PCL 1101
Shanghai Stone Communication tech Co., Ltd
STC-PCL1101 Pipeline & Cable Locator consists of a Transmitter and a Receiver, used in the underground utilities route locating, the depth measuring and long distance tracing. We adopted multicoil electromagnetism technology on this Pipeline & Cable Locator, enhanced the pipeline localization to decide the depth precision and the goal pipeline recognition capability, also could accurately carry on tracing and the localization in the pipeline crowded complex region to the goal pipeline. Thus it is widely used in the telecommunication, electric, tap water, natural gas, physical prospecting, town planning and so on.. STC-PCL1101 has many optional accessories, thus increased their use, and expanded their application scope.
-
product
Measuring Receiver
FSMR3000
The R&S®FSMR3000 is a microwave measurement receiver to calibrate signal generators and attenuators with one single instrument. Most important features provided are tuned RF level measurements, level measurements, analog modulation and spectrum analysis. Additionally, the R&S®FSMR3000 can be equipped with powerful hardware for high-end phase noise test supplementary to the standard phase noise test with the spectrum analyzer.
-
product
USB Power Sensor Module For Measuring Receiver
U5532C
The U5532C USB power sensor module is specially design for the N5531X measuring receiver. Based on the Keysight USB power sensor and a power splitter, the U5532C provides the N5531X measuring receiver user with a single RF input device covering up to 50 GHz. Using of the U5532C USB power sensor module eliminates the requirement of an external power meter, simplifying the setup process and saving lab space. The measurement integrity and accuracy are guaranteed by the fully defined specification sets. The traceability of measurement uncertainties is also ensured.
-
product
Network Analyzer
DPNA-6G AXIe
The AXI DPNA-6G module is the world's first network analyzer in the form factor of the AXIe-1 module, as well as the first Russian device that meets the AXIe-1 standard. In the mode of the network parameters meter, the AXI DPNA-6G module measures the vector values of the network parameters on two ports: transmission coefficients (S12, S21) and reflection (S11, S22). At the same time, all necessary types of calibrations are supported: one- and two-port short-circuit, XX, matched load, transmission normalization. The software supports the import of third party calibration standard parameters. In the measuring receiver mode, the module provides:*generation of a harmonic signal (frequency synthesizer);*spectrum analyzer and power level in a given band;*measuring the frequency of a known signal;*measurement of analog modulation parameters;*phase noise measurement.
-
product
Multiplexers
Capable of performing the necessary switching between test points of the device under test, to give access to low frequency measuring instruments, in electronic test systems based on tool receivers.
