Filter Results By:
Products
Applications
Manufacturers
MIL-STD
ensures a product meets military standards.
See Also: Mil, MIL-SPEC, Mil-Std-1553, Mil-Std-1760
-
product
PXIe Avionics Interface Cards
The OmniBus II PXIe is the next-generation of Astronics' popular OmniBus product with faster I/O and processing capabilities. With the newest advanced set of MIL-STD-1553 and ARINC 429 modules, users can verify wave form compatibilities, test functions of bus shorts and opens, and—when combined with our CoPilot® software—perform lab, production and flight test verification and simulation right out of the box. Readily available as Commercial Off-The-Shelf (COTS) products, the PCIe interface is perfect for challenging simulation, test, interface, and data recording applications.
-
product
Combination Module: 2 Ch. MIL-STD-1553 & 12 Ch. Discrete I/O
CM8
The CM8 module is a combination of NAI's MIL-STD-1553B module, FTB, and Enhanced Discrete I/O module, DT4. The CM8 offers twelve channels of discrete I/O and two channels of MIL-STD-1553B communications. The twelve discrete I/O channels are programmable as either input (voltage or contact sensing with programmable, on-module pull-up/pull down current sources), or output (current source, sink, or push-pull) up to 500 mA per channel from an applied, external 3-60 VCC source. The discrete I/O channels also provide additional functionality modes such as Pulse Width Modulation (PWM) output mode and Pattern Generator output mode. The two MIL-STD-1553B communications channels feature a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
product
Micro Coax, Contact, Receiver, RG316 Double Shield
610140104
Primary mating contact 610141104. (May mate with other ITA contacts, as well.)Mechanical SpecificationsDurability 10,000 cyclesContact Material Center Conductor – BeCuShield – BrassContact Plating 50µ" Au over 100µ" NiContact Termination Center Conductor – SolderShield – SolderInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50ΩFrequency Range DC – 10.5 GHzVSWR 1.0225 +.05 f(GHz)Insertion Loss -√f(GHz) x .06 dBDWV 800 V RMSContact Resistance 6 mOhms center/4 mOhms outer Cable Specifications RG316 Double ShieldEnvironmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MOhms Min.
-
product
Interface
RPCC-D1553
This dual channel card is RoHS-compliant and is a direct drop-in replacement for the PCC-D1553 card which it replaces. The RPCC-D1553 comes with all necessary cables for operation. Cables designed for the PCC-1553 card will not work with the RPCC-D1553 card. The RPCC-D1553 provides 1 or 2 channels integrated with powerful API software providing instant access to all MIL-STD-1553 databus functionality and data.
-
product
Bison VX-Server
The beltronic-IPC BISON VX-Server is built for use in industrial and military applications which require this type of robust and reliable system. The Bison VX-Server complies with MIL-STD 810 as well as with high EMC/EMI standards such as MIL461/704/1275 it operates on a 24V DC power environment. A optional UPS function with a LiFePo battery pack can power the system for some minutes independently if the power inputs fail.One of the major advantages of the BISON VX Server is that there are few customization limits. Changes in mechanical structure and various hardware options are available even in small quantities.
-
product
Data Acquisition System - 3U 1-Slot
DAQ-31CP0G
The DAQ-31CP0G is a preconfigured rugged system with a high-performance, low power ARM® Cortex®-A9 processor. It is ideally suited to support a multitude of data acquisition applications that require high-density, multichannel, programmable communications consisting of: ARINC 429/575; Dual-Redundant, Quad Channel MIL-STD-1553B; CANBus (CAN 2.0 A&B or J1939) and Dual-Port Gig-E Ethernet.
-
product
Dual Channel MIL-STD-1553 BC/RT/MT cPCI Intelligent Module
DP-cPCI-5664
The DP-cPCI-5664 provides new level of performance and flexibility for MIL-STD-1553B notice 2 in a Compact PCI form factor. It has full intelligent interfacing between a cPCI bus and one / two independent dual redundant MIL-STD-1553B data buses. The 1553B bus functions are fully controlled by a DSP processor. Software controls the operation of the channel as either a 1553 Bus Controller (BC), Remote Terminal (RT), or Bus Monitor (MT).
-
product
Small Form Factor MIL-STD-1553 Bus Monitor
ES-1553Anlyzr/USB-x-yz
Our new inline Bus Monitor is a very small, very light MIL-STD 1553 Bus Monitor that can be connected to any Windows device with a USB connector. It monitors and records all or selected 1553 traffic for later analysis.Exalt is our Windows base graphical tool that allows you to analyze real time or recorded data using many different views: raw data, engineering units or graphical displays.The combination of a handheld computer, in-line 1553 monitor and Exalt provides a compact solution for monitoring MIL-STD 1553 networks.
-
product
PCIe Mini Card
EXC-1553mPCIe/P1-1760
Each channel of the EXC-1553mPCIe/P1-1760 operates simultaneously as a Bus Controller and/or multiple (up to 32) Remote Terminals, or as a Triggerable Bus Monitor. The card supports error injection and detection. The card’s small size and compatibility with notebook computers make it the perfect solution for performing system simulation of the MIL-STD-1760 bus, in the lab and in the field.
-
product
Interface Module for the Multimode, Multiprotocol Excalibur 400 Family of Carrier Boards
M4K1553Px(S)
The M4K1553Px(S) interface module for the multimode, multiprotocol, Excalibur 4000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.Each M4K1553Px multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M4K1553Px modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.Each M4K1553PxS single function (RT validated) module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.
-
product
Micro Coax, Contact, Receiver, 50 GHz
610140108
Primary mating contact 610141108. (May mate with other ITA contacts, as well.) *This contact sold as a patchcord only.Mechanical SpecificationsDurability 10,000 cyclesContact Material Center Conductor – BeCuShield – BrassContact Plating 30µ" Au over 100µ" NiContact Termination Solder Nut ClampInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50 ΩFrequency Range DC-50GHzVSWR 1.06+0.004 f(GHz)Insertion Loss - .095 x √f(GHz) dBDWV 700 V RMSContact Resistance 6 mOhms center/4 mOhms outer Cable Specifications Flex 405Environmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MOhms Min.
-
product
Single, Dual Or Quad Stream MIL-STD-1553A/BTest And Simulation Module For PCI
APXX1553-x
MIL-STD-1553 Test and Simulation Module for PCI with 1, 2 or 4 Dual Redundant channels (APXX1553-1, APXX1553-2, APXX1553-4) plus 8 programmable discrete Input/Output channels. A unique feature of AIM’s APXX1553-x module is the option for the MILScope™ capability. Models APXX1553-1-DS/APXX1553-2-DS integrate an onboard Analogue to Digital Converter (ADC) which samples, measures and stores the MIL-STD-1553 waveform. Automatic waveform validation is performed by the users Application Software or in conjunction with AIM’s PBA.pro Databus Test and Analysis Software and Test Scripts.
-
product
Interface (PMC)
QPM-1553-TB
The QPM-1553-TB provides the highest level of performance, flexibility and interface density for MIL-STD-1553A/B via PMC (PCI Mezzanine Card) to Thunderbolt 3 device. The QPM-1553-TB is integrated with powerful software that reduces development time. All 1553 databus functionality is supported from our advanced API (Application Programming Interface).
-
product
500W to 1500W - Single Output
LZSA Series
*Five year warranty*-40°C to +71°C Operation*MIL-STD-810E Vibration / Shock*Input transient protected*UL508, SEMI F47, Factory Mutual (Cl 1, Div 2)*Rugged design with conformal coating*Superior thermal design
-
product
2 Channels, MIL-STD-1553/1760 Communications Interface
FTK
Based on the MIL-STD-1553 signal and interface backbone, MIL-STD-1760 defines a standardized electrical interface to address additional aircraft weapons stores management and as such, includes some special requirements. The FTK module meets the operational requirements within the general specifications of MIL-STD-1760 as applied to an integrated I/O function module, and include special designed holt transceivers to ensure signal parameter operation and integrity.
-
product
Biconical Antennas
For many years most standards called for the use of a half-wave dipole antenna set for frequencies above 80 MHz. However, to reduce test time, broadband antennas such as the biconical antenna and log periodic antennas began to be accepted. Broadband antennas, compared to half wave dipoles, reduce test time because the technician did not have to stop the test to adjust the dipole antenna for each frequency. A.H. Systems'' 7 models of Biconical Antennas operate efficiently over the frequency range of 20 MHz to 18 GHz. Suitable for FCC, MIL-STD, VDE, TEMPEST, and immunity testing, each Biconical antenna will provide reliable, repeatable measurements.
-
product
Avionics Network Solutions HSI1760 NIC, SAE AS5653 Compliant
Avionics Interface Technologies
AIT's HS1760 (MIL-STD-1760E) as profiled under SAE AS5653 products are built on our Fibre Channel Simulyzer™ and HS1760 IP Core technology. Our HS1760 products provide Network Controller (NC), Network Terminal (NT), and FC-AE Switch capabilities.
-
product
MIL-STD-1553
The Avionic Interface MIL-STD-1553 products offer solutions for flight test instrumentation (FTI), for data acquisition, for protocol analysis, embedded IP solutions and COTS applications.
-
product
MIL-STD-1553 MCH
M4K1553MCH
The M4K1553MCH interface module for the multimode, multiprotocol, Excalibur 4000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.The M4K1553MCH contains 32k x 16 of dual-port RAM for Data blocks, Control registers, and Look-up tables. All Data blocks and Control registers are memorymapped and may be accessed in real time. The dual-redundant 1553 module may be programmed to operate in one of four modes of operation: Bus Controller, Remote Terminal, RT/Concurrent-Bus Monitor, and Bus Monitor. The M4K1553MCH comes complete with Windows software, and a C driver software library including source code.
-
product
PXI/PXIe MIL-STD-1553 Multiplexer, Single 4-Channel, 2-Pole
42-739-005
The 40-739-005 (PXI) and 42-739-005 (PXIe) are single 4-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.
-
product
450W to 900W - Single Output / Multiple Output
VEGA Series
*1-11 Wide Range Outputs with Adjustment*Cooling - System air/End fan/Reverse fan*48VDC Input Option*Medical Approval Options*MIL-STD-810 Shock and Vibration*PFC compliant to EN61000-3-2*Safety Agency Approvals EN, cULus, BSI, CE
-
product
RF Connectors
SMB Connectors
The SMB interface features a snap-on coupling mechanism and is available in 50 ohm configurations. SMB connectors conform to the requirements of MIL-C-39012, and the interface is in compliance with MIL-STD-348. SMB connectors offer broadband performance with low reflection DC to 4 GHz and extended performance up to 10 GHz.
-
product
Coax, Contact, Receiver, 75 Ohm, RG179
610104157
Primary mating contact 610103169. (May mate with other ITA contacts, as well.)Mechanical SpecificationsDurability 20,000 cyclesContact Material Female & Male Shield – brassCenter Contact – BeCuContact Plating Center Conductor Shield – 30µ” Au over 100µ” NiContact Termination Center Conductor – Crimp or SolderShield – CrimpInsulator PTFEMating Force 4.0 lbs max [1.81 kg]Electrical SpecificationsCharacteristic Impedance 75 ΩFrequency Range DC to 3 GHzVSWR < 2.95 @ 3 GHzInsertion Loss -1.64 @ 3 GHzDWV 800 VRMSContact Resistance Center Contact - 5 mΩOuter Shield - 3 mΩCable Specifications RG179Environmental SpecificationsOperating Temperature -55°C to +125°CVibration MIL-STD 1344, Method 2005, Test Condition 4Shock MIL-STD 1344, Method 2004, Test Condition AInsulation Resistance 1000 MΩ min.
-
product
Automated Thermal Stress System
ATSS Series
Thermotron's Automated Thermal Stress Systems (ATSS) facilitate extremely rapid product temperature change rates in a space-saving, self-contained design that accelerate a Thermal Stress test. Thermotron's ATSS chambers meet the latest MIL-STD 883E and MIL-STD 202F thermal shock specifications as well as JEDEC and IPC test methods. ATSS chambers are capable of the following: Rapid thermal shocking, Accelerated product stressing, Controlled thermal cycling in a self-contained, compact design. With separate hot and cold zones, the Automated Thermal Stress System was designed with a patented retractable product transfer carrier that makes full use of the available working volume in both temperature zones for increased product loading and throughput. The product transfer carrier reduces the overall height requirements of the chamber and is made as light as possible to minimize thermal loading restraints. Thermotron ATSS chambers can be used as part of most commercial reliability and quality control programs, helping to determine:
-
product
PCI Express Card
EXC-4000PCIe/xx
The EXC-4000PCIe/xx card for the PCI Express bus supports up to four dual redundant 1553 channels using the M4K1553Px(S) module and is compatible with all common variations of MIL-STD-1553 (A, B).
-
product
MIL-STD-1553 A / B Test And Simulation PMC Module
PMC-1553
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems*Heat sink and / or protective coating available*Optional input / output for front panel
-
product
FPGA UDP Packet Interface Connnecting 3-4 Channels of MIL-STD-1553 to Ethernet in Real-Time
ENETX-1553
ENETX-1553™ is an innovative product that provides “remoting” of 1553 operations on 10/100/1000 Ethernet IP/UDP local area networks (LAN). ENETX-1553 is a small, low-power, rugged device that provides real-time Ethernet connectivity to for three or four dual redundant 1553 (A/B) buses (channels). Ideal for remoting 1553 connections for in-field applications or point-point lab usage. AltaAPI provides and highly portable BSD SDK and National Instruments LabVIEW and LabWindows. ENET products are unique in the market as they have a hardware, FPGA real-time UDP engine – no OS or IP stacks – provides maximum throughput and ultimate virus protection.
-
product
Aircraft Data Recording
COTS
Our powerful and flexible Ballard Avionics I/O Computers provide the platform for Silo Data recording. These rugged, conduction-cooled, COTS devices combine a powerful computer processor, multi-protocol databus interfaces (MIL-STD-1553, ARINC 429, ARINC 717, ARINC 708), Ethernet, USB, serial, discrete I/O, and other I/O in a small, lightweight package. They deliver outstanding performance on the ground and in the air and are routinely deployed on helicopter, fixed wing, ground mobile, and marine platforms.
-
product
2-CH MIL-STD-1553A/B Bus Simulator Module
1553 WA73A-455
The WA73A-455 MIL-STD-1553A/B Bus Simulator Module allows a system controller in an ATE system to communicate with and test devices that conform to the MIL-STD1553A/B data bus used in military aircraft and communications systems. Each of the WA73A-455's two channels operate as two separate and independent channels with their own VXIbus logical address, interrupts, and complete set of controls and indicators. As a result, each channel of the WA73A-455 is truly an independent instrument, and, therefore, individually programmable.
-
product
Modular Open Systems Approach (MOSA) Solutions
NAI’s Modular Open Systems Approach (MOSA) solutions provide customers with pre-configured, pre-validated, rugged military embedded solutions that save development time and cost while reducing program risk. These Flexible, Adaptable, Configurable, Modular and Expandable Systems Eliminate custom designs and redesigns by taking advantage of NAI’s Configurable Open Systems Architecture (COSA). NAI's full suite of MOSA Solutions are ARM® Cortex®-A53 processor-based and are ruggedized to withstand -40° C to +71° C and qualified to MIL-STD-1275D & MIL-STD-704A with 50 ms holdup (VITA 62 power supply); MIL-STD-461F and MIL-STD-810G.
